Sapido MB-1112 User manual

http://www.sapido.com.tw/ User Manual 1.0
1

http://www.sapido.com.tw/ User Manual 1.0
2
FCC Statement
Federal Communication Commission Interference Statement This equipment has
been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
1. The device complies with Part 15 of the FCC rules. Operation is subject to the
following conditions:
2. This device may not cause harmful interference, and this device must accept any
interference received, including interference that may cause undesired
operation.
3. FCC RF Radiation Exposure Statement: The equipment complies with FCC RF
radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
4. This Transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
5. Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user authority to operate the
equipment.
IMPORTANT NOTE
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance20cm between the radiator & your body.

http://www.sapido.com.tw/ User Manual 1.0
3
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
National Restrictions
Frequency range - 2400.0 - 2483.5 MHz
Country Country Reason/remark
Bulgaria none General authorization required for outdoor use
and public service.
France Outdoor use limited to 10 mW e.i.r.p. within the
band 2454-2483.5 MHz
Military Radiolocation use. Refarming of the 2.4
GHz band has been ongoing in recent years to
allow current relaxed regulation. Full
implementation planned 2012.
Italy none If used outside of own premises, general
authorization is required.
Luxembourg none General authorization required for network and
service supply (not for spectrum).
Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from
the centre of Ny-Ålesund.
Russian
Federation none Only for indoor applications.
Note: Please don’t use the product outdoors in France
CE Statement of Conformity
Our product has been tested in typical configuration by Ecom Sertech Corp and was found to
comply with the essential requirement of "Council Directive on theApproximation of the Laws
of the Member Sates relating to Electromagnetic Compatibility" (89/336/EEC; 92/31/EEC;
93/68/EEC). The Declaration of Conformity can be found at the Sapido regional website.
www.sapidotech.de
CE Information of Disposal
The electric and electronic equipment or unit which is labeled with crossed-out wheeled bin
may not be disposed of with household waste. This mark is based on European Directive
2002/96/EC (for Waste Electric and Electronic Equipment=WEEE).
Please take it to the designated collection facilities. We will ensure the proper recycling, reuse
and other forms of recovery of WEEE. WEEE has the potential effects on the environment
and human health as a result of the presence of hazardous substances. You can contribute to
eliminate these effects by your cooperation.

http://www.sapido.com.tw/ User Manual 1.0
4
Safe Seating Gestures
You should follow the manufacturer’s instructions for adjusting the backrest to fit your body
properly.
An adjustable chair that provides firm, comfortable support is best.
Adjust the height of the chair so your thighs are horizontal and your feet flat on the floor.
The back of the chair should support your lower back (lumbar region).

http://www.sapido.com.tw/ User Manual 1.0
5
Table of Contents
1. Introduction...................................................................................................................................7
1.1 Overview ......................................................................................................................7
1.2 Features .......................................................................................................................7
1.3 Specifications..............................................................................................................8
1.4 Product Appearance...................................................................................................9
1.5 Power Source............................................................................................................10
2. System and Network Setup.......................................................................................................12
2.1 Build Network Connection.......................................................................................12
2.2 Network setup ...........................................................................................................13
2.2.1 Windows 2000...................................................................................................13
2.2.2 Windows XP......................................................................................................14
2.2.3 Windows Vista / Windows 7 ............................................................................15
2.3 Router IP Address Lookup.......................................................................................16
2.3.1 Log into Web GUI .............................................................................................17
3. Internet Connection....................................................................................................................19
3.1 Plug and Play.............................................................................................................19
3.2 Connect to Internet through web GUI.....................................................................19
3.2.1 WAN Interface- 3.5G.........................................................................................21
3.2.2 WAN Interface- Ethernet Port..........................................................................24
3.2.2.1 Access Type- Static IP .....................................................................................25
3.2.2.2 Access Type- DHCP Client ..............................................................................26
3.2.2.3 Access Type- PPPoE........................................................................................27
3.2.2.4 Access Type- PPTP..........................................................................................28
3.2.2.5 Access Type- L2TP...........................................................................................29
3.2.3 WAN Interface- Wireless..................................................................................30
4. Wireless Setup............................................................................................................................32
4.1 Wireless Setup ..........................................................................................................32
4.1.1 Setup Wireless LAN by WPS button...............................................................32
4.1.2 Wireless Basic Setup from Web GUI..............................................................34
4.1.2.1 Multiple APs......................................................................................................36
4.1.2.2 Enable Universal Repeater Mode ...................................................................37
4.2 Wireless Security ......................................................................................................38
4.3 Wireless Access Control..........................................................................................41
5. Security Setup ............................................................................................................................43
5.1 NAT .............................................................................................................................43
5.1.1 Visual Server.....................................................................................................43

http://www.sapido.com.tw/ User Manual 1.0
6
5.1.2 DMZ....................................................................................................................44
5.2 Firewall.......................................................................................................................45
5.2.1 Port Filtering.....................................................................................................45
5.2.2 IP Filtering.........................................................................................................46
5.2.3 MAC Filtering....................................................................................................47
5.2.4 URL Filtering.....................................................................................................48
6. Advanced Setup .........................................................................................................................49
6.1 LAN Interface Setup..................................................................................................49
6.2 Dynamic DNS Setting ...............................................................................................50
6.3 Wireless Advanced Setup........................................................................................51
6.3.1 WDS Settings....................................................................................................52
6.3.2 WPS ...................................................................................................................56
6.4 System Management ................................................................................................58
6.4.1 Change Password ............................................................................................59
6.4.2 Upgrade Firmware............................................................................................60
6.4.3 Profile Save.......................................................................................................61
6.4.4 Time Zone Setting ............................................................................................64
6.4.5 UPnP Setting.....................................................................................................65
6.4.6 Language Setting .............................................................................................66
6.5 Log & Status..............................................................................................................66
6.5.1 Network Config.................................................................................................67
6.5.2 Event Log..........................................................................................................68
6.6 Logout........................................................................................................................69
7. DDNS Service Application.........................................................................................................70
8. Q & A............................................................................................................................................76
8.1 Installation .................................................................................................................76
8.2 LED.............................................................................................................................76
8.3 IP Address..................................................................................................................77
8.4 OS Setting..................................................................................................................77
8.5 3.5G Mobile Router Setup ........................................................................................79
8.6 Wireless LAN.............................................................................................................81
8.7 Support ......................................................................................................................83
8.8 Others.........................................................................................................................84
9. Appendices .................................................................................................................................85
9.1 Operating Systems ...................................................................................................85
9.2 Browsers....................................................................................................................85
9.3 Communications Regulation Information ..............................................................85

http://www.sapido.com.tw/ User Manual 1.0
7
1. Introduction
1.1 Overview
Equipped with HSUPA module, and high capacity LI-ON battery, N+ Mobile 3G Modem
Router is self-contained, no need for power adapter and external USB modem for Internet
connection. As long as there is 3G signal, you can create your own hotspot wherever you
may be. Furthermore, all your WiFi device, such as computers, iPad, gaming gear, smart
phone, photo frame ...etc. can attach to N+ Mobile 3G Modem Router , and get online in
minutes.
By adopting latest, state-of-the-art WLAN technology, N+ Mobile 3G Modem Router
implements cutting-edge Green WLAN "Active-ECO" algorithm, which controls automatically
the power consumption in accordance with WLAN and Ethernet activities, no setting or
push-button required. Plus the low power consumption, environmental-friendly design, N+
Mobile 3G Modem Router creates staggering 6 hours operation, and 48 hours stand-by
battery usage without performance compromise.
Whether in-car Internet, campus network access, or Internet activities at tradeshows, or just a
home network without ADSL reaches, N+ Mobile 3G Modem Router helps you establishing
the Internet connection in minutes.
1.2 Features
With latest Green WLAN technology, no more setting or push-button required to save up
to 80% energy without compromise performance.
Internal HSUPA module for 3G wire-free mobile Internet access
Superb 802.11n 2T2R data rate: Max. 300Mbps downstream/upstream
MultipleAP, Wi-Fi Protected Setup (WPS) button and WPA-PSK/WPA2-PSK support
Automatic WAN type detection to establish the Internet within minutes no expertise
required
Fail-over backup mechanism to ensure your network connectivity
One-touch WPS button for secure wireless network inter-connection
UPnP, QoS, VPN pass-through, advanced firewall security with port filter, URL blocking
support

http://www.sapido.com.tw/ User Manual 1.0
8
1.3 Specifications
Hardware specification
HSUPA 3GPP R6, up to 5.76Mbps UL
HSDPA 3GPP R6, up to 7.2M bps DL,
category 7/8
UMTS Up to 384 Kbps DL and UL
EDGE 3GPP Release4, class 12, up to
237 Kbps DL and 118Kbps UL
Technical Standard
GPRS Up to 85.6 Kbps DL and 42.8 Kbps
UL
GSM/GPRS/EDGE 850/900/1800/1900 MHz
WAN 1
Frequency Band UMTS Please contact your product
supplier for UMTS band request
Ethernet 1 x 10Base/100M Base-TX, Auto MDI / MDI-X
(Can be used as WAN via setting)
WLAN IEEE 802.11n (802.11b/g backward compatible)
LED WIRELESS/WPS, LAN/WAN, 3.5G, STATUS, POWER
Antenna Internal antenna x 2, 2T2R
Operation
Power Supply 12VDC power adapter, LI-ON battery, or mini USB: 5VDC, 2A
Operation Temperature
0℃to 45℃(32℉to 113℉)
Humidity 5% to 95% Non-Condensing
Dimension 91 x 78 x 30 (mm)
Software Specification
WAN
Connection Type 3G /DHCP / Static IP / PPPoE / PPTP / L2TP client/ Wi-Fi AP
Connection Scheme Connection-on-Demand, Auto-disconnect
Active Mode Always ON, Active on Demand, WAN status check
Wireless LAN
WLAN data rate WiFi: 802.11n (up to 300Mbps, 2T2R
), 802.11g (up to 54Mbps), 802.11b (up
to 11Mbps)
Antenna Gain Internal 2T2R, 15dbm antenna
Security WEP 64 or 128 bit/WPA/WPA2/WPA2 Mixed, WPS, WDS
Network Features
NAT DMZ Host, Port-Redirection/Virtual server / Universal Plug-and-Play (discover & transversal) / Dynamic Domain Name System (DDNS) / VPN
pass-trough (IPSec, PPTP),
Firewall Policy-Based IP Packet Filter
MAC address filtering, System logging via Syslog
Access control IP filtering , Port filtering, URL filtering, MAC address filtering
Management
Web-based GUI for remote and local management
Available Syslog monitoring support

http://www.sapido.com.tw/ User Manual 1.0
9
1.4 Product Appearance
The Front
LED Indicator Status Description:
Status
LED Indicator
Solid Flashing
WIRELESS & WPS
Operation OK Green: Transmitting Data
Red: WPS enabled
LAN / WAN Ethernet connected Transmitting Data
3.5G HSPA service is available Connected to a network using HSPA
STATUS Operation OK Green: Reset / Firmware updates in
progress
Power Green: Battery fully charged
Red: Low battery Green: DC Power input or Battery charging
Side

http://www.sapido.com.tw/ User Manual 1.0
10
Power On / Off Power switch
LAN/WAN RJ-45 Ethernet 10/100 Ports
WPS Button WPS function
Reset Button Back to default setting
Mini USB Power supply only
DC Power Jack DC adapter plugged in
SIM Card Slot The SIM card is inserted here
The Rear
Battery Li-Ion Battery x2
Battery Compartment Batteries are placed here
Note: It normally takes at least 4 hours to fully charge the battery. New batteries or batteries stored for
a long time may take more time to charge.
1.5 Power Source
N+ Mobile 3G Modem Router will work from its battery or when plugged into a power source.

http://www.sapido.com.tw/ User Manual 1.0
11
Battery: The battery will last for up to 6 hours. Charge the battery by plugging in the AC
adapter or car charger.
Wall power: Use the N+ Mobile 3G Modem Router by plugging it into a wall socket, the
router battery will charge while it is plugged in.
Mini USB power from a computer or car charger: Plugged into USB port of a computer
via a USB Y cable or a vehicle by a car charger. The battery will charge while it is
connected with a vehicle.

http://www.sapido.com.tw/ User Manual 1.0
12
2. System and Network Setup
To begin with N+ Mobile 3G Modem Router , you must have the following minimum system
requirements. If your system can’t correspond to the following requirements, you might get
some unknown troubles on your system.
Internet Account for XDSL/Cable Modem, broadband or 3G
One Ethernet (10 BASE-T or 10/100 BASE-TX) network interface card.
TCP/IP and at least one web browser software installed (E.g.: Internet Explorer 5.0,
Netscape Navigator 7.x,Apple Safari 2.03 or higher version).
At lease one 802.11g (54Mbps) or one 802.11b (11Mbps) wireless adapter for wireless
mobile clients.
Recommended OS: Windows XP, Vista or Win 7 / Linux.
2.1 Build Network Connection
Administrator can manage the settings for WAN, LAN, Wireless Network, NAT, password,
User Accounts, Firewall, etc.
Please confirmation the network environment or the purpose before setting this product.

http://www.sapido.com.tw/ User Manual 1.0
13
2.2 Network setup
After the network connection is built, the next step is setup the router with proper network
parameters, so it can work properly in your network environment. Before you connect to the
wireless router and start configuration procedures, your computer must be able to get an IP
address from the wireless router automatically (use dynamic IP address). If it’s set to use
static IP address, or you’re unsure, please follow the below instructions to configure your
computer with dynamic IP address:
If the operating system of your computer is….
Windows 2000 - please go to section 2.2.1
Windows XP - please go to section 2.2.2
Windows Vista/Win7 - please go to section 2.2.3
2.2.1 Windows 2000
Click “Start” button (it should be located at lower-left corner of your computer), then click
control panel. Double-click Network and Dial-up Connections icon, double click LocalArea
Connection, and LocalArea Connection Properties window will appear. Select “Internet
Protocol (TCP/IP)”, then click “Properties”.
1. Select “Obtain an IP address automatically” and “Obtain DNS server address
automatically”, then click “OK”.

http://www.sapido.com.tw/ User Manual 1.0
14
2.2.2 Windows XP
1. Click “Start” button (it should be located at lower-left corner of your computer), then
click control panel. Double-click Network and Internet Connections icon, click Network
Connections, then double-click Local Area Connection, Local Area Connection Status
window will appear, and then click “Properties”.
2. Select “Obtain an IP address automatically” and “Obtain DNS server address
automatically”, then click “OK”.

http://www.sapido.com.tw/ User Manual 1.0
15
2.2.3 Windows Vista / Windows 7
1. Click “Start” button (it should be located at lower-left corner of your computer), then
click control panel. Click View Network Status and Tasks, and then click Manage
Network Connections. Right-click Local Area Network, then select “Properties”. Local
Area Connection Properties window will appear, select “Internet Protocol Version 4
(TCP / IPv4)”, and then click “Properties”.
2. Select “Obtain an IP address automatically” and “Obtain DNS server address
automatically”, then click “OK”.

http://www.sapido.com.tw/ User Manual 1.0
16
2.3 Router IP Address Lookup
After the IP address setup was completed, please click “start” “run” at the bottom-lower
corner of your desktop:
Input “cmd”, and then click “OK”.

http://www.sapido.com.tw/ User Manual 1.0
17
Input “ipconfig”, then press “Enter” key. Please check the IP address followed by “Default
Gateway” (In this example, the gateway IP address of router is 192.168.1.1)
NOTE: If the IP address of Gateway is not displayed, or the address followed by ‘IP Address’ begins with
“169.x.x.x”, please recheck network connection between your computer and router, and / or go to the
beginning of this chapter, to recheck every step of network setup procedure.
2.3.1 Log into Web GUI
After obtained an IP address from wireless router, please start your web browser, and input
the IP address of the wireless router in address bar.
Notes: The default IP of the wireless router is 192.168.1.1

http://www.sapido.com.tw/ User Manual 1.0
18
Enter the User name and Password in to the blank and then Click Login. The default values
for User Name and Password are admin (all in lowercase letters).

http://www.sapido.com.tw/ User Manual 1.0
19
3. Internet Connection
This Chapter describes how to setup N+ Mobile 3G Modem Router to the internet. The 3G
mini router is delivered with the following factory default parameters.
Default IP address: 192.168.1.1
Default IP subnet mask: 255.255.255.0
Web login user name: admin
Web login password: admin
3.1 Plug and Play
The N+ Mobile 3G Modem Router supports three types of Internet connection: 3G/3.5G
modem card, wire or wireless connection via xDSL/Cable modem. Just connect the
3G/3.5G modem card or Ethernet cable to N+ Mobile 3G Modem Router , the router will
recognize it automatically.
3.2 Connect to Internet through web GUI
1. Open a Web browser, and enter http://192.168.1.1 (Default Gateway) into the blank.

http://www.sapido.com.tw/ User Manual 1.0
20
2. Enter the User name and Password in to the blank and then Click “Login”. The default
values for User Name and Password are admin (all in lowercase letters).