SAR Rope Lanyards User manual

Declaration Of Conformity
The EU Declaration of conformity is available by scanning the QR code or
visiting - www.sar-products.com/eu-doc/
Certificate Of Conformity
We certify that the SAR Rope Lanyards conform to EN354:2010
Other components used with this product must conform to the relevant EN standards. Conforms to:
EN354:2010
10.5mm 11mm 12mm
Product Record
This documentation should be issued with, and kept for, each item or system. Please see
the product label for the details required below. Consult this guide for advice on
inspection, maintenance, lifespan, etc.
Signature:…………………………………………………………… For SAR Products Ltd
Owner / User’s Name:
Inspection & Maintenance Record
Date & Time Type of Inspection & Comments
Date of Manufacture: Date of Purchase:
Date of First Used: Product Serial No.:
Name & Signature
of Inspector Next Inspection
Due
Specialist Access & Rescue
Products Ltd.
User Guide
Rope Lanyards
sar-products.com
[phone]
[email protected]
Specialist Access & Rescue Products Ltd.
Sarena House, Vulcan Street, Oldham, OL1 4LQ
[phone] [email protected] www.sar-products.com
Standard Y Shaped Cow’s Tail
Serial No.:
0598

Important:
Please read, study and understand these instructions
before use.
Use
The SAR Slings and lanyards have been designed for
your protection and therefore are (PPE) personal
protective equipment. It is a safety sling for rescue
and technical access (in normal climatic conditions).
Use only as instructed and with compatible items of
equipment. These should conform to the relevant
European standards or those your country follows.
Check that the safe function of any one component
within a system will not interfere with the safe
function of another. Twists in slings or lanyards can
cause problems and weakness in other components.
Neatness is strength.
Users should be trained, competent or under the
supervision of such a person.
Safety
The safety provided by this sling depends on its
strength, the anchor/belay and the skill of the user.
The strength will be reduced through age, wear and
tear, abrasion, cuts, high impact loads, tight/sharp
edges, knots, some chemical (e.g. alkalis,etc.), UV or
failure to store and maintain as recommended. This
list is not exhaustive. As a rule, but not always (so be
careful) if the sling has a high strength rating then
there is less chance of failure due to the points
outlined above; however, there are exceptions which
include chemical attack or very high temperatures. Do
not alter the product in any way. Any sling subjected
to a minor fall should be examined and discarded if
there is any sign of defect or any doubts about its
safety.
Anchorage
Anchor points should always be strong enough to
hold the user particularly in the event of a fall. They
should be at least 15kN. A webbing lanyard or rope
should be effectively sleeved to protect against
damage if structural members with sharp edges
cannot be avoided as anchorage points.
Anchor points, wherever possible, should be
above the user to limit any fall to less than the
length of the safety line or lanyard.
Lifespan
This is difficult to estimate but we advise as follows:
Do not use more than ten years after the date of
manufacture. Assuming you have used the correct
storage. The working life can vary between a single
use in extreme circumstances (e.g. highly chemical
environment, serious fall) to the maximum of ten
years, depending on how the product is used. The
working life will be reduced through age, general
wear and tear, abrasion, cuts, damage to component
parts, inappropriate ancillary equipment, high impact
load, prolonged exposure to UV light including
sunlight, elevated temperature (50°C max) exposure
to some chemicals (e.g. alkalis, etc.) or failure to store
and maintain as recommended. This list is not
exhaustive.
Inspection
Before each use visually inspect to ensure the product
is in serviceable condition and operates correctly. An
examination should be carried out at least every 6
months by a competent person authorised by the
manufacturer. These inspections should be recorded
paying particular attention to areas of potentially high
wear such as attachment points, buckles, connectors
and sewn joints. The materials Used in this product
are high spec Nylon & Polyester
Inspect as follows:
Textiles: Check for cuts, tears, and abrasions, damage
due to deterioration, contact with heat,
alkalis or other corrosives.
Sewing: Check for broken, cut or worn threads.
Metals: Check for cracks, distortion, corrosion, wear
by abrasion, burrs, worn or loose rivets or
screws, discolouration caused by extreme
heat (greater than 100°C) broken springs,
frays or cuts, seizure of moving parts,
broken or missing components.
Immediately withdraw from service any items
showing defects. The user’s life depends on it. All
repair work should be carried out by the
manufacturer or with their authorisation.
Maintenance
Always keep the product clean and dry. Any excess
moisture should be removed with a clean cloth and
then allowed to dry naturally in a warm room away
from direct heat.
(HVR) High Visibility Rope:
The reflective tracer on our High visibility rope is not
load bearing and does not affect the strength of the
rope. The reflective tracer may show signs of wear
when used in areas of high abrasion.
Meanings of markings
• The name, trademark or any other means of
identification provided by the manufacturer or
supplier.
• The batch or serial number
• The year of manufacture
• UKCA &/or CE mark with approved &/or notified
body number
• The British &/ or EN standard(s) to which the item
conforms
• Product description and/or reference
• Evaluation of capacity in kN
Strengths quoted are when the product is tested new
& are in accordance with the manufacturer test
methods or to the appropriate standard. Any weights
and measurements are approximate.
Nothing in this document affects the consumer’s
statutory rights.
Notified Body
SGS FIMKO OY, Takomotie 8, FI-00380 Helsinki, Finland.
Notified Body No: 0598
Approved Body UKCA
SGS United Kingdom Limited
Rossmore Business Park, Ellesmere Port, Cheshire,
CH65 3EN. Approved Body No: 0120
Cleaning
Rinse in clean cold water. If still soiled wash in clean
warm water (max. 40°C) with pure soap or a mild
detergent (within pH range of 5.5 to 8.5) You can use a
washing machine but first place the product in a
suitable bag to protect against mechanical damage.
Rinse properly in clean cold water.
Chemicals
Avoid contact with any chemicals which could affect
the performance of the product. If contact occurs or is
suspected then discard the product immediately. If
used in a marine environment thoroughly rinse in
clean cold water and dry after each use.
Storage
After cleaning, store unpacked in a cool, dry, dark
place away from excessive heat sources or other
possible causes of damage. Do not store wet. If a long
shelf life is required it is advisable to store in a
moisture proof package (e.g. polythene bag).
Warning
Working at height is hazardous. It is the user’s
responsibility to ensure understanding of the correct
and safe use of this equipment, to use it only for the
purposes for which it is designed and to practise all
proper safety procedures.
A lanyard shall not be used for fall arrest purposes
without any energy absorption. e.g. an energy
absorber.
The total length of a lanyard connected to an energy
absorber (including terminations and connectors)
shall not exceed 2m.
The information in this guide meets the requirements
of the PPE EU Regulations 2016/425. It is not
comprehensive and cannot be substituted for the
correct training, which can be provided if required. If
in any doubt please don’t hesitate to contact us.
Using the lanyards in the examples shown above are
dangerous and could have deadly consequences.
22Kn