Satel abax 2 ACD-220 User manual

Wireless curtain detector
ACD-220
Firmware version 1.00
acd-220_en 02/23
SATEL sp. z o.o. •ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
tel. [phone]
www.satel.pl
EN

IMPORTANT
The device should be installed by qualified personnel.
Prior to installation, please read carefully this manual.
Changes, modifications or repairs not authorized by the manufacturer shall void your rights
under the warranty.
The rating plate of the device is located on the enclosure base.
The device meets the requirements of the applicable EU directives.
The device is designed for indoor installation.
The device must not be disposed of with other municipal waste. It should be disposed of
in accordance with the existing rules for environment protection (the device was placed
on the market after 13 August 2005).
The device meets the technical regulations of the Eurasian Customs Union.
SATEL aims to continually improve the quality of its products, which may result in changes in
their technical specifications and software. Current information about the changes being
introduced is available on our website.
Please visit us at:
https://support.satel.pl
Hereby, SATEL sp. z o.o. declares that the radio equipment type ACD-220 is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity
is available at the following internet address: www.satel.pl/ce
In the EU, this radio equipment is only permitted to operate in the 868 MHz frequency
band.
The following symbols may be used in this manual:
- note,
- caution.

CONTENTS
1Features ...........................................................................................................................2
2Description........................................................................................................................2
Radio communication.......................................................................................................2
Alarms ..............................................................................................................................2
Operating modes..............................................................................................................2
Energy saving mode (ECO)..............................................................................................3
Test mode.........................................................................................................................3
LED...................................................................................................................................3
Supervision of motion detection system ...........................................................................3
Battery status control........................................................................................................3
3Electronics board..............................................................................................................3
4Selecting a mounting location...........................................................................................4
5Installation ........................................................................................................................4
6Specifications ...................................................................................................................6

2 ACD-220 SATEL
The ACD-220 detector detects motion in the protected area. Its coverage area is shaped like
a curtain which makes it suitable as a component of parameter protection. The detector is
designed for operation within the ABAX 2 two-way wireless system. It is supported by:
ACU-220 / ACU-280 controller with firmware version 6.03 (or newer),
ARU-200 repeater.
1 Features
Motion detection with passive infrared sensor (PIR).
Adjustable detection sensitivity.
Digital motion detection algorithm.
Digital temperature compensation.
Custom-designed lens for SATEL’s short-range curtain detectors.
Encrypted two-way radio communication in the 868 MHz /915 MHz frequency band (AES
standard).
Transmission channel diversity –4 channels for automatic selection of the one that will
enable transmission without interference with other signals in the 868 MHz /915 MHz
frequency band.
Remote update of detector firmware.
Remote configuration.
Built-in temperature sensor (temperature measurement range from -10°C to +55°C).
LED indicator.
Supervision of motion detection system.
“ECO” option for longer battery life.
Battery status control.
Tamper protection against enclosure opening and removal from mounting surface.
2 Description
Radio communication
The detector connects to the controller at regular time intervals to provide information about
its state (periodical communication). Additional communication may take place as a result of
alarm (see “Operating modes”).
Alarms
The detector will report alarm:
after detecting a motion in the protected area,
after detecting a fault in the motion detection system,
after opening the tamper switch (tamper alarm).
Operating modes
Active –information about tamper alarm and motion detection alarm is sent immediately.
Passive –only information about tamper alarm is sent immediately. This operating mode
extends the battery life.

SATEL ACD-220 3
The detector operating mode is enabled remotely. If the detector is used in the INTEGRA /
VERSA / PERFECTA 64 M alarm system, the operating mode may depend on the partition
state (partition disarmed –passive mode; partition armed –active mode). For more
information, refer to the ABAX 2 controller manual.
Energy saving mode (ECO)
If you want to extend the battery life, you can enable in the detector the “ECO” option.
When the “ECO” option is enabled, the periodical communication takes place every
3 minutes. This may provide up to four times longer battery life.
Test mode
The LED is enabled in the test mode which makes it easier to test the detector. For how to
enter and exit the test mode, see the ABAX 2 controller manual.
LED
The LED will flash for about 5 seconds after the battery is inserted to indicate warm-up of the
detector. The LED also works in the test mode, in which it indicates:
periodical communication –short flash (80 milliseconds),
alarm –ON for 2 seconds.
Supervision of motion detection system
When the motion detection system starts malfunctioning, the detector will report an alarm
during periodical communication. The alarm will keep going until the fault is cleared
(long violation).
Battery status control
When the battery voltage is below 2.75 V, information about low battery is sent during each
transmission.
In response to the battery voltage drop below 2.75 V, sensitivity of the IR sensor in the
detector is automatically lowered to eliminate false alarms.
3 Electronics board
Do not remove the electronics board from the enclosure to avoid damage to the
components on the board.
CR123A lithium battery.
tamper switch.
The PIR sensor (dual element pyrosensor) and the LED are placed on the other side of the
electronics board.

4 ACD-220 SATEL
4 Selecting a mounting location
Do not install the detector outdoors (A).
Do not point the detector towards heat sources (B), air conditioners (C) or fans (D).
Install the detector in a place where the expected direction of the intruder movement will
be across the coverage pattern (Fig. 2).
5 Installation
There is a danger of battery explosion when using a different battery than
recommended by the manufacturer, or handling the battery improperly. Do not
crush the battery, cut it or expose it to high temperatures (throw it into the fire,
put it in the oven, etc.).
Do not expose the battery to very low pressure due to the risk of battery
explosion or leakage of flammable liquid or gas.
Be particularly careful during installation and replacement of the battery.
The manufacturer is not liable for the consequences of incorrect installation of
the battery.
The used batteries must not be discarded, but should be disposed of in
accordance with the existing rules for environment protection.

SATEL ACD-220 5
1. Remove the detector cover (Fig. 3). The enclosure opening tool, shown in the illustration,
is included in the detector delivery set.
2. Insert the battery and add the detector to the wireless system (see the ABAX 2 controller
manual). The sticker with serial number which shall be entered when registering the
detector in the system can be found on the electronics board.
In the VERSA alarm system, you can add and configure the ACD-220 detector only by
using the DLOADX program.
3. Replace the detector cover.
4. Place the detector at its future mounting location.
5. Check the level of signal received from the detector by the ABAX 2 controller. If the signal
level is lower than 40%, select another mounting location. Sometimes, it is sufficient to
shift the device ten or twenty centimeters.
You can use the ARF-200 tester to test the radio signal strength at the future mounting
location without having the detector physically there.
6. Remove the detector cover (Fig. 3).
7. Use wall plugs (anchors) and screws to mount the enclosure base to the surface (Fig. 4).
The wall plugs delivered with the device are intended for concrete, brick, etc. For other
types of surface (drywall, styrofoam), use the appropriately selected wall plugs.
8. Replace the detector cover.
9. Configure the detector settings (sensitivity of IR sensor etc. –see the ABAX 2 controller
manual).
10.Enable the test mode (see the ABAX 2 controller manual).
11.Check whether moving around within the detector coverage area will make the LED
light up. Fig. 5 shows the maximum coverage area.
12.Exit the test mode.

6 ACD-220 SATEL
6 Specifications
Operating frequency band................................868,0 MHz ÷868,6 MHz / 915 MHz –928 MHz
Radio communication range (in open area)
ACU-220.......................................................................................................up to 2000 m
ACU-280.......................................................................................................up to 1200 m
Battery....................................................................................................................CR123A 3 V
Battery life expectancy..........................................................................................up to 2 years
Temperature measurement range .......................................................................-10°C...+55°C
Temperature measurement accuracy ................................................................................±1°C
Standby current consumption .......................................................................................... 70 µA
Maximum current consumption........................................................................................15 mA
Detectable speed......................................................................................................0.3...1 m/s
Warm-up period....................................................................................................................5 s
Coverage area....................................................................................................5 m x 1 m, 15°
Complied with standards....................................................................EN 50130-4, EN 50130-5
Environmental class according to EN 50130-5 ........................................................................II
Operating temperature range...............................................................................-10°C...+55°C
Maximum humidity..........................................................................................................93
±
3%
Dimensions................................................................................................... 20 x 102 x 25 mm
Weight.................................................................................................................................43 g