Satel ABAX 2 APD-200 User manual

Wireless passive infrared detector
APD-200
Firmware version 1.00
apd-200_en 02/23
SATEL sp. z o.o. •ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
tel. [phone]
www.satel.pl
EN

IMPORTANT
The device should be installed by qualified personnel.
Prior to installation, please read carefully this manual.
Changes, modifications or repairs not authorized by the manufacturer shall void your rights
under the warranty.
The rating plate of the device is located on the enclosure base.
The device meets the requirements of the applicable EU directives.
The device is designed for indoor installation.
The device must not be disposed of with other municipal waste. It should be disposed of
in accordance with the existing rules for environment protection (the device was placed
on the market after 13 August 2005).
The device meets the technical regulations of the Eurasian Customs Union.
SATEL aims to continually improve the quality of its products, which may result in changes in
their technical specifications and software. Current information about the changes being
introduced is available on our website.
Please visit us at:
https://support.satel.pl
Hereby, SATEL sp. z o.o. declares that the radio equipment type APD-200 is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity
is available at the following internet address: www.satel.pl/ce
In the EU, this radio equipment is only permitted to operate in the 868 MHz frequency
band.
The following symbols may be used in this manual:
- note,
- caution.

CONTENTS
1Features ...........................................................................................................................2
2Specifications ...................................................................................................................2
3Description........................................................................................................................3
Radio communication.......................................................................................................3
Alarms ..............................................................................................................................3
Operating modes..............................................................................................................3
Energy saving mode (ECO)..............................................................................................3
Test mode.........................................................................................................................4
LEDs.................................................................................................................................4
Supervision of motion detection system ...........................................................................4
Battery status control........................................................................................................4
Electronics module ...........................................................................................................4
4Installation ........................................................................................................................4

2 APD-200 SATEL
The APD-200 detector is used to detect motion in a protected area. It is designed for
operation within the ABAX 2 / ABAX two-way wireless system. This manual applies to the
detector with firmware version 1.00 (or newer), which is supported by:
ABAX 2:
–ACU-220 / ACU-280 controller,
–ARU-200 repeater.
ABAX:
–ACU-120 / ACU-270 controller (firmware version 5.04 or newer),
–ARU-100 repeater (firmware version 2.02 or newer),
–INTEGRA 128-WRL control panel (firmware version 1.19 or newer and firmware
version of processor used to operate ABAX system 3.10 or newer).
1 Features
Motion detection with passive infrared sensor (PIR).
Digital motion detection algorithm.
Digital temperature compensation.
Option to enable / disable the creep zone protection.
Ability to replace the lens with a curtain or long-range one.
Encrypted two-way radio communication in the 868 MHz / 915 MHz frequency band (AES
standard for the ABAX 2 system).
Transmission channel diversity –4 channels for automatic selection of the one that will
enable transmission without interference with other signals in the 868 MHz / 915 MHz
frequency band (ABAX 2 system only).
Remote update of detector firmware (ABAX 2 system only).
Remote configuration.
Built-in temperature sensor (temperature measurement range from -10°C to +55°C).
LED indicators.
Supervision of motion detection system.
“ECO” option for longer battery life (ABAX 2 system only).
Battery status control.
Tamper protection against enclosure opening and removal from mounting surface.
Adjustable mounting bracket included.
2 Specifications
Operating frequency band................................868.0 MHz ÷868.6 MHz / 915 MHz –928 MHz
Radio communication range (in open area)
ABAX 2
ACU-220 ..............................................................................................up to 2000 m
ACU-280 ..............................................................................................up to 1600 m
ABAX..............................................................................................................up to 500 m
Battery....................................................................................................................CR123A 3 V
Battery life expectancy..........................................................................................up to 2 years
Temperature measurement range .......................................................................-10°C...+55°C

SATEL APD-200 3
Temperature measurement accuracy................................................................................±1°C
Standby current consumption...........................................................................................70 µA
Maximum current consumption........................................................................................12 mA
Detectable speed...................................................................................................... 0.3...3 m/s
Warm-up period.................................................................................................................. 35 s
Recommended installation height............................................................................2 m...2.4 m
Coverage area................................................................................................15 m x 24 m, 90°
Complied with standards..................................................EN50131-1, EN50130-4, EN50130-5
Security grade according to EN50131-2-2 (detector mounted directly to the wall) .......Grade 2
Environmental class according to EN50130-5.........................................................................II
Operating temperature range...............................................................................-10°C...+55°C
Maximum humidity..........................................................................................................93
±
3%
Dimensions....................................................................................................62 x 137 x 42 mm
Weight...............................................................................................................................132 g
3 Description
Radio communication
The detector connects to the controller / control panel at regular time intervals to provide
information about its state (periodical communication). Additional communication may take
place as a result of alarm (see “Operating modes”).
Alarms
The detector will report alarm:
after detecting a motion in the protected area,
after detecting a fault in the motion detection system,
after opening the tamper switch (tamper alarm).
Operating modes
Active –information about tamper alarm and motion detection alarm is sent immediately.
Passive –only information about tamper alarm is sent immediately. This operating mode
prolongs the battery life.
The detector operating mode is turned on remotely. If the detector is used in the INTEGRA /
VERSA / PERFECTA 64 M alarm system, the operating mode may depend on the partition
state (partition disarmed –passive mode; partition armed –active mode). For more
information, refer to the ABAX 2 / ABAX controller manual / the INTEGRA 128-WRL control
panel manual.
Energy saving mode (ECO)
If you want to prolong the battery life, you can enable in the detector the “ECO” option.
When the “ECO” option is enabled, the periodical communication takes place every
3 minutes. Thus the battery life can be increased as much as fourfold. The option is only
available in the ABAX 2 system. The detector with “ECO” option enabled meets requirements
of the EN50131-2-2 standard for Grade 2.

4 APD-200 SATEL
Test mode
The test mode makes the detector testing easier, because the LED indicators are enabled.
How to start and end the test mode is described in the ABAX 2 / ABAX controller manual /
the INTEGRA 128-WRL control panel manual.
LEDs
The LEDs are flashing for about 35 seconds from inserting the battery, thus signaling the
warm-up of the detector. The LEDs also work in the test mode, in which they indicates:
periodical communication –short flash (80 milliseconds),
alarm –ON for 2 seconds.
Supervision of motion detection system
When the motion detection system starts malfunctioning, the detector will report an alarm
during periodical communication. The alarm will keep going until the fault is cleared (long
violation).
Battery status control
When the battery voltage is below 2.75 V, information about low battery is sent during each
transmission.
In response to the battery voltage drop below 2.75 V, sensitivity of the IR sensor in the
detector is automatically lowered to eliminate false alarms.
Electronics module
Do not remove the plastic cover from
the circuit board to prevent damage to
the components located on the board.
Do not touch the pyroelectric sensor,
so as not to soil it.
CR123A lithium battery.
LED indicator.
element not used.
tamper switch activated by cover removal.
PIR sensor (dual element pyrosensor).
On the other side of the electronics module is
a tamper switch activated by removing the
detector from the wall.
4 Installation
There is a danger of battery explosion when using a different battery than
recommended by the manufacturer, or handling the battery improperly. Do not
crush the battery, cut it or expose it to high temperatures (throw it into the fire,
put it in the oven, etc.).

SATEL APD-200 5
Do not expose the battery to very low pressure due to the risk of battery
explosion or leakage of flammable liquid or gas.
Be particularly careful during installation and replacement of the battery.
The manufacturer is not liable for the consequences of incorrect installation of
the battery.
The used batteries must not be discarded, but should be disposed of in
accordance with the existing rules for environment protection.
1. Remove the front cover (Fig. 2).
2. Move the electronics module down to unlock it, and then remove it from the enclosure
base (Fig. 3).

6 APD-200 SATEL
3. Install the battery and add the detector to the wireless system (see the ABAX 2 / ABAX
controller manual or the INTEGRA 128-WRL control panel installer manual). The sticker
with serial number which shall be entered when registering the detector in the system can
be found on the electronics module.
In the INTEGRA / VERSA alarm system, the detector is identified as APD-100.
Simultaneous operation of the detector by the ABAX 2 and ABAX controller /
INTEGRA 128-WRL alarm control panel is not possible.
4. Place the electronics module in the enclosure base and then move it up to lock it.
5. Replace the cover.
6. Put the detector at the place of its future installation.
7. Check the level of signal received from the detector by the ABAX 2 / ABAX controller or
the INTEGRA 128-WRL control panel. If the signal level is lower than 40%, select another
place for installation. Sometimes, it is sufficient to shift the device ten or twenty
centimeters.
The ARF-200 tester makes it possible to check the radio signal strength at the place of
future installation without having to put the detector there.
8. Remove the front cover (Fig. 2) and remove the electronics module (Fig. 3).
9. Make screw holes in the enclosure base.

SATEL APD-200 7
10.Secure the enclosure base to the wall (Fig. 4) or the bracket fastened with screws to the
wall or ceiling (Fig. 5). The wall plugs (anchors) delivered with the device are intended for
concrete, brick, etc. For other types of surface (drywall, styrofoam), use the appropriately
selected wall plugs.
If the detector is to comply with the EN50131-2-2 requirements for Grade 2, do not
install it on the mounting bracket (if installed on the bracket, the detector will comply
with the standard requirements for Grade 1).

8 APD-200 SATEL
11.Fasten the electronics module in the enclosure.
12.If the detector is to protect the creep zone, the knob located on the inner side of the
enclosure cover is to be set in position shown in Fig. 6-A. If the detector is NOT to protect
the creep zone, set the knob to the position shown in Fig. 6-B.
13.Replace the cover.
14.Configure the detector settings (sensitivity of PIR sensor, etc. –see the ABAX 2 / ABAX
controller manual / the INTEGRA 128-WRL control panel manual).

SATEL APD-200 9
15.Start the test mode (see the ABAX 2 / ABAX controller manual / the INTEGRA 128-WRL
control panel manual).

10 APD-200 SATEL
16.Check whether moving around within the detector coverage area will get the LEDs to
come on. Fig. 7 shows the maximum detection range and the creep zone of
a detector placed at a height of 2.4 m.
Fig. 7 shows the range of APD-200 detector with the wide-angle (WD) Fresnel lens,
which is installed in the detector as standard one. You can change the detector
enclosure cover to install another lens instead. The SATEL product range includes
covers with the curtain (CT) lens as well as with the long-range (LR) lens.
17.End the test mode.