Scantronic 601 User manual

601/602 USER GUIDE
TO FULL SET
Key in your user code. The Armed light
flashes and the exit tone starts. Leave
the premises by the designated exit
route.
The exit tone stops after a preset time
and the Armed light glows steadily.
The alarm system is then set.
TO PART SET
To set your alarm system so that you
can move around part of the area nor-
mally covered by detectors:
Key in 2 + ENTER followed by your
security code. The Armed light flashes
slowly. Leave the protected area. After
a preset time the panel gives a double
bleep. The system is now part set.
Note: The installer may have disabled
the part set facility. Contact them if
you have any difficulty.
TO OMIT A ZONE
Key in your user code, followed by
OMIT and the zone number within five
seconds. The Armed light and the zone
light to be omitted flash, and the exit
tone starts. Leave the premises. After a
pre-set time the exit tone stops and
the Armed light glows steadily. The
system is now set with an omitted
zone.
CHIME
Key in 7 + ENTER followed by your
user code. The panel gives a two tone
bleep. While chime is on, the panel
gives a two tone bleep every time a
detector is triggered. Note: The installer
may not have programmed every
detector to trigger a chime.
To switch Chime off: key in 7 + ENTER
followed by your user code.
TO SWITCH OFF
Enter by the designated entry route.
The entry tone starts. Go to the control
panel and key in your four digit user
code. The Armed light goes out. The
system is unset.
PANIC ALARM
Press 1 and 3 at the same time. The
panel does not give any indication of
an alarm.
= four digit user code
()
Leave by
designated
route
ENTER
OMIT
ZONE
NUMBER
OMIT
ZONE
NUMBER
FOR OTHER
ZONES
()
ENTER
Enter by
designated
route
Go to
panel
Service Telephone No:
Part No: 496181 Issue 1
Intelligent Security & Fire Ltd

TO RESET AFTER AN ALARM
The panel sounds the alarm by giving a
siren tone from its internal sounder,
and triggering the external bell and
strobe (if you have one).
Go to the panel and key in your user
code. The panel stops the tone and
switches off the external bell/strobe. A
flashing zone light indicates the cause
of the alarm.
To reset system: Enter your user code
again. The flashing zone light goes out.
If the system does not go to reset, call
the installer.
Tamper Alarm: If the panel gives an
internal alarm while unarmed then go
to the control panel and key in your
user code to stop the sounder. The
Tamper light flashes. Call the installer
for service.
TO READ THE LOG
Your alarm system keeps a record of
the last 15 alarm events.
Key in 5 + ENTER followed by your
user code. The panel lights show the
last event.
Press 4 repeatedly to see earlier alarms.
Press 6 repeatedly to see more recent
alarms. The panel gives a low tone
when you reach the end of the log.
Press ENTER at any time to leave the
log.
TO CHANGE YOUR USER CODES
You can have up to eight user codes
and one duress code. Each code can be
any four digit number not starting with
0 (zero). Key in 4 + ENTER followed by
your user code. Key in the existing user
code that you want to change. The
panel gives a double bleep. Key in the
new user code. The panel gives a dou-
ble bleep when it accepts the new
code. If you hear a single low bleep the
panel did not accept the new code. Try
again from the beginning.
TO WALK TEST THE DETECTORS
Key in 9 + ENTER followed by your
user code.
Activate each detector in turn. The
panel gives a two tone bleep and lights
the corresponding zone when it
receives a signal from a detector. To
end the test press ENTER.
TO TEST BELLS
Key in 8 + ENTER followed by your
user code. The panel sounds the exter-
nal bell, strobe, and internal sounder
for three seconds each.
Check the premises
ENTER
ENTER
new user codeexisting code
ENTER
ENTER
ENTER
ENTER
Walk past
detectors
Note: The default code for user one is
‘1234’. The default for user two is
‘0001’, user three is ‘0002’ and so on
up to user 8, which is ‘0007’.
Intelligent Security & Fire Ltd