Scantronic 760ES User manual

PAK200474_01E August 2008 Page 1 of 4
760ES Radio Siren Installation Guide
Overview
The 760ES is an external, self powered, siren and strobe unit designed to work with the
i-on range of control units.
Fitted within the enclosure are twin sounders capable of exceeding 100dB(A), a radio
transceiver operating on 868MHz, a battery pack and a LED strobe strip. The unit can be
mounted on any non-metallic vertical surface. The range of operation from the control unit
may vary depending on the site conditions and in particular the material of walls between
the two units. In free air the range will easily exceed 100m.
This product is suitable for use in systems designed to comply with EN 50131-1:2006 and
PD6662:2004 +A1+A2 at Grade 2 and is tested to prEN 50131-4:2008 at Grade 2.
Lens
Spirit Level
Cove
r
Screw Cover
Battery
Connecto
r
Battery pack
Main PCB
Fixing screws
parking
Piezo sounde
r
Tamper
extender pin
LED Strobe
strip Cover tamper detector
Backplate Wall fixing
points
Features
•105 dB(A)@1m sound output
•prEN 50131-4 Grade 2 Compliant
•High power LED strobe
•Cover and rear tamper detection
•Selectable cut-off timer
•Anti-jamming detection
•Conformally coated electronics
•Battery change warning
•Built in spirit level installation aid
•Choice of battery options
•Quiet installation mode
•Cover screen printing facility
•High impact resistant polycarbonate
backplate and cover
Technical Specification
Sound Output 105 dBA@1m (tone)
Cut-off Timer Selectable 5 secs, 3 mins, 15 mins
Environmental EN 50130-5:1999 class IV
Operating temperature -25°C to +60°C
Humidity 93% RH
Dimensions 212mm W, 346mm H, 76mm D
Weight 1.2 kg (without batteries)
Case material Polycarbonate

760ES
PAK200474_01E August 2008 Page 2 of 4
Radio Supervision Programmable at control unit.
Radio Section Operating frequency 868.6625MHz Narrowband.
Transmitter range 100m depending on the installation environment.
Battery Packs 2 x 3V Alkaline or 1 x 7.2V Lithium*
Battery Life Over two years for typical use*
Monitoring includes Battery low voltage (<4.0V), RF Jamming.
*Lithium batteries are recommended if temperatures are regularly below 0°C.
Compliance, EMC and Safety
This product complies with the following EU Directives:
R&TTE 1999/5/EC, EMC: 2004/108/EC, RoHS: 2002/95/EC, WEEE: 2002/96/EC
Configuration
At the siren Key:
Link FITTED Link NOT Fitted
Jamming detected signal transmission ON: OFF:
•The siren independently monitors for attempted jamming but does
not self activate.
Jamming On = Siren informs control unit (Default)
Jamming Off = No action
Tamper Self-Activation (SAB) Mode ON: OFF:
•SAB On = Siren self triggers when tampered and informs control
unit, stops when tamper switch closed, or stopped by control unit.
(Default)
•SAB Off = Siren does not self trigger but informs control unit when
tampered. Control unit makes decisions.
Sounder automatic cut-off timer 3 mins 15 mins 5 secs
Siren will stop when commanded by the control unit or after
the cut-off time selected by the position of the link. Default is
15 minutes. The strobe is not affected by the cut-off (it stops
after a maximum of 15 minutes)
At the control unit
The siren can show that setting or unsetting has finished by flashing of the strobe. Refer
to the i-on Installation and Programming Guide for details.
Installation
Carry out a radio site survey using the 790r signal strength meter and test transmitter to
check that reception is adequate at the proposed sites for the control unit and siren.
Site the siren:
a) Upright (strobe at the bottom), with space around it to permit good radio reception.
b) Out of reach of intruders or vandals.
c) Where it can be seen and heard easily.
Do NOT site the siren:
a) Within 1m of large metal structures, for example: metal doors or frames, water tanks,
cars, fridges and freezers.
b) Within 1m of mains wiring or metal water or gas pipes.
c) Inside metal enclosures.
d) Next to high voltage electrical or electronic equipment, particularly computers,
photocopiers or other radios.

760ES
PAK200474_01E August 2008 Page 3 of 4
WARNING
When installing batteries in the siren it may momentarily emit a loud tone. This
may startle you. Ensure that you cannot overbalance and fall, or drop the siren.
Opening the siren and fitting/removing batteries:
1. Rotate the screw covers to access the two cover retaining
screws. Undo the cover retaining screws far enough to
release the cover.
2. Hinge the cover upwards from the bottom and remove it.
3. Slide the two alkaline (3V) or single lithium (7.2V) battery
pack(s) from the side into the battery holding area. Use the
clips provided to retain the battery cables. Ensure the
cables are fitted the correct way around.
4. Push the connectors on to the pins on the PCB.
CAUTION: Take care to use the correct connections to avoid
damaging the batteries or siren.
5. To remove the batteries first unplug the connectors from
the PCB and remove the cables from the clips. Then push
on the flexible parts of the backplate to allow the batteries
to slide out of their holders.
6. At the end of the product’s life, the batteries must be
removed from the product. Both the waste product and
batteries must be separated from the domestic waste
stream and disposed of via an appropriate approved WEEE
disposal route in accordance with all national and local
regulations.
Replacement Battery Part Nos.:
3V Alkaline: 760AB 7.2V Lithium: 760LB
Teaching the Siren to the Control Unit
You must “teach” the identity of the siren to the control
unit. For instructions see the i-on installation guide.
For “teaching”, put the i-on into “installer mode”, insert
and connect the batteries (see above) and then operate
the tamper detection switch at the bottom or back of the
siren.
When attaching the cover make sure that you fit the
tamper switch spring correctly (see right)
Note: Do not leave installer mode until you have fitted the siren in its final position. While
in installer mode the siren will sound only in response to a test command. The siren

760ES
PAK200474_01E August 2008 Page 4 of 4
becomes fully active when you leave installer mode and depending on configuration may
sound when a tamper switch is activated.
Physical Installation
Attach the siren to a solid non-metallic wall using
suitable screws and wall fixing plugs. The fixing
points are located in the four corners of the
backplate.
To assist with levelling the siren there is a spirit
level in the upper part (Item 8 on diagram).
Fit rear tamper extender (if required) and trim to
desired length (see below).
Maintenance
Test the sounder and strobe periodically for correct operation . During routine
maintenance check the correct operation of cover and rear tampers. Check for signs of
significant water or insect ingress and clean as necessary. Replace batteries every two
years or when advised by the control unit.
Fault finding and diagnostics
The siren informs the control unit if its batteries have low voltage. The siren continues to
self-actuate under tamper conditions even when radio communications to the control unit
have been lost because of low battery voltage.
After installing, the siren will not sound until the control unit has left installer mode.
Changes in the environment (or deliberate jamming) may prevent radio transmission
between the siren and control unit. The siren will try to inform the control unit when
jamming is detected only if this feature is enabled using the configuration link.
The packaging supplied with this product may be recycled.
Please dispose of packaging accordingly.
Cooper Security Ltd
Security House
Vantage Point Business Village
Mitcheldean
Gloucestershire
GL17 0SZ
www.coopersecurity.co.uk
Product Support (UK) Tel: [phone].
Available between:
08:15 and 17:00 Monday to Friday.Product Support Fax: [phone]