Schumacher Electric MC-1 User manual

00-99-001017-1109
Model / Modelo / Modèle: MC-1 & MCF-1
Manual Battery Charger / Cargador de Batería Manual /
Chargeur de Batterie Manuel
Voltage / Tensión / Tension: 6, 12
Amperage / Amperaje / Ampérage: 1
READ THE ENTIRE MANUAL BEFORE USING THIS PRODUCT.•
FAILURE TO DO SO CAN RESULT IN SERIOUS INJURY OR DEATH.
LEA EL MANUAL COMPLETO ANTES DE UTILIZAR ESTE PRODUCTO.•
CUALQUIER FALLA PODRÍA RESULTAR EN SERIAS LESIONES O PODRÍA
SER MORTAL.
LIRE ENTIÈREMENT LE GUIDE AVANTD’UTILISER CE PRODUIT.•
L’ÉCHEC DE FAIRE AINSI PEUT S’ENSUIVRE DANS LA BLESSURE
SÉRIEUSE OU LA MORT.
OWNER’S MANUAL•
MANUAL DEL USUARIO•
GUIDE D’UTILISATION•

TABLE OF CONTENTS
SECTION PAGE
1. IMPORTANT SAFETY INSTRUCTIONS 2
2. PERSONAL PRECAUTIONS 3
3. PREPARING TO CHARGE 3
4. CHARGER LOCATION 4
5. DC CONNECTION PRECAUTIONS 5
6. FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE. 5
7. FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE. 6
8. BATTERY CHARGING – AC CONNECTIONS 6
9. FEATURES 7
10. ASSEMBLY INSTRUCTIONS 7
11. CONTROL PANEL 8
12. OPERATING INSTRUCTIONS 8
13. CALCULATING CHARGE TIME 9
14. MAINTENANCE INSTRUCTIONS 10
15. STORAGE INSTRUCTIONS 10
16. TROUBLESHOOTING 11
17. BEFORE RETURNING FOR REPAIRS 12
18. SPECIFICATIONS 13
19. REPLACEMENT PARTS 13
20. LIMITED WARRANTY 13

ÍNDICE
SECCIÓN PÀGINA
1. INSTRUCCIONES IMPORTANTES DE SEGURIDAD 16
2. PRECAUCIONES PERSONALES 17
3. PREPARACIÓN PARA LA CARGA 18
4. UBICACIÓN DEL CARGADOR 19
5. PRECAUCIONES DE CONEXIÓN EN CC 19
6. SIGA ESTOS PASOS CUANDO LA BATERÍA ESTÉ COLOCADA
EN EL VEHÍCULO. 20
7. SIGA ESTOS PASOS CUANDO LA BATERÍA SE ENCUENTRE
FUERA DEL VEHÍCULO. 21
8. CARGA DE BATERÍA, CONEXIONES DE CA 21
9. CARACTERÍSTICAS 22
10. INSTRUCCIONES DE MONTAJE 22
11. PANEL DE CONTROL 23
12. INSTRUCCIONES DE OPERACIÓN 23
13. CÁLCULO DE TIEMPO DE CARGA 24
14. INSTRUCCIONES DE MANTENIMIENTO 25
15. INSTRUCCIONES DE ALMACENAJE 25
16. LOCALIZACIÓN Y SOLUCIÓN DE PROBLEMAS 26
17. ANTES DE DEVOLVER A REPARACIONES 28
18. ESPECIFICACIONES 28
19. REPUESTOS 29
20. GARANTÍA LIMITADA 29

TABLE DES MATIÈRES
PARTIE PAGE
1. CONSIGNES DE SÉCURITÉ IMPORTANTES 32
2. PRÉCAUTIONS PERSONNELLES 33
3. PRÉPARATION POUR LE CHARGEMENT 33
4. EMPLACEMENT DU CHARGEUR 35
5. PRÉCAUTIONS SUR LA CONNEXION C.C. 35
6 ÉTAPES À SUIVRE QUAND LA BATTERIE EST INSTALLÉE
DANS UN VÉHICULE. 35
7. ÉTAPES À SUIVRE QUAND LA BATTERIE EST INSTALLÉE
HORS DU VÉHICULE. 36
8. CHARGEMENT D’UNE BATTERIE – RACCORDEMENTS C.A. 37
9. CARACTÉRISTIQUES 38
10. DIRECTIVES DE MONTAGE 38
11. PANNEAU DE CONTRÔLE 38
12. CONSIGNES D’UTILISATION 39
13. CALCUL DU TEMPS DE CHARGEMENT 40
14. CONSIGNES D’ENTRETIEN 41
15. DIRECTIVES D’ENTREPOSAGE 41
16. TABLEAU DE DÉPANNAGE 42
17. AVANT DE L’ENVOYER POUR RÉPARATION 44
18. CARACTÉRISTIQUES 44
19. PIÈCES DE RECHANGE 44
20. GARANTIE LIMITÉE 44

1
IMPORTANT: READ AND SAVE THIS SAFETY AND INSTRUCTION MANUAL.
SAVE THESE INSTRUCTIONS – The MC-1 and MCF-1 offer a wide range of
features to accommodate your needs. This manual will show you how to use
your charger safely and effectively. Please read, understand and follow these
instructions and precautions carefully, as this manual contains important safety
and operating instructions. The safety messages used throughout this manual
contain a signal word, a message and an icon.
The signal word indicates the level of the hazard in a situation.
Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury to the operator or bystanders.
Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury to the operator or
bystanders.
Indicates a potentially hazardous situation which, if not avoided,
could result in moderate or minor injury to the operator or
bystanders.
Indicates a potentially hazardous situation which, if not avoided,
could result in damage to the equipment or vehicle or property
damage.
Safety messages in this manual contain two different type styles.
Unnumbered type states the hazard.•
Numbered type states how to avoid the hazard.•
The icon gives a graphical description of the potential hazard.
Pursuant to California Proposition 65, this product contains chemicals
known to the State of California to cause cancer and birth defects or
other reproductive harm.

2
IMPORTANT SAFETY INSTRUCTIONS1.
Riskofelectricshockorre.
Do not expose the charger to rain or snow.1.1
Use only recommended attachments. Use of an attachment not recommended1.2
orsoldbySchumacher®ElectricCorporationmayresultinariskofre,
electric shock or injury to persons or damage to property.
To reduce the risk of damage to the electric plug or cord, pull by the plug1.3
rather than the cord when disconnecting the charger.
An extension cord should not be used unless absolutely necessary. Use of an1.4
improperextensioncordcouldresultinariskofreandelectricshock.Ifan
extension cord must be used, make sure:
That the pins on the plug of the extension cord are the same size and shape•
as those of the plug on the charger.
That the extension cord is properly wired and in good electrical condition.•
That the wire size is large enough for the AC ampere rating of the charger as•
speciedinSection8.
To reduce the risk of electric shock, unplug the charger from the outlet before1.5
attempting any maintenance or cleaning.
Remove personal metal items such as rings, bracelets, necklaces and1.6
watches when working with a lead-acid battery. A lead-acid battery can
produce a short-circuit current high enough to weld a ring or the like to metal,
causing a severe burn.
Donotoperatethechargerwithadamagedcordorplug;takeittoaqualied1.7
service person. (Call customer service at: 1-800-621-5485.)
Do not operate the charger if it has received a sharp blow, been dropped or1.8
otherwisedamagedinanyway;takeittoaqualiedserviceperson.(Call
customer service at: 1-800-621-5485.)
Donotdisassemblethecharger;takeittoaqualiedservicepersonwhen1.9
serviceorrepairisrequired.Incorrectreassemblymayresultinariskofreor
electric shock. (Call customer service at: 1-800-621-5485.)

3
PERSONAL PRECAUTIONS2.
Risk of explosive gases.
Working in the vicinity of a lead-acid battery is dangerous. Batteries generate2.1
explosive gases during normal battery operation. For this reason, it is of
utmost importance that you follow the instructions each time you use the
charger.
To reduce the risk of a battery explosion, follow these instructions and those2.2
published by the battery manufacturer and the manufacturer of any equipment
you intend to use in the vicinity of the battery. Review the cautionary markings
on these products and on the engine.
NEVERsmokeorallowasparkorameinthevicinityofabatteryorengine.2.3
Be extra cautious to reduce the risk of dropping a metal tool onto the battery.2.4
It might spark or short-circuit the battery or other electrical part that may cause
an explosion.
Use this charger for charging LEAD-ACID batteries only. It is not intended to2.5
supply power to a low voltage electrical system other than in a starter-motor
application. Do not use this battery charger for charging dry-cell batteries that
are commonly used with home appliances. These batteries may burst and
cause injury to persons and damage to property.
NEVER charge a frozen battery.2.6
NEVER overcharge a battery.2.7
PREPARING TO CHARGE3.
Risk of contact with battery acid. Battery acid is a
highly corrosive sulfuric acid.
Consider having someone close enough by to come to your aid when you3.1
work near a lead-acid battery.
Have plenty of fresh water and soap nearby in case battery acid contacts your3.2
skin, clothing or eyes.
Wear complete eye and body protection, including safety goggles and3.3
protective clothing. Avoid touching your eyes while working near the battery.

4
If battery acid contacts your skin or clothing, immediately wash the area with3.4
soapandwater.Ifacidentersyoureye,immediatelyoodtheeyewithcold
running water for at least 10 minutes and get medical attention right away.
If it is necessary to remove the battery from the vehicle to charge it, always3.5
removethegroundedterminalrst.Makesurealloftheaccessoriesinthe
vehicle are off to prevent arcing.
Be sure the area around the battery is well ventilated while the battery is being3.6
charged.
Clean the battery terminals before charging the battery. During cleaning, keep3.7
airborne corrosion from coming into contact with your eyes, nose and mouth.
Use baking soda and water to neutralize the battery acid and help eliminate
airborne corrosion. Do not touch your eyes, nose or mouth.
Add distilled water to each cell until the battery acid reaches the level3.8
speciedbythebatterymanufacturer.Donotoverll.Forabatterywithout
removable cell caps, such as valve regulated lead acid batteries (VRLA),
carefully follow the manufacturer’s recharging instructions.
Read, understand and follow all instructions for the charger, battery, vehicle3.9
and any equipment used near the battery and charger. Study all of the battery
manufacturer’sspecicprecautionswhilechargingandrecommendedrates
of charge.
Determine the voltage of the battery by referring to the vehicle owner’s manual3.10
and make sure that the output voltage of the charger is the correct voltage.
Make sure that the charger cable clips make tight connections.3.11
CHARGER LOCATION4.
Risk of explosion and contact with
battery acid.
Locate the charger as far away from the battery as the DC cables permit.4.1
Never place the charger directly above the battery being charged; gases from4.2
the battery will corrode and damage the charger.
Do not set the battery on top of the charger.4.3
Never allow battery acid to drip onto the charger when reading the electrolyte4.4
specicgravityorllingthebattery.
Do not operate the charger in a closed-in area or restrict the ventilation in any4.5
way.

5
DC CONNECTION PRECAUTIONS5.
Connect and disconnect the DC output clips only after setting all of the5.1
charger switches to the “off” position and removing the AC plug from the
electrical outlet. Never allow the clips to touch each other.
Attach the clips to the battery and chassis, as indicated in steps 6.5, 6.6, 7.2,5.2
7.3 and 7.4.
FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN6.
VEHICLE.
A spark near the battery may cause a
battery explosion. To reduce the risk
of a spark near the battery:
Position the AC and DC cables to reduce the risk of damage by the hood, door6.1
and moving or hot engine parts. NOTE: If it is necessary to close the hood
during the charging process, ensure that the hood does not touch the metal
part of the battery clips or cut the insulation of the cables.
Stay clear of fan blades, belts, pulleys and other parts that can cause injury.6.2
Check the polarity of the battery posts. The POSITIVE (POS, P, +) battery6.3
post usually has a larger diameter then the NEGATIVE (NEG, N, -) post.
Determine which post of the battery is grounded (connected) to the chassis.6.4
If the negative post is grounded to the chassis (as in most vehicles), see step
6.5. If the positive post is grounded to the chassis, see step 6.6.
For a negative-grounded vehicle, connect the POSITIVE (RED) clip from the6.5
battery charger to the POSITIVE (POS, P, +) ungrounded post of the battery.
Connect the NEGATIVE (BLACK) clip to the vehicle chassis or engine block
away from the battery. Do not connect the clip to the carburetor, fuel lines or
sheet-metal body parts. Connect to a heavy gauge metal part of the frame or
engine block.
For a positive-grounded vehicle, connect the NEGATIVE (BLACK) clip from6.6
the battery charger to the NEGATIVE (NEG, N, -) ungrounded post of the
battery. Connect the POSITIVE (RED) clip to the vehicle chassis or engine
block away from the battery. Do not connect the clip to the carburetor, fuel
lines or sheet-metal body parts. Connect to a heavy gauge metal part of the
frame or engine block.
Connect the AC supply cord to the electrical outlet.6.7
When disconnecting the charger, turn all switches to off, disconnect the AC6.8
cord, remove the clip from the vehicle chassis and then remove the clip from
the battery terminal.

6
See CALCULATING CHARGE TIME for length of charge information.6.9
FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE7.
VEHICLE.
A spark near the battery may cause a
battery explosion. To reduce the risk
of a spark near the battery:
Check the polarity of the battery posts. The POSITIVE (POS, P, +) battery7.1
post usually has a larger diameter than the NEGATIVE (NEG, N, -) post.
Attach at least a 24-inch (61 cm) long 6-gauge (AWG) insulated battery cable7.2
to the NEGATIVE (NEG, N, -) battery post.
Connect the POSITIVE (RED) charger clip to the POSITIVE (POS, P, +) post7.3
of the battery.
Position yourself and the free end of the cable you previously attached to the7.4
NEGATIVE (NEG, N, -) battery post as far away from the battery as possible
– then connect the NEGATIVE (BLACK) charger clip to the free end of the
cable.
Donotfacethebatterywhenmakingthenalconnection.7.5
Connect the AC supply cord to the electrical outlet.7.6
When disconnecting the charger, always do so in the reverse order of the7.7
connectingprocedureandbreaktherstconnectionwhileasfarawayfrom
the battery as practical.
A marine (boat) battery must be removed and charged on shore. To charge it7.8
onboard requires equipment specially designed for marine use.
BATTERY CHARGING – AC CONNECTIONS8.
Riskofelectricshockorre.
This battery charger is for use on a nominal 120-volt circuit. The charger must8.1
be grounded to reduce the risk of electric shock. The plug must be plugged
into an outlet that is properly installed and grounded in accordance with all
localcodesandordinances.Theplugpinsmusttthereceptacle(outlet).Do
not use with an ungrounded system.

7
NeveralterACcordorplugprovided–ifitdoesnotttheoutlet,haveproper8.2
groundedoutletinstalledbyaqualiedelectrician.Improperconnection
can result in a risk of an electric shock or electrocution. NOTE: Pursuant to
Canadian Regulations, use of an adapter plug is not allowed in Canada. Use
of an adapter plug in the United States is not recommended.
Recommended minimum AWG size for extension cord:8.3
100 feet long or less - use an 18 gauge extension cord.•
Over 100 feet long - use a 16 gauge extension cord.•
FEATURES9.
Battery Clip Cable Assembly1.
Ring Terminal Cable Assembly2.
Voltage Selector Switch3.
Reverse Connection Protection4.
1
2
3
ASSEMBLY INSTRUCTIONS10.
No assembly required.

8
CONTROL PANEL11.
Voltage Selector Switch
This charger has a voltage selector switch on the front of it. Match the charging
voltage (6 or 12 volts) to the voltage of the battery being charged.
Circuit Breaker
This charger is equipped with an internal self-resetting circuit breaker. The
breaker protects the charger from temporary overloads. In the event of an
overload, the breaker will trip open and after a short cooling off period, will
reset automatically. This process is known as cycling and can be recognized
by an audible clicking sound. If the circuit breaker is cycling, see the
TROUBLESHOOTING section.
OPERATING INSTRUCTIONS12.
Charging
Ensure that all of the charger components are in place and in good1.
working condition, including the plastic boots on the battery clips.
Connect the battery following the connection instructions described in2.
Using the Quick-Disconnect Cable Connectors section.
Connect the AC power following the precautions listed in Section 8.3.
USING THE QUICK-CONNECT CABLE CONNECTORS
Connect either of the two output cable assemblies to the charger in seconds.
Makesuretoplacethechargeronadry,non-ammablesurfacelikemetalor
concrete.
NOTE: Never connect the clip and ring terminal connectors together for use in
other applications, such as external battery or other power source charging, or to
extend the output cable length, as reverse polarity and/or overcharge conditions
will occur.
BATTERY CLIPS: Connect the battery clip cable assembly to the charger. Follow
the safety instructions in sections 6 or 7 to connect the output clips to the battery.
RING TERMINALS: The ring connectors permanently attach to the battery
providing easy access to quickly charge your battery. This application is
appropriate for motorcycles, lawn tractors, ATV’s and snowmobiles. To
permanently attach it to a battery, loosen and remove each nut from the bolts at
the battery terminals. Connect the red positive ring connector ring to the positive
(POS, P, +) battery terminal. Connect the black negative ring connector ring to
the negative (NEG, N, -) battery terminal. Replace and tighten the nuts to secure

9
it. Connect the ring connector cable assembly to the charger.
Completion of Charge
Ahydrometerreadingofthespecicgravityoftheelectrolyteofabatteryingood
condition should be between 1.25 and 1.285. When the battery reaches 80 to
85%offullcharge,bubbleswillappearonthesurfaceoftheuid.Asthebattery
nears full charge, the bubbling will become more vigorous.
CALCULATING CHARGE TIME13.
Thischargerhasaratedoutputof1amperewithanexpectednishrateof0.3
amperes. These outputs will vary with the age and condition of the battery being
charged.
This is a manual battery charger. Charging must be monitored
to prevent overcharging of the battery. Overcharging a battery could cause
personal injury and/or property damage.
Use the following table to more accurately determine the time it will take to bring
abatterytofullcharge.First,identifywhereyourbatterytsintothechart.
Find your battery’s rating on the chart below, and note the charge time given for
each charger setting. The times given are for batteries with a 50% charge prior to
recharging. Add more time for severely discharged batteries.
BATTERY SIZE/RATING CHARGING TIME
SMALL
BATTERIES
Motorcycle,
garden
tractor, etc.
6 - 12 AH 3¾ - 7½ hrs
12 - 32 AH 7½ - 20 hrs
CARS/
TRUCKS
200 - 315 CCA 40 - 60 RC 22½ - 28¾ hrs
315 - 550 CCA 60 - 85 RC 28¾ - 36½ hrs
550 - 1000 CCA 80 - 190 RC 36½ - 69½ hrs

10
MARINE/DEEP CYCLE
80 RC 35 hrs
140 RC 53¾ hrs
160 RC 60 hrs
180 RC 66¼ hrs
MAINTENANCE INSTRUCTIONS14.
Before performing maintenance, unplug and disconnect the battery charger14.1
(see Sections 6, 7 and 8).
After use, unplug the charger and use a dry cloth to wipe all battery corrosion14.2
and other dirt or oil from the terminals, cords, and the charger case.
Ensure that all of the charger components are in place, securely attached and14.3
in good working condition, including the plastic boots on the battery clips.
Servicing does not require opening the unit, as there are no user-serviceable14.4
parts.
STORAGE INSTRUCTIONS15.

11
Store the charger unplugged, in an upright position. The cord will still conduct15.1
electricity until it is unplugged from the outlet.
Store inside, in a cool, dry place.15.2
Do not store the clips on the handle, clipped together, on or around metal, or15.3
clipped to cables.
TROUBLESHOOTING16.
PROBLEM POSSIBLE CAUSE REASON/SOLUTION
Charger will not turn
on when properly
connected.
AC outlet is dead.
Poor electrical
connection.
Severely discharged, but
otherwise good, battery.
Clips are not making a
good connection to the
battery.
Battery is defective.
Reverse connections at
battery.
Check for an open fuse or
circuit breaker supplying
the AC outlet.
Check the power cord and
extension cord for a loose
ttingplug.
The battery may not want
to accept a charge due to
a run-down state. Allow
the charging to continue
until the battery has had
a chance to recover
sufcientlyenoughtotake
a charge. If more than 20
minutes, stop charging
and have the battery
checked.
Check for poor connection
to battery and frame.
Make sure connection
points are clean. Rock
clips back and forth for a
better connection.
Have the battery checked.
Unplug the charger
and correct the lead
connections.
Charger makes a loud
buzz or hum. Transformer laminations vibrate (buzz).
Shorted Diode Assembly
orOutputRectier
Assembly (hum).
No problem, this is a
normal condition.
Have charger checked by
aqualiedtechnician.

12
PROBLEM POSSIBLE CAUSE REASON/SOLUTION
The charger is making an
audible clicking sound. Circuit breaker is cycling.
Battery is defective.
Shorted battery cables
or clips.
Severely discharged
battery, but otherwise it is
a good battery.
Reverse connections at
battery.
The settings may be
wrong. Check the charger
settings.
Have the battery checked.
Circuit breaker cycles
when current draw is too
high. Check for shorted
cables or clips and replace
if necessary.
The battery may not want
to accept a charge due to
a run-down state. Allow
charging to continue until
battery has a chance to
recoversufcientlytotake
a charge. If more than 20
minutes, stop charging
and have the battery
checked.
Shut the charger off
and correct the lead
connections.
The battery is connected
and the charger is on,
but is not charging.
Clips are not making a
good connection. Check for poor connection at battery and frame.
Make sure connecting
points are clean. Rock
clips back and forth for a
better connection.
BEFORE RETURNING FOR REPAIRS17.
When a charging problem arises, make certain that the battery is capable17.1
of accepting a normal charge. Use a good battery to double check all
connections, the AC outlet for a full 120-volts, the charger clips for correct
polarity and the quality of the connections from the cables to the clips and
from the clips to the battery system. The clips must be clean.
When a battery is very cold, partially charged or sulfated, it will not draw17.2
the full rated amperes from the charger. It is both dangerous and damaging
to a battery to force higher amperage into it than it can effectively use in
recharging.

13
When an UNKNOWN OPERATING PROBLEM arises, please read the17.3
complete manual and call the customer service number for information that
will usually eliminate the need for return.
If the above solutions do not eliminate the problem or for
information about troubleshooting or replacement parts,
call toll-free from anywhere in the U.S.A.
1-800-621-5485
7:00 am to 5:00 pm Central Time Monday thru Friday
SPECIFICATIONS18.
Input Voltage -------------------------------------------------------120V AC
Output Current Rating-------------------------------------------12V – 1A
6V – 1A
Maximum Charge Voltage----------------------------------12V – 14.8V
6V – 7.4V
Size-----------------------------------------------------2⅝”Hx6”Wx3”D
Weight-------------------------------------------------------------------2½ lbs
REPLACEMENT PARTS19.
Battery Clip Cable Assembly-----------------------------------------38-99-001235
Ring Terminal Cable Assembly--------------------------------------38-99-001233
LIMITED WARRANTY20.
SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER DRIVE,
MOUNT PROSPECT, IL 60056-2179, MAKES THIS LIMITED WARRANTY TO
THE ORIGINAL RETAIL PURCHASER OF THIS PRODUCT. THIS LIMITED
WARRANTY IS NOT TRANSFERABLE OR ASSIGNABLE.
Schumacher Electric Corporation (the “Manufacturer”) warrants this battery
charger for 2 years from the date of purchase at retail against defective material
or workmanship that may occur under normal use and care. If your unit is not
free from defective material or workmanship, Manufacturer’s obligation under this
warranty is solely to repair or replace your product with a new or reconditioned
unit at the option of the Manufacturer. It is the obligation of the purchaser to
forward the unit, along with mailing charges prepaid to the Manufacturer or its
authorized representatives in order for repair or replacement to occur.
Manufacturer does not provide any warranty for any accessories used with this
product that are not manufactured by Schumacher Electric Corporation and
approved for use with this product. This Limited Warranty is void if the product is
misused,subjectedtocarelesshandling,repaired,ormodiedbyanyoneother
than Manufacturer or if this unit is resold through an unauthorized retailer.

14
Manufacturer makes no other warranties, including, but not limited to, express,
implied or statutory warranties, including without limitation, any implied warranty
ofmerchantabilityorimpliedwarrantyoftnessforaparticularpurpose.Further,
Manufacturer shall not be liable for any incidental, special or consequential
damage claims incurred by purchasers, users or others associated with this
product,including,butnotlimitedto,lostprots,revenues,anticipatedsales,
business opportunities, goodwill, business interruption and any other injury or
damage. Any and all such warranties, other than the limited warranty included
herein, are hereby expressly disclaimed and excluded. Some states do not allow
the exclusion or limitation of incidental or consequential damages or length of
implied warranty, so the above limitations or exclusions may not apply to you.
Thiswarrantygivesyouspeciclegalrightsanditispossibleyoumayhaveother
rights which vary from this warranty.
THIS LIMITED WARRANTY IS THE ONLY EXPRESS LIMITED WARRANTY
AND THE MANUFACTURER NEITHER ASSUMES OR AUTHORIZES
ANYONE TO ASSUME OR MAKE ANY OTHER OBLIGATION TOWARDS THE
PRODUCT OTHER THAN THIS WARRANTY.
Schumacher Electric Corporation Customer Service
1-800-621-5485
Monday – Friday 7:00 a.m. to 5:00 p.m. CST
Schumacher and the Schumacher Logo are registered trademarks of
Schumacher Electric Corporation