SCORPION Exo-R410 User manual

Kido Sports USA, LLC.
ScorpionEXO Warranty/Tech Center
10425 Slusher Drive
Santa Fe Springs, CA 90670.USA
T: 1.888.212.0688
E: [email protected]

1
2
3
4
6
Advanced Composite Engineered Shell
5
5
7
Lock
Down
Retract
8
2
Performance
Features
Optically-clear shield with state-of-the art fog free
technology. Anti-Scratch hardened coating.
KwikWick II®anti-microbial fabric keeps you cool and dry
in warm weather, warm in cool weather Liner is easily
removable and washable. (See page 4-5 for details)
Easy, Secure, tool-less faceshield changes in seconds.
Pulls the shield back against the eyeport gasket during
closing to ensure a proper seal. (See page 7 for details)
SNELL M2010/DOT
Five intake ports across the front of helmet forces cool air in
while four exhaust vents maximize movement of hot air out.
EverClear®No Fog FaceShield
KwikWick II®Liner Fabric
Ellip-Tec™Ratchet System
Aero-Tuned Ventilation
2
KwikFit™cheekpads allow easy on and off of the most
common styles of eye glasses
KwikFit™
1
1
4
5
Shield securely locks in place. Or turn down for a light air
flow when riding at low speeds. (See page 3 for details)
Face Shield Lock / Vent System
3
6
Advanced multi-layer EPS provides efficient energy
displacement in key areas. EPS liner throughout entire chin
bar area.
Advanced Dual-Density EPS:
7
Introduction
Function
Fit
FaceShields
Ventilation Systems
Ventilation helps decrease the possibility of fogging
and condensation.
Ellip-Tec
Tabs located under the neck roll allow easy removal of the cheek
pads by emergency medical personnel thus allowing easier removal
of the helmet. (See page 7 for details and warning)
Emergency Release System
8
1
2
3
4
6
Advanced Composite Engineered Shell
5
5
7
Lock
Down
Retract
8
2
Performance
Features
Optically-clear shield with state-of-the art fog free
technology. Anti-Scratch hardened coating.
KwikWick II®anti-microbial fabric keeps you cool and dry
in warm weather, warm in cool weather Liner is easily
removable and washable. (See page 4-5 for details)
Easy, Secure, tool-less faceshield changes in seconds.
Pulls the shield back against the eyeport gasket during
closing to ensure a proper seal. (See page 7 for details)
SNELL M2010/DOT
Five intake ports across the front of helmet forces cool air in
while four exhaust vents maximize movement of hot air out.
EverClear®No Fog FaceShield
KwikWick II®Liner Fabric
Ellip-Tec™Ratchet System
Aero-Tuned Ventilation
2
KwikFit™cheekpads allow easy on and off of the most
common styles of eye glasses
KwikFit™
1
1
4
5
Shield securely locks in place. Or turn down for a light air
flow when riding at low speeds. (See page 3 for details)
Face Shield Lock / Vent System
3
6
Advanced multi-layer EPS provides efficient energy
displacement in key areas. EPS liner throughout entire chin
bar area.
Advanced Dual-Density EPS:
7
Introduction
Function
Fit
FaceShields
Ventilation Systems
Ventilation helps decrease the possibility of fogging
and condensation.
Ellip-Tec
Tabs located under the neck roll allow easy removal of the cheek
pads by emergency medical personnel thus allowing easier removal
of the helmet. (See page 7 for details and warning)
Emergency Release System
8

1
2
3
4
6
Advanced Composite Engineered Shell
5
5
7
Lock
Down
Retract
8
2
Performance
Features
Optically-clear shield with state-of-the art fog free
technology. Anti-Scratch hardened coating.
KwikWick II®anti-microbial fabric keeps you cool and dry
in warm weather, warm in cool weather Liner is easily
removable and washable. (See page 4-5 for details)
Easy, Secure, tool-less faceshield changes in seconds.
Pulls the shield back against the eyeport gasket during
closing to ensure a proper seal. (See page 7 for details)
SNELL M2010/DOT
Five intake ports across the front of helmet forces cool air in
while four exhaust vents maximize movement of hot air out.
EverClear®No Fog FaceShield
KwikWick II®Liner Fabric
Ellip-Tec™Ratchet System
Aero-Tuned Ventilation
2
KwikFit™cheekpads allow easy on and off of the most
common styles of eye glasses
KwikFit™
1
1
4
5
Shield securely locks in place. Or turn down for a light air
flow when riding at low speeds. (See page 3 for details)
Face Shield Lock / Vent System
3
6
Advanced multi-layer EPS provides efficient energy
displacement in key areas. EPS liner throughout entire chin
bar area.
Advanced Dual-Density EPS:
7
Introduction
Function
Fit
FaceShields
Ventilation Systems
Ventilation helps decrease the possibility of fogging
and condensation.
Ellip-Tec
Tabs located under the neck roll allow easy removal of the cheek
pads by emergency medical personnel thus allowing easier removal
of the helmet. (See page 7 for details and warning)
Emergency Release System
8

Face Shield Lock/Vent Lever
3
Note: First, Close Shield to the
lowest position to Lock/Unlock.
To lock the faceshield, turn Locking-lever counter
clockwise to the 2 o’clock position approximately.
Check face shield if it’s securely locked.
To unlock the faceshield, and provide air flow at
low speeds, turn Locking-lever clockwise to the 5
o’clock position. Test faceshield to check if it is
unlocked.
Note: When the lever is positioned at 3 o’clock, the shield
is closed, but it is also unlocked.
4
Cheek Pads Removal
DO NOT ATTEMPT TO ADJUST WHILE RIDING
PULL
Occassionally the cheek pads may require
removal for washing or replacement.
First step: Remove the Aero Skirt.
(refer to page 6).
Second step: Slide your thumb between the
cheek pad and chin bar, gently tug. Once
both cheek pads are removed you can also
remove the crown liner component.
(refer to page 5)
Third step: Gently pull cheek pad away from
inner chin bar to unsnap the three plastic
clips.
Repeat this process for both cheek pads.
Once both cheek pads are removed you can
also remove the crown liner component.
(refer to page 5)
Reverse this process for installation.
Face Shield Lock/Vent Lever
3
Note: First, Close Shield to the
lowest position to Lock/Unlock.
To lock the faceshield, turn Locking-lever counter
clockwise to the 2 o’clock position approximately.
Check face shield if it’s securely locked.
To unlock the faceshield, and provide air flow at
low speeds, turn Locking-lever clockwise to the 5
o’clock position. Test faceshield to check if it is
unlocked.
Note: When the lever is positioned at 3 o’clock, the shield
is closed, but it is also unlocked.
4
Cheek Pads Removal
DO NOT ATTEMPT TO ADJUST WHILE RIDING
PULL
Occassionally the cheek pads may require
removal for washing or replacement.
First step: Remove the Aero Skirt.
(refer to page 6).
Second step: Slide your thumb between the
cheek pad and chin bar, gently tug. Once
both cheek pads are removed you can also
remove the crown liner component.
(refer to page 5)
Third step: Gently pull cheek pad away from
inner chin bar to unsnap the three plastic
clips.
Repeat this process for both cheek pads.
Once both cheek pads are removed you can
also remove the crown liner component.
(refer to page 5)
Reverse this process for installation.

Face Shield Lock/Vent Lever
3
Note: First, Close Shield to the
lowest position to Lock/Unlock.
To lock the faceshield, turn Locking-lever counter
clockwise to the 2 o’clock position approximately.
Check face shield if it’s securely locked.
To unlock the faceshield, and provide air flow at
low speeds, turn Locking-lever clockwise to the 5
o’clock position. Test faceshield to check if it is
unlocked.
Note: When the lever is positioned at 3 o’clock, the shield
is closed, but it is also unlocked.
4
Cheek Pads Removal
DO NOT ATTEMPT TO ADJUST WHILE RIDING
PULL
Occassionally the cheek pads may require
removal for washing or replacement.
First step: Remove the Aero Skirt.
(refer to page 6).
Second step: Slide your thumb between the
cheek pad and chin bar, gently tug. Once
both cheek pads are removed you can also
remove the crown liner component.
(refer to page 5)
Third step: Gently pull cheek pad away from
inner chin bar to unsnap the three plastic
clips.
Repeat this process for both cheek pads.
Once both cheek pads are removed you can
also remove the crown liner component.
(refer to page 5)
Reverse this process for installation.

Crown Liner Removal
6
5
Aero Skirt Removal
Occassionally the crown liner may require
removal for washing, replacement or to
change sizes.
First step is to remove the Cheek Pads.
(refer to page 4).
At the back of the helmet pull the crown
liner away from the shell.
Pull the crown liner out of the helmet while
gently detaching it from the forehead
channel.
Reverse this process for installation.
The pliable Aero Skirt was designed to
reduce wind from entering behind the
face shield area, specifically to keep
your face warmer in cold weather.
You do however have the option to
remove the Aero Skirt for cleaning or
for warmer riding conditions.
TO REMOVE
Simply tug on the Aero Skirt and it
slides out of the rubber trim channel.
Reverse this process to re-install.
LLUP
Crown Liner Removal
6
5
Aero Skirt Removal
Occassionally the crown liner may require
removal for washing, replacement or to
change sizes.
First step is to remove the Cheek Pads.
(refer to page 4).
At the back of the helmet pull the crown
liner away from the shell.
Pull the crown liner out of the helmet while
gently detaching it from the forehead
channel.
Reverse this process for installation.
The pliable Aero Skirt was designed to
reduce wind from entering behind the
face shield area, specifically to keep
your face warmer in cold weather.
You do however have the option to
remove the Aero Skirt for cleaning or
for warmer riding conditions.
TO REMOVE
Simply tug on the Aero Skirt and it
slides out of the rubber trim channel.
Reverse this process to re-install.
LLUP

Crown Liner Removal
6
5
Aero Skirt Removal
Occassionally the crown liner may require
removal for washing, replacement or to
change sizes.
First step is to remove the Cheek Pads.
(refer to page 4).
At the back of the helmet pull the crown
liner away from the shell.
Pull the crown liner out of the helmet while
gently detaching it from the forehead
channel.
Reverse this process for installation.
The pliable Aero Skirt was designed to
reduce wind from entering behind the
face shield area, specifically to keep
your face warmer in cold weather.
You do however have the option to
remove the Aero Skirt for cleaning or
for warmer riding conditions.
TO REMOVE
Simply tug on the Aero Skirt and it
slides out of the rubber trim channel.
Reverse this process to re-install.
LLUP

7
Cleaning Your Helmet System
FaceShield Replacement Securing and Wearing your Helmet
RATCHETING SYSTEM
To remove your faceshield, place the helmet in front of you with the eye
port facing away. Ratchet the faceshield up to the fully open position.
Using both hands, push up the Y shape release latchet upward and the
shield is able to release out of locking mechanism. Than, with both of your
thumbs pushing squarely on the center of the Ellip-Tec™, gently pull or
“peel” the faceshield away from the helmet.
IMPORT NOTE:
Be sure to latch up the
“Y” release latchet
while removing the
faceshield!
Continued on pg. 9 >>
FIRMLY AND SECURELY FASTEN YOUR CHINSTRAP.
Check your chinstrap for tightness occasionally as vibration or wind may
loosen it.
Do not simply pull your helmet down onto your head like a hat. Your Scorpion-
Exo™ helmet should be worn as follows: Using both hands grab the helmet’s
bottom rim while holding the chin straps with your thumbs. Then “roll” the
helmet onto your head starting at the forehead. Continue rolling the helmet on
towards the back of the head until it comes to rest with your head fully in
contact with the inner lining and cheek pads.
HOW TO USE CHINSTRAP
8
Emergency Release System
Locate the emergency labeling on the
neck roll. Simply reach under the
neck roll and grab the release strap,
pull at a 45 degree angle towards
front of helmet. The cheek liner will
easily release from the helmet. This
system should only be used by
trained medical personnel.
Emergency Safety Release System
DO NOT ATTEMPT TO RELEASE WHILE RIDING
IN CASE OF ACCIDENT DO NOT ATTEMPT REMOVAL ON YOUR OWN
SNAP
PUSH
SNAP Slot
PULL
Cheek Pad
SNAP
PUSH
SNAP Hole
PRECAUTION
1. SNAP may come off from the Cheek Pad
during Cheek Pad removal.
2. Locate the separated SNAP and reassemble
on to the Cheek Pad by pushing the SNAP into
the SNAP Slot on the Cheek Pad.
3. Align SNAP on the Cheek Pad to the SNAP
Hole and push the snap in until sound is heard.
12
3
!

7
Cleaning Your Helmet System
FaceShield Replacement Securing and Wearing your Helmet
RATCHETING SYSTEM
To remove your faceshield, place the helmet in front of you with the eye
port facing away. Ratchet the faceshield up to the fully open position.
Using both hands, push up the Y shape release latchet upward and the
shield is able to release out of locking mechanism. Than, with both of your
thumbs pushing squarely on the center of the Ellip-Tec™, gently pull or
“peel” the faceshield away from the helmet.
IMPORT NOTE:
Be sure to latch up the
“Y” release latchet
while removing the
faceshield!
Continued on pg. 9 >>
FIRMLY AND SECURELY FASTEN YOUR CHINSTRAP.
Check your chinstrap for tightness occasionally as vibration or wind may
loosen it.
Do not simply pull your helmet down onto your head like a hat. Your Scorpion-
Exo™ helmet should be worn as follows: Using both hands grab the helmet’s
bottom rim while holding the chin straps with your thumbs. Then “roll” the
helmet onto your head starting at the forehead. Continue rolling the helmet on
towards the back of the head until it comes to rest with your head fully in
contact with the inner lining and cheek pads.
HOW TO USE CHINSTRAP
8
Emergency Release System
Locate the emergency labeling on the
neck roll. Simply reach under the
neck roll and grab the release strap,
pull at a 45 degree angle towards
front of helmet. The cheek liner will
easily release from the helmet. This
system should only be used by
trained medical personnel.
Emergency Safety Release System
DO NOT ATTEMPT TO RELEASE WHILE RIDING
IN CASE OF ACCIDENT DO NOT ATTEMPT REMOVAL ON YOUR OWN
SNAP
PUSH
SNAP Slot
PULL
Cheek Pad
SNAP
PUSH
SNAP Hole
PRECAUTION
1. SNAP may come off from the Cheek Pad
during Cheek Pad removal.
2. Locate the separated SNAP and reassemble
on to the Cheek Pad by pushing the SNAP into
the SNAP Slot on the Cheek Pad.
3. Align SNAP on the Cheek Pad to the SNAP
Hole and push the snap in until sound is heard.
12
3
!

Like us on Facebook for a chance to win Scorpion products:
https://www.facebook.com/ScorpionExoUSA
Follow us on Twitter to be the first to know about new products :
https://twitter.com/ScorpionExo
Subscribe to our YouTube page for fresh videos on our latest products:
http://www.youtube.com/user/ScorpionNation
Download our FREE iPhone/iPad App. available on the App Store:
http://itunes.apple.com/us/app/scorpionexo/id429393136?mt=8
Follow us on Instagram for a visual look into the Scorpion nest:
Search user @Scorpionexo or #scorpionexo
FOLLOW US ON OUR SOCIAL NETWORKS
Scan to visit our website:
10
9
Warning
DO NOT
Warranty
For your safety, it is important that you completely read the
owner’s manual and all warning labels.
DO NOT ride without snugly fastening your chinstrap.
DO NOT clean your helmet with petroleum products, solvents,
benzene, thinner or cleaning agents.
DO NOT paint over your helmet’s finish without totally protecting
and isolating the shock-absorbing liner and plastic parts.
Your warranty will otherwise be invalidated.
DO NOT drop your helmet from any height onto a hard surface.
This could cause damage to your helmet’s finished and/or
decrease its ability to protect you.
DO NOT place your helmet on your motorcycle’s rearview mirror:
The sharp pressure from the mirror’s edge will compress and
damage the helmet’s shock-absorbing liner.
DO NOT place your helmet on the motorcycle’s seat or fuel tank.
It can easily roll off and hit the ground causing damage to the
helmet. It is best to place your helmet on the ground so it cannot
fall in any direction.
For on-line registration of your new ScorpionEXO helmet,
please log onto www.scorpionusa.com/support/product-
registration.html . Should you have a warranty claim, please
call 888-212-0688 or email [email protected]
during business hours (PST). Details of your ScorpionEXO
warranty can be found online:
www.scorpionusa.com/support/warranty-and-returns.html
DO NOT ride with a scratched faceshield. This can impair your
vision, especially at night.
DO NOT modify any part of your helmet, e.g., drilling the shell or
cutting and pressing the shock absorbing liner. Installation of
sound systems, speakers and microphones reduces your
helmet’s ability to protect you and is not recommended.
DO NOT use the helmet again if it has either been dropped or
involved in an accident. Replace it even if the damage is not
visible to the naked eye.
DO NOT wear a dark or tinted faceshield (including the
retractable SpeedViewTM Sunvisor) in dark or poor visibility
riding conditions.
DO NOT place your headliners and cheek pads in the dryer after
washing. Allow them to air dry.
DO NOT attempt to remove, change or replace your faceshield
while riding your motorcycle or ATV.
DO NOT use paint which requires heat curing.
Continued from pg. 9 >>

Like us on Facebook for a chance to win Scorpion products:
https://www.facebook.com/ScorpionExoUSA
Follow us on Twitter to be the first to know about new products :
https://twitter.com/ScorpionExo
Subscribe to our YouTube page for fresh videos on our latest products:
http://www.youtube.com/user/ScorpionNation
Download our FREE iPhone/iPad App. available on the App Store:
http://itunes.apple.com/us/app/scorpionexo/id429393136?mt=8
Follow us on Instagram for a visual look into the Scorpion nest:
Search user @Scorpionexo or #scorpionexo
FOLLOW US ON OUR SOCIAL NETWORKS
Scan to visit our website:
10
9
Warning
DO NOT
Warranty
For your safety, it is important that you completely read the
owner’s manual and all warning labels.
DO NOT ride without snugly fastening your chinstrap.
DO NOT clean your helmet with petroleum products, solvents,
benzene, thinner or cleaning agents.
DO NOT paint over your helmet’s finish without totally protecting
and isolating the shock-absorbing liner and plastic parts.
Your warranty will otherwise be invalidated.
DO NOT drop your helmet from any height onto a hard surface.
This could cause damage to your helmet’s finished and/or
decrease its ability to protect you.
DO NOT place your helmet on your motorcycle’s rearview mirror:
The sharp pressure from the mirror’s edge will compress and
damage the helmet’s shock-absorbing liner.
DO NOT place your helmet on the motorcycle’s seat or fuel tank.
It can easily roll off and hit the ground causing damage to the
helmet. It is best to place your helmet on the ground so it cannot
fall in any direction.
For on-line registration of your new ScorpionEXO helmet,
please log onto www.scorpionusa.com/support/product-
registration.html . Should you have a warranty claim, please
call 888-212-0688 or email [email protected]
during business hours (PST). Details of your ScorpionEXO
warranty can be found online:
www.scorpionusa.com/support/warranty-and-returns.html
DO NOT ride with a scratched faceshield. This can impair your
vision, especially at night.
DO NOT modify any part of your helmet, e.g., drilling the shell or
cutting and pressing the shock absorbing liner. Installation of
sound systems, speakers and microphones reduces your
helmet’s ability to protect you and is not recommended.
DO NOT use the helmet again if it has either been dropped or
involved in an accident. Replace it even if the damage is not
visible to the naked eye.
DO NOT wear a dark or tinted faceshield (including the
retractable SpeedViewTM Sunvisor) in dark or poor visibility
riding conditions.
DO NOT place your headliners and cheek pads in the dryer after
washing. Allow them to air dry.
DO NOT attempt to remove, change or replace your faceshield
while riding your motorcycle or ATV.
DO NOT use paint which requires heat curing.
Continued from pg. 9 >>

Kido Sports USA, LLC.
ScorpionEXO Warranty/Tech Center
10425 Slusher Drive
Santa Fe Springs, CA 90670.USA
T: 1.888.212.0688
E: [email protected]