Scosche IDKCR01 User manual

©2016 SCOSCHE INDUSTRIES, INC
IDKCR01 / IDKFD01
IDKFD02 / IDKGM01
IDKTA01
IPAD DASH KIT
INSTALLATION INSTRUCTIONS
Scosche iPad dash kits are designed and engineered to safely mount onto the vehicle’s OEM radio
panel, while retaining full access to the Factory stereo when removed. All iPad kits are designed with
iPad Dash Kit w/ 3M™ Adhesive Backing
Alcohol Prep. Pad
(3000614) IDK_CRO1/FD01/FD02/GM01/TA01) 10/16
This instruction booklet is based on carefully documented data and research of the automobile and information
pertaining to the installation of this kit. Scosche Industries, Inc. cannot be held responsible for discrepancies /
inconsistencies that may occur due to the automobile manufacturing changes or options, or damage that may occur
in the automobile during the installation of components while using this booklet.
DISCLAIMER
Check all state, federal and local laws before installing the iPad dash kit.
It is the responsibility of the user to determine, and obey, all applicable
laws regarding use of electronic devices while operating a vehicle.
INTRODUCTION
VEHICLE APPLICATION GUIDE
Included
IDKFD02
IDKFD01
IDKCR01
IDKTA01
IDKGM01
IDKCR01 2013-15 DODGE RAM TRUCKS (w/ Uconnect 8.4”)
IDKFD01 2015-UP FORD F-150 (w/ SYNC3 8” Touch Screen)
IDKFD02 2013-14 FORD F-150
IDKGM01 2014-UP CHEVY SILVERADO / GMC SIERRA (w/ 7” MyLink Display)
IDKTA01 2012-15 TOYOTA TACOMA
2015-UP FORD F-150 & 2017 SUPER DUTY

2
INSTALLATION GUIDE
INSTALLATION GUIDE
Kit Preparation & Installation
Mounting/Removing
IMPORTANT! Please read and follow the directions below before and during the installation process. Check all
state, federal and local laws before installing the iPad dash kit. It is the responsibility of the user to determine, and
obey, all applicable laws regarding use of electronic devices while operating a vehicle.
FIGURE 2
FIGURE 1
FIGURE 3 FIGURE 4
Peel the adhesive backing from the 3M™ strips on the back
of the kit. FIG 2
Carefully align the iPad kit over the factory stereo location
and press rmly for a full 60 seconds (adhesive fully cures
after 24hrs).
INSTALLATION STEPS
Use the supplied alcohol prep pad to clean the surface area
around the Factory radio panel where the iPad kit will make
contact with the surface. (Place the kit over the factory
stereo to verify proper tament if needed. iPad kits are
designed to exactly match the shape and contour of the
Factory stereo panel) FIG 1
1.
2.
3.
MOUNTING / REMOVING THE TABLET
1. Carefully slide the iPad, with side controls UP, in (or out) of the channel as shown in FIG 3.
2. Sample illustration of end result FIG 4.

©2016 SCOSCHE INDUSTRIES, INC
IDKCR01 / IDKFD01
IDKFD02 / IDKGM01
IDKTA01
IPAD DASH KIT
INSTALLATION INSTRUCTIONS
Scosche iPad dash kits are designed and engineered to safely mount onto the vehicle’s OEM radio
panel, while retaining full access to the Factory stereo when removed. All iPad kits are designed with
a low prole and retain access to tablet controls and charging port.
iPad Dash Kit w/ 3M™ Adhesive Backing
Alcohol Prep. Pad
(3000614) IDK_CRO1/FD01/FD02/GM01/TA01) 10/16
This instruction booklet is based on carefully documented data and research of the automobile and information
pertaining to the installation of this kit. Scosche Industries, Inc. cannot be held responsible for discrepancies /
inconsistencies that may occur due to the automobile manufacturing changes or options, or damage that may occur
in the automobile during the installation of components while using this booklet.
DISCLAIMER
Check all state, federal and local laws before installing the iPad dash kit.
It is the responsibility of the user to determine, and obey, all applicable
laws regarding use of electronic devices while operating a vehicle.
INTRODUCTION
VEHICLE APPLICATION GUIDE
Included
IDKFD02
IDKFD01
IDKCR01
IDKTA01
IDKGM01
IDKCR01 2013-15 DODGE RAM TRUCKS (w/ Uconnect 8.4”)
IDKFD01 2015-UP FORD F-150 (w/ SYNC3 8” Touch Screen)
IDKFD02 2013-14 FORD F-150
IDKGM01 2014-UP CHEVY SILVERADO / GMC SIERRA (w/ 7” MyLink Display)
IDKTA01 2012-15 TOYOTA TACOMA

2
INSTALLATION GUIDE
INSTALLATION GUIDE
Kit Preparation & Installation
Mounting/Removing
IMPORTANT! Please read and follow the directions below before and during the installation process. Check all
state, federal and local laws before installing the iPad dash kit. It is the responsibility of the user to determine, and
obey, all applicable laws regarding use of electronic devices while operating a vehicle.
FIGURE 2
FIGURE 1
FIGURE 3 FIGURE 4
Peel the adhesive backing from the 3M™ strips on the back
of the kit. FIG 2
Carefully align the iPad kit over the factory stereo location
and press rmly for a full 60 seconds (adhesive fully cures
after 24hrs).
INSTALLATION STEPS
Use the supplied alcohol prep pad to clean the surface area
around the Factory radio panel where the iPad kit will make
contact with the surface. (Place the kit over the factory
stereo to verify proper tments if needed. iPad kits are
designed to exactly match the shape and contour of the
Factory stereo panel) FIG 1
1.
2.
3.
MOUNTING / REMOVING THE TABLET
1. Carefully slide the iPad, with side controls UP, in (or out) of the channel as shown in FIG 3.
2. Sample illustration of end result FIG 4.