Screen Innovations Solo 2 User manual

Solo / Pro 2
Installation Instructions
110v AC Motors

Thank you for purchasing an SI product. If you have
any questions or need any assistance with your
Solo/Pro 2, we would love to help you.
Technical Support: 512.832.6939
Hours of Support: 7:30am - 5pm CST
screeninnovations.com
[email protected]
Solo Pro 2Solo 2
Please use these QR Codes to access the updated
installation instructions and video tutorials.

CONTENTS
Initial Consideration ..................................................... 1
Parts in the Box - AC(110v) RTS ............................... 2
Parts in the Box - AC(110v) 485 ............................... 3
Spacer Blocks and Leveling Shims ......................... 4
Pre-wire - AC(110v) 485 ............................................ 5
Installation .................................................................... 6 - 14
Flatten the material at the weight bar...................... 15
Pairing another RF Remote ....................................... 16
Motor Commissioning Guide Ref............................. 17
Control Guide Ref.......................................................... 18 - 19
Mounting Accessories ............................................... 20
Motor Accessories AC(110v) RTS ................................ 21
Motor Accessories AC(110v) 485................................. 22
Storage and Transport .................................................... 23 - 24
Care and Maintenance .................................................... 25
Troubleshooting ..................................................................26 - 29
Warranty .............................................................................. 30

1
INITIAL CONSIDERATIONS
Thank you for your purchase of Solo/Pro 2. The screen
is mountable outdoors, but is not waterproof. It has not
been designed to be run or left in the rain or condensing
humidity. Also avoid water spray, splash and extreme
heat or cold. Protect your Solo/Pro 2. and you can expect
years of quality use.
For a quick install it is recommended you run appropriate
wire to the installation location before installing the
screen. See the Pre-Wire sections for details.
Follow all local electrical codes when running and
terminating AC(110v) wires. It is the responsibility of the
installer to make sure AC(110v) screens are installed to
electrical safety codes.
The Short Throw material is not 100% opaque.
Light sources behind the screen may be visible in
the viewing surface.
Initial Considerations

2
AC(110v) RTS
RF Remote
AC(110v) RTS - Parts in the Box
(2) Ceiling/Wall
Locking brackets
(6) Leveling Shims
PWR Solo/Pro 2 screen
Parts in the box
(6) Wood
fasteners

3
(6) Leveling Shims
AC(110v) 485
Parts in the box
AC(110v) 485 - Parts in the Box
(6) Wood
fasteners
Additional
accessories
required for 485
control (pg. 34)
Solo/Pro 2 screen
485PWR
(2) Ceiling/Wall
Locking brackets
RJ45 coupler
and bracket
USB
Programming Kit

4
Spacer Blocks & Leveling Shims
SPACER BLOCKS & LEVELING
SHIMS
Spacer Blocks are used to
clear an obstruction on the
wall. Connect spacer block
to each wall bracket before
installation.
Leveling Shims are used if
the ceiling or other
mounting surface is out
of level or plumb. Connect
to ceiling brackets before
installation.

5
Pre-Wire - AC(110v) RTS
PRE-WIRE - AC(110v) 485
1. Run Cat5e cable to the left side of screen cassette
installation location (refer to pg. 9).
2. Terminate the wires with the provided pinout as
shown below or use the incl. coupler to extend the
cable upto 200'.
RS485 (+) - White
RS485 (-) - Orange
-
Power 7v DC - Red
-
-
-
Ground - Brown
Pin 1
Pin 8
Service Loop
Note: Red Service loop, can be cut to disable the DC
output from an AC 485 motor.

6
Proper mounting preparation will ensure a great
installation. Mounting brackets must be level to each
other, as well as plumb. They must be screwed into
structural members of some kind, such as ceiling
joists or wall studs. You may use the wood screws
provided, or other anchors (not provided) capable of
carrying the load, that is suitable to the substrate.
DO NOT MOUNT TO HOLLOW SHEET ROCK.
1. The drop is adjustable in the field between 0'' and
the MAX DROP (12'', 24'', or 36'', 2'' for short throw)
ordered for your screen. Use the drawing (refer to
pg. 7) to pick a bracket height that will allow you to
extend your screen to achieve the desired vertical
position of your viewing area.
INSTALLATION
Solo/Pro 2 - Installation