Screen Innovations Solo 3 User manual

INSTALLERS: Please leave this manual with the owner.
Solo 3
Indoor
375 External
Installation Instructions
®
4000XX Ι v. 1.0 Ι 13 April 2022

Screen Innovations warrants its products, to the original purchaser only, to be free from defects in materials and
workmanship for a period of one (1) year from the date of purchase by the original purchaser provided they are
properly operated according to Screen Innovations' instructions and are not damaged due to improper handling
or treatment after shipment from the factory.
This warranty does not apply to equipment showing evidence of misuse, abuse, or accidental damage, or which
has been tampered with or repaired by a person other than authorized Screen Innovations personnel.
Screen Innovations’ sole obligation under this warranty shall be to repair or to replace (at Screen Innovations’
option) the defective part of the merchandise. Returns for service should be made to your Screen Innovations'
dealer. If it is necessary for the dealer to return the screen or part to Screen Innovations, transportation
expenses to and from Screen Innovations are payable by the purchaser and Screen Innovations is not
responsible for damage in shipment. To protect yourself against damage or loss in transit, insure the product
and prepay all transportation expenses.
This warranty is in lieu of all other warranties, express or implied, including warranties as to tness for use and
merchant ability. Any implied warranties of tness for use, or merchantability, that may be mandated by statute
or rule of law are limited to the one (1) year warranty period. This warranty gives you specic legal rights, and
you may also have other rights, which vary from state-to-state. No liability is assumed for expenses or damages
resulting from interruption in operation of equipment, or for incidental, direct, or consequential damages of any
nature.
In the event that there is a defect in materials or workmanship of a Screen Innovations product, you may contact
our Sales Partners at 9715-B Burnet Road Suite 400, Austin, TX 78758, [phone].
Important: this warranty shall not be valid and screen innovations shall not be bound by this warranty if the
product is not operated in accordance with screen innovations' written instructions.
Keep your sales receipt to prove the date of purchase and your original ownership.
Limited 1 year warranty
on Screen Innovations products
Technical Support: 512.832.6939 screeninnovations.com
Hours of Support: 7:30am - 5pm CST [email protected]
Scan this QR Code
to access the
updated installation
instructions and
related documents.

TABLE OF CONTENTS
Parts in the Box .............................................................................4
Spacer Blocks and Leveling Shims (Optional) ................................................5
Installation – Solo 3 375 External – Indoor ..................................................6 – 12
Power Options ............................................................................8 – 11
AC, Low Voltage (DC), and Control – Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Setting Up Wired Screen Using Moab ...........................................9–10
Wire Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
References ................................................................................. 13
Servicing Solo 3 375 External – Indoor......................................................14–22
Inspecting the Roll ..............................................................14–15
Tube Removal...................................................................16–17
Tube Installation ................................................................18–21
Wireless Sleep Mode .............................................................22

4
Spacer Blocks
(Optional – 4 per screen)
Moab Control Board
Longer Screws Included
Parts in the Box – Solo 3 375 External – Indoor
Leveling Shims
(4 per screen)
Screen Wall Brackets
Screws Included
(3 per Bracket)
IR Remote
Din Rail
Terminal Blocks and Bracket
(low voltage and/or 485)
PARTS IN THE BOX
375 Box
Installation Remotes
(1 per RTS screen)
Included remote’s form factor may
vary, however functionality and
performance is consistent.”
Included in the box with hardwired
control screens only

5
Spacer Blocks – Used to clear an obstruction in the screen or screen material path.
Before installing, connect spacer blocks to screen brackets.
NOTE: Do not use more than four (4) spacer blocks per bracket.
Leveling Shims – Used to level screen placement.
Before installing, connect to screen brackets.
NOTE: Do not use more than two (2) leveling shims per bracket.
SPACER BLOCKS AND LEVELING SHIMS (OPTIONAL)
Spacer Blocks and Leveling Shims

6
2–4” 2–4”
2. The recommended position for the box bracket is 2–4” from the end caps.
NOTE: Installing the wall brackets as close to the end of the cassette as possible ensures better
stability of the screen.
1. Terminate pre-wire with the supplied terminal block.
Data For 485 Only
Header
+ 24 VDC
- 24 VDC
Data +
Data -
Data ground
V+
V-
+
-
G
Jamb
INSTALLATION – SOLO 3 375 EXTERNAL – INDOOR
Installation – Solo 3 375 External – Indoor

7
3. To install the screen, start with the wall bracket lever pointed down in the unlocked position.
4. Ensure the terminal blocks are plugged in and installed in the brackets.
Proper position for installing Box
INSTALLATION – SOLO 3 375 EXTERNAL – INDOOR
Installation – Solo 3 375 External – Indoor
Data Cable
Power
Cable
NOTE: Refer to the next page to see the
wiring as per your power.

8
AC, LOW VOLTAGE (DC), AND CONTROL – WIRING
AC Wiring (AC Motor – Wireless control)
DC Wiring (AC Motor – Wired control)
DC Wiring (DC Motor – Wired control)
AC, LV (DC) Wiring
Marking
V+
V-
+
-
G
Description
Positive 24VDC
Negative 24VDC
485 Data Positive
485 Data Negative
485 Data Ground
24v DC Power Supply
RS485 Data+
RS485 Data-
RS485 Ground
Pigtail
Pigtail
Load (Black/Brown)
Neutral (White/Blue)
Ground (Green/Yellow)
*These colors on left are for USA,
international are on the right
Load (Black/Brown)
Neutral (White/Blue)
Ground (Green/Yellow)
RS485 (+) - White
RS485 (-) - Orange
-
Power 7v DC - Red
-
-
-
Ground - Brown
Pin 1
Pin 8
Service Loop
NOTE: Red Service loop, can be cut to disable the DC
output from an AC 485 motor.

9
Setting up Wired Screen Using Moab
DC Wire Diagram Illustrating Inital Setup
5. If the screen is wired with wired communication or 485 control, it will include a motor control board,
Moab. This control board allows for setting limits and/or controling the screen. Typically, this board is
located in the head end/equipment location. See the wiring chart on page 11 to determine maximum
wire length.
6. Upper and lower limits are already factory-set. Once all connections are made including the power
supply, you may now adjust the lower limits using the Moab control board.
SETTING UP WIRED SCREEN USING MOAB
Scan the QR code for complete details on how to install and program using
Moab.
485 MOTORS
485 MOTORS
ONLY
ONLY
485
485
DEVICES ONLY
DEVICES ONLY
3
3
8
8
8
8
UP
UP
6
6
8
8
USER
USER
ACT
ACT
MODES
MODES
1 2 3 4
1 2 3 4
485 BUS
485 BUS
8
8
6
6
5
5
1
1
&
&
IR REC
IR REC
ACTIVE
ACTIVE
L12
L12
L11
L11
L9
L9
L15
L15
L14
L14
L13
L13
L1
L1
L3
L3
L2
L2
L4
L4
L7
L7
L8
L8
302325
302325
202311 (EXT)
202311 (EXT)
202312 (INT)
202312 (INT)
VIEW
VIEW
VIEW
VIEW
485
485
LIMIT
LIMIT
LOWER
LOWER
LIMIT
LIMIT
MOTOR ROTATION
MOTOR ROTATION
STANDARD REVERSE
STANDARD REVERSE
9VDC
9VDC
485
485
DC MOTOR
DC MOTOR
485 PAIRING
485 PAIRING
STOP
STOP
UPPER
UPPER
IR REC
IR REC
IR
IR
LED
LED
BOARD
BOARD
SETTINGS
SETTINGS
6
6
3
3
(T)
(T)
-
-
STOP
STOP
485 DEVICE &
485 DEVICE &
DRY CONTACT PORT
DRY CONTACT PORT
3.5mm(1/8 in) mono (TS)
3.5mm(1/8 in) mono (TS)
(S)
(S)
+
+
RJ45 RJ9
RJ45 RJ9
12-28VDC
12-28VDC
DC POWER &
DC POWER &
485 DATA PORT
485 DATA PORT
DOWN
DOWN
AC MOTOR
AC MOTOR
G D- D+ V- V+
G D- D+ V- V+
3
3
6
6
2
2
4
4
5
5
7
7
8
8
1
1
V- V+
V- V+
12-28VDC
12-28VDC
D+
D+
D-
D-
G
G
12v TRIGGER PORT
12v TRIGGER PORT
PROG
PROG
BUTTONS
BUTTONS
DOWN
D O W N
485 NETWORK
485 NETWORK
MV
MV
STOP
STOP
ON
ON
LED1
LED1
S4
S4
S3
S3
S2
S2
LED15
LED15
LED14
LED14
LED13
LED13
LED12
LED12
LED11
LED11
LED9
LED9
LED8
LED8
LED7
LED7
LED4
LED4
LED3
LED3
LED2
LED2
IC3
IC3

10
7. Once all adjustments are made and nalized, the Moab may now be placed in a convenient location for
the install. Third party control such as Dry Contact closures, 12v Triggers, Serial Connections,
and Infrared may now be integrated with Moab.
SETTING UP WIRED SCREEN USING MOAB
Scan the QR code for complete pinout and third party integration details using
Moab.
485 MOTORS
485 MOTORS
ONLY
ONLY
485
485
DEVICES ONLY
DEVICES ONLY
3
3
8
8
8
8
UP
UP
6
6
8
8
USER
USER
ACT
ACT
MODES
MODES
1 2 3 4
1 2 3 4
485 BUS
485 BUS
8
8
6
6
5
5
1
1
&
&
IR REC
IR REC
ACTIVE
ACTIVE
L12
L12
L11
L11
L9
L9
L15
L15
L14
L14
L13
L13
L1
L1
L3
L3
L2
L2
L4
L4
L7
L7
L8
L8
302325
302325
202311 (EXT)
202311 (EXT)
202312 (INT)
202312 (INT)
VIEW
VIEW
VIEW
VIEW
485
485
LIMIT
LIMIT
LOWER
LOWER
LIMIT
LIMIT
MOTOR ROTATION
MOTOR ROTATION
STANDARD REVERSE
STANDARD REVERSE
9VDC
9VDC
485
485
DC MOTOR
DC MOTOR
485 PAIRING
485 PAIRING
STOP
STOP
UPPER
UPPER
IR REC
IR REC
IR
IR
LED
LED
BOARD
BOARD
SETTINGS
SETTINGS
6
6
3
3
(T)
(T)
-
-
STOP
STOP
485 DEVICE &
485 DEVICE &
DRY CONTACT PORT
DRY CONTACT PORT
3.5mm(1/8 in) mono (TS)
3.5mm(1/8 in) mono (TS)
(S)
(S)
+
+
RJ45 RJ9
RJ45 RJ9
12-28VDC
12-28VDC
DC POWER &
DC POWER &
485 DATA PORT
485 DATA PORT
DOWN
DOWN
AC MOTOR
AC MOTOR
G D- D+ V- V+
G D- D+ V- V+
3
3
6
6
2
2
4
4
5
5
7
7
8
8
1
1
V- V+
V- V+
12-28VDC
12-28VDC
D+
D+
D-
D-
G
G
12v TRIGGER PORT
12v TRIGGER PORT
PROG
PROG
BUTTONS
BUTTONS
DOWN
D O W N
485 NETWORK
485 NETWORK
MV
MV
STOP
STOP
ON
ON
LED1
LED1
S4
S4
S3
S3
S2
S2
LED15
LED15
LED14
LED14
LED13
LED13
LED12
LED12
LED11
LED11
LED9
LED9
LED8
LED8
LED7
LED7
LED4
LED4
LED3
LED3
LED2
LED2
IC3
IC3
Setting up Wired Screen Using Moab