Sea-doo 295100679 User manual

3/9/2017 einstructiondetails
http://instructions.brp.com/content/instructionsheet/en_CA/einstructiondetails.html#articleNo=kA0a0000000l0rxCAA&lang=en_CA&title=SEADOO%20KIT…
1/16
SEADOOKITDepthFinder
Partnumber(SKU):295100679
Product: SeaDoo_watercraft
Projectno: 487802049
InstructionSheetP/N: 487802049
Revisionno: 
Revisiondate: 
Itemcovered: DepthFinder(KitP/N:295100679)

PRIORTOINSTALLATION,PLEASEVERIFYIFAREVISEDVERSIONOFTHISINSTRUCTION
SHEETISAVAILABLEONKNOWLEDGECENTER.
Thefollowingsymbolsmaybeusedinthisdocument:
WARNING
Indicatesahazardoussituationwhich,ifnotavoided,couldresultindeathorseriousinjury.
CAUTION:Indicatesahazardsituationwhich,ifnotavoided,couldresultinminoror
moderateinjury.
NOTICE Indicatesaninstructionwhich,ifnotfollowed,couldseverelydamagevehicle
componentsorotherproperty.
WARNING
Forsafetyreasons,thiskitmustbeinstalledbyanauthorizedBRPdealer.
Thiskitisdesignedforspecificapplicablemodelsonly(authorizedBRPdealerswillconfirm
model(s)).Itisnotrecommendedforunitsotherthantheone(those)forwhichitwassold.
ThisinstructionsheetMUSTbegiventothepurchaser.
Shouldremovalofalockingdevice(e.g.locktabs,selflockingfasteners,etc.)berequired
whenundergoingdisassembly/assembly,alwaysreplacewithanewone.
Torquewrenchtighteningspecificationsmustbestrictlyadheredto.
NOTE:Theillustrationsinthisdocumentshowtypicalconstructionofthedifferentassembliesand
maynotreproducethefulldetailorexactshapeoftheparts;however,theyrepresentpartsthathave
thesameorsimilarfunction.
Installationtimeisapproximately1.0hour.
PARTSTOBEINSTALLED
Item Description PartNumber QTY

3/9/2017 einstructiondetails
http://instructions.brp.com/content/instructionsheet/en_CA/einstructiondetails.html#articleNo=kA0a0000000l0rxCAA&lang=en_CA&title=SEADOO%20KIT…
2/16
P1 DepthFinder 278002954 1
P2 GelPad 293550042 1
P3 DepthFinderSupport 278002495 1
P4 DepthFinderBaseSupport 278001994 1
P5 WiringHarness 278002571 1
P6 3AmpMiniFuse 710001008 1

3/9/2017 einstructiondetails
http://instructions.brp.com/content/instructionsheet/en_CA/einstructiondetails.html#articleNo=kA0a0000000l0rxCAA&lang=en_CA&title=SEADOO%20KIT…
3/16
P7 M6x20PlastiteHexagonal
Screw 243162060 2
P8 LockingTie 414115200 10
VEHICLEPREPARATION
NOTE:RefertoappropriateShopManual.
SPARKModels:(TypeB)
Removethebody.
Unplugthebattery.DisconnectBLACK()batterycablethentheRED(+)cable.
WARNING
Alwaysdisconnectbatterycablesexactlyinthespecifiedorder.
GTI,GTS,GTR,WAKE155andRXTModels:(TypeB)or(TypeC)
Openthefronttrim.
Removeaccesspaneltoaccesstothebattery.
Unplugthebattery.DisconnectBLACK()batterycablethentheRED(+)cable.
WARNING
Alwaysdisconnectbatterycablesexactlyinthespecifiedorder.
Removeseat.
GTXandRXTwithsuspensionModels:(TypeA)(Models2015andbefore)
Opentherearwardboardingplatform.
RemovetheRHstoragetray(starboard).
Unplugthebattery.DisconnectBLACK()batterycablethentheRED(+)cable.
WARNING
Alwaysdisconnectbatterycablesexactlyinthespecifiedorder.
GTX,RXTandWAKEPROModelsWITHOUTsuspensionWITHrearaccesspanels:(TypeA)
OpentheRHrearaccesspanels.
RemovetheRHstoragetray(starboard).
Unplugthebattery.DisconnectBLACK()batterycablethentheRED(+)cable.

3/9/2017 einstructiondetails
http://instructions.brp.com/content/instructionsheet/en_CA/einstructiondetails.html#articleNo=kA0a0000000l0rxCAA&lang=en_CA&title=SEADOO%20KIT…
4/16
WARNING
Alwaysdisconnectbatterycablesexactlyinthespecifiedorder.
GTX,RXTandWAKEPROModelsWITHOUTsuspensionWITHOUTrearaccesspanels(TypeC)
Openseat.
INSTALLATIONINSTRUCTIONS
DepthFinderSupportInstallation
1.Locateareawheredepthfinderistobeinstalled.Seefollowingillustrationsforyourtypeofvehicle.
Toreachdepthfinderinstallationlocation,removethefollowingcomponents,ifapplicabletoyour
vehiclemodel:
Lowerdeck
Reargrabhandle
Coolantbottle
Exhausthosefromengine
Exhaust
Breatherhosefromengineairintake
Rearengineairintake.
DepthFinderInstallation
AllModels:
1.Installgelpadondepthfinder.
1.1Placetheflatsideofdepthfinderonalevelsurface.
1.2Cleantheconcavesurfaceofdepthfinder.
1.3Removebothprotectorsfromgelpad.
1.4Applygelpadondepthfinder.
NOTICE Makesurenottotrapairbetweengelpadanddepthfinder.Otherwise,the
devicemaynotworkproperly.
1.Gelpad[P2]
2.Depthfinder[P1]
(TypeA)Underthebattery(2015andbefore)
Removethetopoftheelectricalcomponentssupportandputaway.
1.Removeandkeepscrewssecuringbatteryholdertobatteryholderbase(oneoneachside).

3/9/2017 einstructiondetails
http://instructions.brp.com/content/instructionsheet/en_CA/einstructiondetails.html#articleNo=kA0a0000000l0rxCAA&lang=en_CA&title=SEADOO%20KIT…
5/16
PARTSREMOVEDFORCLARITY
1.Retainingscrews
2.Batteryholder
2.Unplugventhosefrombattery.
3.Removebattery(withbatteryholder)fromvehicle.
4.Installdepthfinderintobatteryholderbasewiththeharnesstowardthepump.
5.Pushonthedepthfinderuntilbothlockingtabsarelocked.Makesuredepthfinderlockingtabsare
wellengagedintosupportbracket.
1.Lockingtabs
2.Batteryholderbase
6.Routethedepthfinderharnessinthebatteryholderbasegroove.
7.Plugventhosetothetopofbattery.Makesureventhoseisnotpinchedorbent.
8.InstallthebatteryandsupportinvehicleusingpreciouslyremovedM8x40screws.
9.Tightenbatteryholderscrewstospecification.
Tighteningtorque
Batteryholderscrews 14±2 N•m(124±18 lbf•in)
(TypeB)Withscrewedbracket
NOTE:Ensuretoproperlyorientthesupportroundednotchtowardsthecenterofthehull.
1.Supportroundednotch

3/9/2017 einstructiondetails
http://instructions.brp.com/content/instructionsheet/en_CA/einstructiondetails.html#articleNo=kA0a0000000l0rxCAA&lang=en_CA&title=SEADOO%20KIT…
6/16
Tighteningtorque
M6x20PlastiteHexagonalScrew[P7] 7±.5 N•m(62±4 lbf•in)
1.Installthedepthfinderintoitssupportwithharnesspointingtowardscenterofhull.Squeeze
retainingtabstoeaseinsertion.
2.Pushonthedepthfinderuntilbothlockingtabsarelocked.
1.Depthfinder
2.Lockingtabslocked
(TypeC)Withgluedbase
1.Installdepthfindersupportasperfollowingillustrations.
serviceproducts
Isopropylalcohol Cleaninsideofhullatdepthfindersupportmountingarea
5minuteepoxyglue Gluedepthfindersupporttoinsideofhull
NOTE:Infollowingillustration,somehosesarenotshownforclarityofillustration.
TYPICALHULLPREPARATION
1.Cleanhullhere
2.Exhausttemperaturesensor
3.Bailerassembly
2.Prepareepoxyglueaspermanufacturers'instructions.
WARNING
Whenmixingandapplyingepoxyglue,alwaysrefertomanufacturersinstructions.
3.Applygenerousamountofepoxygluetobaseofdepthfindersupport.

3/9/2017 einstructiondetails
http://instructions.brp.com/content/instructionsheet/en_CA/einstructiondetails.html#articleNo=kA0a0000000l0rxCAA&lang=en_CA&title=SEADOO%20KIT…
7/16
DEPTHFINDERSUPPORTPREPARATION
1.Topofdepthfindersupport[P4]
2.Generousamountofepoxyglueappliedhere(bottomofsupport)
DEPTHFINDERSUPPORTINSTALLATION
1.Longitudinalaxisofwatercraft
2.Depthfinderlockingtabs
3.Highsideofdepthfindersupporttowardskeelofwatercraft
4.Allowsufficienttimeforepoxygluetosetbeforeinstallingdepthfinder.Refertomanufacturers'
instructions.
ElectricalConnections
2016andup
Refertoshopmanual
900HOModels
NOTE:Install(P/N295100599)followingtheprocedureincluded..
AccessoryFuseBoxPreparation
1.Disconnectandremoveaccessoryfuseboxfrombattery.Seefollowingillustrations.

3/9/2017 einstructiondetails
http://instructions.brp.com/content/instructionsheet/en_CA/einstructiondetails.html#articleNo=kA0a0000000l0rxCAA&lang=en_CA&title=SEADOO%20KIT…
8/16
1.Longaccessoryfuseboxharnessconnector
2.VehicleDLCholder
1.Shortaccessoryfuseboxharnessconnector
2.VehicleDLCconnector
TYPICAL
1.Releasefuseboxfromitssupporthere
2.Removeaccessoryfuseboxcover.
3.Removeallbusbarsfromaccessoryfusebox.
1.Busbarstoremove
4.Locateandremovethefollowingsealplugsfrombackofaccessoryfusebox:A3,B3,C3,D3,D5,
andD6.
NOTE:Fuseboxcontactcoordinatesaremoldedonthebackofthefusebox.

3/9/2017 einstructiondetails
http://instructions.brp.com/content/instructionsheet/en_CA/einstructiondetails.html#articleNo=kA0a0000000l0rxCAA&lang=en_CA&title=SEADOO%20KIT…
9/16
CONTACTCOORDINATES
5.Insertwireterminalsofwiringharness[P5]intofuseboxcontactcoordinatesasperfollowingtable.
WiringHarness(P5)connectiontofusebox
Wirecolor Fuseboxcontactposition
Red/Whitewire
A3
D6
Black B3
White/Black C3
White/Red D3
Purple D5
6.Completefuseboxconnectionandinstallationasperfollowingillustrations.
1.Installbusbars
2.Installfuse[P6]
Step1:.Installfuseboxcover

3/9/2017 einstructiondetails
http://instructions.brp.com/content/instructionsheet/en_CA/einstructiondetails.html#articleNo=kA0a0000000l0rxCAA&lang=en_CA&title=SEADOO%20KIT…
10/16
Step2:.Installfuseboxonitssupport
SHORTFUSEBOXHARNESSCONNECTION
1.Shortaccessoryfuseboxharnessconnector
2.VehicleDLCconnector
LONGFUSEBOXHARNESSCONNECTION
1.Longaccessoryfuseboxharnessconnector
2.VehicleDLCholder
1.Accessoryfusebox
2.Depthfinderlocation
3.Wiringharnessrouting
NOTE:Thedepthfinderwiringharnessisroutedbehindbothenginemountsinthebottomofthehull,
undertheengine.

3/9/2017 einstructiondetails
http://instructions.brp.com/content/instructionsheet/en_CA/einstructiondetails.html#articleNo=kA0a0000000l0rxCAA&lang=en_CA&title=SEADOO%20KIT…
11/16
1.LHrearenginesupport
2.Steeringcable
1.Steeringcable
2.LHfrontenginesupport

3/9/2017 einstructiondetails
http://instructions.brp.com/content/instructionsheet/en_CA/einstructiondetails.html#articleNo=kA0a0000000l0rxCAA&lang=en_CA&title=SEADOO%20KIT…
12/16
1.Steeringcable
2.Fusebox
7.Reconnectbattery.
WARNING
Alwaysreconnectpositive(+)batteryterminalfirst,negative()terminallast.
Step1:.Reconnectpositive(+)terminalfirst
Step2:.Reconnectnegative()terminallast
8.Carryoutatestofthedepthfinderoperation,refertoDRYTESTINGOFDEPTHFINDER.
ElectricConnection
AllModelsexcept900HOModels(2015andbefore)
1.DisconnectBLACK()batterycablethentheRED(+)cable.
WARNING
Alwaysdisconnectbatterycablesexactlyinthespecifiedorder.

3/9/2017 einstructiondetails
http://instructions.brp.com/content/instructionsheet/en_CA/einstructiondetails.html#articleNo=kA0a0000000l0rxCAA&lang=en_CA&title=SEADOO%20KIT…
13/16
TYPICAL
1.BLACK()cablefirst
2.RED(+)cablelast
2.Liftandpushtopofelectricalcomponentsupporttounlockitfrombatteryholder.Movesupport
asidetomakeroom.
TYPICALTOPVIEW
1.Electricalcomponentsupport
1.Lowerreceptacle
2.Upperretainingtab
AllModelsWITHOUTrearaccesspanels
Routewiringharness[P5]fromfuseboxtodepthfinderalongmainwiringharness.Secureitusing
lockingties[P8]every400 mm(16 in)alongtheway.
NOTICE Keepwireharnessawayfromsharpedgesandmoving,rotatingorhotparts.
Regroupthewireexcessneartothebatteryandsecurewithlockingties[P8].
AllModelsWITHrearaccesspanels
Regroupthewireexcessneartothebatteryandsecurewithlockingties[P8].

3/9/2017 einstructiondetails
http://instructions.brp.com/content/instructionsheet/en_CA/einstructiondetails.html#articleNo=kA0a0000000l0rxCAA&lang=en_CA&title=SEADOO%20KIT…
14/16
1.Connectdepthfinderconnectortonewwiringharness.
2.ConnectRED(+)batterycablefirst,thentheBLACK()cable.
WARNING
Alwaysconnectbatterycablesexactlyinthespecifiedorder.
TYPICAL
1.RED(+)cablefirst
2.BLACK()cablelast
3.RefertoDRYTESTINGOFDEPTHFINDERtoensuredepthfinderoperation.
4.Reinstallallotherremovedparts.
WARNING
Neverusethedepthfinderasawarningdevicetorideinshallowwater.Useitasanavigationguide
only.Nottobeusedtogetprecisenavigationdata.
DRYTESTINGOFDEPTHFINDER
Allmodels
1.Youneedacontainer(cup,glassoranemptywatercraftsecuritycontaining).
2.Removelidfromthewatercraftsafetyequipmentcontainer.Emptythecontainer.
3.Installthetethercordontheenginecutoffswitch.
4.Momentarilypressthestartbuttontoenergizetheelectricalsystem.
5.RepeatedlypresstheMODEbuttononthemultifunctiongaugeuntilDEPTHisdisplayed.
6.Placetheemptysafetyequipmentcontaineronlowerhulldirectlybeneaththedepthsounder.

3/9/2017 einstructiondetails
http://instructions.brp.com/content/instructionsheet/en_CA/einstructiondetails.html#articleNo=kA0a0000000l0rxCAA&lang=en_CA&title=SEADOO%20KIT…
15/16
Pleasenotethatanemptymetalcontainercanalsobeusedtoperformthistest.
Thegaugeshouldprovideareading.Thereadingmayincreaseanddecreaseduringthetest
however,thegaugewillalwaysprovideanumericaldepthindicationifthedepthfinderisworking
properly.
CORRECTVIEWONGAUGEIFDEPTHSOUNDERISWORKINGPROPERLY
Ifdepthfinderprovidesanumericalindicationaspreviouslyillustrated,nomoreactionisrequired.
Ifdepthfinderprovidesanindicationofonlydashes(nonumbers),theremaybeairtrappedbetween
thedepthfinderandthegelpad.Ifthisisthecase,thegelpadmustbereplaced.
INCORRECTVIEWONGAUGE
REINSTALLATIONOFDEPTHFINDER
Sincethegaugeprovidedabadreading,itispossiblethatthereisanairgapbetweenthebaseofthe
depthfinderandthehull.Carryoutthefollowingsteps.
1.Removedepthfinder.
2.Removegelpadfromdepthfinder.
3.Thoroughlycleantheareawherethedepthfinderwillbereinstalled.
4.Applygelpadtothefaceofthedepthfindersoitcoverstheentirematingsurface.

3/9/2017 einstructiondetails
http://instructions.brp.com/content/instructionsheet/en_CA/einstructiondetails.html#articleNo=kA0a0000000l0rxCAA&lang=en_CA&title=SEADOO%20KIT…
16/16
1.Gelpad[P6]
2.Depthfinder[P1]
5.Reinstalldepthfinder.
6.Drytestdepthfindertoensureyouobtainaproperreading.
DepthFinderTroubleshooting
DepthfinderTROUBLESHOOTING
SYMPTOM POSSIBLECAUSE REMEDY
NOTHINGisdisplayedinthe
informationcenter
Depthfindernotconnected. Connectitproperly.
12Vorgroundwireopento
depthfinder.
Checkfuseandwiring
harnesses.
Problemwiththe
communicationlinkwires.
CheckWHITE/BLACKand
WHITE/REDwirestoCAN
busbarsinfusebox.
(ftorm)isdisplayedand
SENSORisblinkingafterself
testfor5seconds
Watercraftisnotinwater. Launchwatercraftinwaterand
recheck.
Thereisairbetweengelpad
anddepthfinderorbetween
depthfinderandhull.
Removedepthfinder.Replace
gelpad.
Depthfinderisdefective. Tryanewdepthfinder.
Reinstallallremovedcomponents.

