Sea-doo SEASCOOTER Aquanaut ZS19 User manual

English Version
CAUTION
ELECTRICALLY OPERATED PRODUCT
Not recommended for children under 8 years of age. As with all
electrical products, precautions should be observed during handling
and used to reduce the risk of electric shock.
User Manual
SDP95001
Model no. ZS19 / SD5543
Distributors in the United States and Canada provide a standard Limited
Warranty for 6 months from the date of purchase for new products. If
you're not located in the United States or Canada, please contact your
local distributor for warranty arrangements in your territory. Please visit
www.seadooseascooter.com for distributor / Service Centre details.
Distributors ONLY warrant Stallion products purchased from an
authorized dealer.
Ask your local Distributor for the warranty period in your region by calling their
Service Center. Any part of the product supplied by the Distributor and found in the
reasonable judgment of the Distributor to be defective in material or workmanship
will be repaired or replaced by the Distributor without charge for parts or labor. The
product including any defective part must be sent to the Distributor within the
warranty period. The customer will pay for the expense of delivering the product to
the Distributor. The Distributor will pay for the expense of returning the product to
the customer.
ALWAYS ACTIVATE YOUR WARRANTY IMMEDIATELY ON
http://www.seadooseascooter.com/warranty.html
www.seadooseascooter.com
W A R R A N T Y & C U S TO M E R
S E RV I C E I N F O R M AT I O N
Distributors ONLY warrant products with an active
Warranty Registration
SEE NEXT PAGE

Contents
Introduction 1
Parts diagram 2
WARNING & CAUTION 3
Getting Started 5
Battery use 7
Care & Maintenance 14
- Storing the Aquanaut 14
- Rechargeable Battery and Charger Care 14
- Accidental Flooding 15
- Removing Blockage From Propeller 16
Trouble Shooting 18
Technical Specifications 19
FFC Statement 20

Parts DiagramInstruction
The SEA-DOO®SEASCOOTER™ Aquanaut gives
kids a totally new experience - power performance for
fun and excitement in the pool.
Please take a little time to study this manual before
using your Aquanaut.
21
Fig.1
Nose Cone
Nose Cone Seal
Latch
Nozzle
Propeller
On/off Trigger
Master Switch
Rechargeable Battery
Charger
Battery Clip
Charger Jack
7
8
9
10
11
1
2
3
4
5
6
10
11

WARNING
WARNING:
CHOKING HAZARD - Small parts
Not for children under 3 years
This is not a life saving device. Do not leave children
unattended while device is in use.
Only to be used in water in which the child is within its
depth and under supervision.
•Read the User Manual carefully before using the
AQUANAUT.
• Keep the packaging since it contains important information.
• Do not operate the AQUANAUT for long periods out of the
water to avoid damage.
• The AQUANAUT must be assembled by an adult.
•The AQUANAUT is designed to hold ONE person not
exceeding 100 lbs/45kg.
•always wear a Approved Personal Flotation Device /
Approved Life-Preserver when using the AQUANAUT.
• Not to be used by children under the age of eight (8) and
must ONLY be used by children under adult supervision.
An adult must be responsible for battery safety at all times,
during use, storage and charging.
• The AQUANAUT is for pool use only - DO NOT use in the
open sea.
• Never stick body parts, clothing or other objects in the
vicinity of the propeller.
•DO NOT wear loose or flowing clothing that could be
drawn into the propeller.
•Particular care should be exercised when using the
AQUANAUT near anybody with long hair.
• User with long hair should tie it up or wear a swimming cap
when using the AQUANAUT.
• ALWAYS inspect the area to ensure it is free of hazards or
obstacles such as swimmers before using the AQUANAUT.
• ALWAYS ensure sufficient charges remains in the battery
to return to the poolside before using the AQUANAUT.
•Always charge battery to its fullest before using the
AQUANAUT. After charging is complete the battery will
continue to off gas. Wait at least 30 minutes after charging
before removing the battery from the charger or placing the
battery into the battery housing. Failure to do so could
result in an explosion.
• ALWAYS remove the battery from the unit when not in use.
• Do not use alcohol or mind-altering drugs prior to using this
product.
• ALWAYS keep the AQUANAUT out of direct sunlight when
not in use. HEAT KILLS BATTERIES.
• DO NOT store the battery in the unit.
4
3
WARNING

56
When you buy the SEA-DOO®SEASCOOTER™
AQUANAUT the battery is disconnected and needs to be
charged.
Follow the safety cautions on page 7 to 10 and charging
instructions on pages 11 to 13.
Using the AQUANAUT
1. Charge the battery and install just before use.
2. Make sure your child is wearing a coast guard approved
flotation device when using the Aquanaut.
3. Place the Aquanaut into the water. The Aquanaut should
float.
4. When ready to set off, switch the Master Switch to the
'On' position. (see fig. 2)
Getting Started
Fig.2
'On' position
5. Pull and hold the trigger to start the propeller. (There is
a short delay before the Propeller begins to rotate).
6. To stop the propeller, simply release the trigger.
7. Always set Master Switch to the 'Off' position when out
of the water. (see fig. 3)
Fig.3
'Off' position

CAUTION
• Your SEA-DOO®SEASCOOTER™ AQUANAUT is supplied
with a battery that needs to be treated carefully as it will
release potentially explosive gasses during its normal cycle
of use (off gassing). Please read the entire manual
thoroughly and follow all instructions. Failure to do so can
result in an explosion occurring.
• Always remove the battery from your SEA-DOO®
SEASCOOTER™ AQUANAUT when it is not in use and
store separately in a well ventilated area where it is out of
the reach of children and away from heat and ignition
sources.
• Do not install the battery in your
SEA-DOO®SEASCOOTER™
AQUANAUT until immediately prior to using it.
• Before disconnecting/connecting any cables, open the nose
cone and allow two minutes for any explosive gases to
dissipate.
• Do not use/store/charge the battery in temperatures above
40ºC (104ºF) as excessive off gassing may occur. Keep the
battery and AQUANAUT in the shade when not in use.
• Always ensure the unit is dried thoroughly before opening
the Nose Cone.
• Only use the charger supplied with the SEA-DOO®
SEASCOOTER™ AQUANAUT.
• The battery supplied with your
SEA-DOO®SEASCOOTER™
AQUANAUT releases a potentially explosive gas during
charging. Charging should only take place in a well
ventilated area, away from children and naked flames or
other ignition sources (cigarettes, sparks). Never charge the
battery whilst still in the SEA-DOO®SEASCOOTER™
AQUANAUT.
Battery Use
87
Battery Use
RE-CHARGE THE BATTERY
3
3
AT LEAST
www.seadooseascooter.com
• Must remove and store
the battery separately from
the unit when not in use!
• Must re-charge the battery
after use WITHIN 24 HOURS.
• Must re-charge the battery
at least EVERY THREE MONTHS
when not in use.
User Manual must be read
and understood before use.
No warranty for the battery,
Please read and follow the
Battery Safety Instruction
Incorrect battery maintenance
may reduce the battery life
and influence its function.
MONTHS
EVERY
MONTHS

CAUTION
• Charge the battery as soon as possible after use within
24 hours.
• Always charge the battery to the fullest before using the
SEA-DOO®SEASCOOTER™ AQUANAUT.
• Always remove the battery from the battery housing before
charging.
• Always connect charger jack to the battery first and then
plug charger into the mains.
• After charging, disconnect from the mains first and then
disconnect the battery from the charger.
• After charging is complete the battery will continue to off
gas. Wait at least 30 minutes after charging before removing
the battery from the charger or placing the battery into the
battery housing. Failure to do so could result in an
explosion.
• Do not place battery into your SEA-DOO®SEASCOOTER™
AQUANAUT until immediately before use.
• Remove battery from charge once fully charged.
• Never charge the battery in a sealed container.
• Never charge the battery near water.
• Never short circuit the battery or battery connectors.
• Always ensure the charger is dry before use.
• The charger gets quite warm in use – this is normal.
• If in doubt of the state of the battery, recharge it until
the indicator on the battery charger indicates a full charge.
Battery Use
CAUTION
• If the battery is not to be used for an extended period, store it
in a well ventilated area away from children, heat and ignition
sources and recharge it every three months to maintain
charge and avoid excess off gassing. DO NOT store the
battery inside the SEA-DOO®SEASCOOTER™ AQUANAUT.
• If the battery appears damaged or will not charge fully, the
battery must be replaced. If battery life is noticeably reduced,
the battery should be replaced.
• Exhausted batteries are to be removed from the toy.
• Battery must be recharged under adult supervision.
• ALWAYS charge battery in a well-ventilated place out of
reach of children.
• The battery supplied with your SEA-DOO®SEASCOOTER™
AQUANAUT should last about 200 cycles or two years before
it should be replaced. Please contact your local customer
service centre/distributors. Using a battery in excess of these
recommendations can result in excessive off gassing of
explosive gas.
• The Rechargeable Battery will give you approximately one
hour of use - always make sure you have enough power left
to return to the poolside.
• Any battery charger/transformer to be used with the toy
should be regular examined for potential hazards, such as
damage to the cable or cord, plug, enclosure or other parts,
and that, in the event of such damage, the toy must not be
used until that damaged has been properly removed.
• When the SEA-DOO®SEASCOOTER™ AQUANAUT speed
drops it is time to recharge the battery. Do not continue to use
the SEA-DOO®SEASCOOTER™ AQUANAUT after the
speed drops, until it stops, otherwise the battery will be
damaged.
Battery Use
109

Battery and Charger Ratings:
Rechargeable Battery: 12V/4.5Ah
Charger: Output 12V/500mA
Charging The Rechargeable Battery
For battery charging follow these instructions.
1.Always ensure that the Master Switch is in the 'Off'
position. (see fig. 3)
2.Always ensure that the Aquanaut is out of the water, dry
and placed in a dry area.
3.
Unclip the latches and remove the Nose Cone. (see fig. 4)
4.Allow two minutes for any gasses to dissipate.
5.Disconnect the battery cable from the housing cable
(if not already disconnected - the cable will be
disconnected when you buy your Aquanaut) (see fig. 5)
11
6. Remove the battery from the Aquanaut and place on a
level surface.
7. Connect the battery cable to the charger cable.
8. Plug charger into mains, and turn on the supply.
9. Charging will take 10-12 hours for a fully discharged
battery. When the battery is charging the red LED is on,
when the battery is charged the green LED turns on.
10. Unplug the charger from the mains.
11. Allow battery to stand for 30 minutes before using it.
12. Unplug the battery cable from the charger cable.
13. When ready for use, install battery and reconnect to
the housing cable.
14. Make sure the Nose Cone Seal. (see fig. 6) is clean
and lubricated with silicone grease (you can buy this at
your local hardware store).
Fig.4
A
B
Fig.5
Nose cone
Seal
Battery
Battery
Clip
Fig.6
12

CareAnd Maintenance
1413
15. Replace the Nose Cone and turn and lock the latches -
you will hear a click when they are locked. (see fig.7)
The Aquanaut is now ready to be used.
Replacing a flat battery with a fully charged battery.
1.Follow the steps 1 to 5 above
2.Remove the flat battery.
3.Install the charged battery.
4.Follow steps 13 and 15.
Buying Rechargeable Batteries
It is a good idea to have a second battery so that when
one has run out you can swap it over with a charged
one. Contact your local customer service
centre/distributor to purchase additional rechargeable
batteries.
Storing the Aquanaut
1. Always rinse the Aquanaut in fresh water and allow it to dry
before storage.
2. Open the Nose Cone and remove the Rechargeable
Battery (see also section on Rechargeable Battery and
Charger Care for more storage information).
3. DO NOT store battery inAquanaut.
4. Store the Aquanaut in the original box in a dry place.
- ambient temperature for storage should be within
- 20oC to 40oC (-4oF to 104oF).
5. Always store the Aquanaut vertically.
Rechargeable Battery and Charger Care
1. Please read and understand important Battery Use safety
information on pages 7, 8, 9 and 10.
2. The battery supplied with your SEASCOOTER™ should
last about 200 cycles or two years before it should be
replaced. Please contact your supplier. Using a battery in
excess of these recommendations can result in excessive of
gassing of explosive gas.
3. ALWAYS remove the battery from the SEASCOOTER™
immediately after use.
4.DO NOT STORE BATTERY IN SEASCOOTER™
A
BFig.7

15 16
Accidental Flooding
Always sure the Nose Cone Seal (see fig.6) is clean,
lubricated with silicone grease and undamaged and the
Nose Cone Latches are fully closed.
However, should the seal not to be cleaned properly or the
latches are not fully closed and water enters the battery
compartment, your Aquanaut will not be permanently
damaged since it is designed for protection against
flooding.
If the Battery Compartment floods:
1. Remove the Aquanaut from the water immediately and
set the master switch to locked position. (see fig.3)
2. Unclip the latches and remove the Nose Cone and tip
out excess water. (see fig.4)
3. Wait two minutes for any gases to dissipate.
4. Unplug the rechargeable battery and remove from the
Aquanaut and dry completely.
5. If salt water has entered, rinse battery and battery
housing with fresh water.
6. Dry housing and battery thoroughly.
7. Check rechargeable battery for damage, if it shows any
sign of damage contact customer service for a
replacement.
8. Reinstall the rechargeable battery and reconnect to the
housing cable.
9. Make sure the Nose Cone Seal (see fig.6) is clean and
lubricated with silicone grease and undamaged.
10.Replace the Nose Cone and turn and lock the latches -
you will hear a click when they are locked. (see fig.7)
Removing Blockage From Propeller
If the propeller is blocked:
1. Remove the Aquanaut from water and dry completely.
2. Make sure the Master Switch is in the 'Off' position.
(see fig.3)
3. Remove battery - see page 11, steps 1 to 5.
4. Unscrew rear grille screw and remove Nozzle. (see fig. 8)
5. Straighten and then remove the split pin. (see fig.9)
Fig.8
Fig.9
Rotate the
Split Pin 90º
Slide out the
Split Pin and remove
the propeller
Split Pin Locked Bend legs to
straighten them
12
3
ENLARGED
VIEW
4