Sealey TB18LEDW User manual

2PC WIRELESS LED TRAILER LIGHT SET
MODEL NO: TB18LEDW
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGEAND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9Check the battery status, ensure the lights are functioning correctly before using.
9Please check that each light function works normally before using.
9When the lights are in storage, check the batteries every 6 months.
9You must complete the paring process when using replacement & additional lights.
9Regularly check the lights after long periods of use.
2. INTRODUCTION
Magnetic wireless light clusters give essential light functions with no wiring required. Suitable for metal trailers and farming vehicles up to
20m long. Designed and manufactured for trailer, lorry, agricultural machinery, tractor, and other vehicles. EU Plug wiring congurations and
vehicles tted with a 7-pin plug towing trailers. Three functions: brake, indicator, and tail light. Five functions: brake lights, rear turn signal
lights, rear position lights, license plate lights, and return reectors. Supplied in storage case.
3. SPECIFICATION
LED Type: .....................................................24 x 0.2W SMD
Voltage:............................................................................12V
IP rating: .........................................................................IP65
Fixing:......................................................................Magnetic
Working Temperature Range: ........................-30°C to +50°C
3.1. The battery fitted to this light is considered to be a consumable item and its ability to accept charge will reduce over time. We will
warranty it against mechanical and electrical defect for a period of one year, this does not cover fair wear and tear. If the battery is not
properly charged before first use, or regularly conditioned, its capacity will diminish. Under these circumstances we will not replace the
battery even if it is less than one year old.
4. INSTALLATION
TB18LEDW Issue 1 23/06/2021
Original Language Version
© Jack Sealey Limited
Refer to
instructions
MOUNTING POSITIONS FOR TRAILER REAR LAMPS AND
REFLECTORS
All lamps and reectors should be mounted symmetrically. Trailers over 1.3M wide require at least one rear red fog
lamp, and it must be mounted on the centre line or to the o󰀨side of the trailer. If twin rear fog lamps are tted they
should be mounted symmetrically. Trailers over 1.6M wide require white front reectors and white front markers/
lamps. Trailers manufactured from October 2012 tted with brakes require a reversing light. Trailers over 5M long
may require side retro reectors and side marker lamps. Trailers 6M long and over require red/white side markers.
The above information is given as a guide only; for full details consult:
'The Road Vehicle Lighting Regulations'.
400 Minimum
(also twin fog lamps if tted)
400 Max 400 Max
TRIANGULAR REFLECTORS
(must be above indicators)
INDICATORS STOP/TAIL
FOG LAMP/S
250 min
100 Minimum separation
between stop and tail light
1000 max
350 Min
1500 Maximum
900 Maximum
Dimensions are in millimetres
All lamps must be ‘E’ marked

4.1. TRAILER WIRING CODES (N-TYPE)
4.1.1. “N” Type
Pin 1 Yellow Left hand direction indicator lamp
Pin 2 Blue Rear fog lamp/lamps
Pin 3 White Common return (earth)
Pin 4 Green Right hand direction indicator lamp
Pin 5 Brown Right hand tail lamp/ Rear registration lamp
Pin 6 Red Rear stop lamps
Pin 7 Black Left hand tail lamp/ Rear registration lamp
4.2. Plug the transmitter into the socket on the vehicle.
4.3. Turn on both the light units. The left hand green light bar (on the battery indicator) will ash when the unit has been switched on.
4.4. Start the vehicle and turn on the hazard lights.
5. OPERATION
WARNING! When the red light on the low battery indicator is ashing charge the light.
5.1. PAIRING THE DEVICE
5.1.1. Hold down the pairing button for 5 seconds. The right hand orange light (on the battery indicator) will illuminate when pairing is in
progress. The light will go out when pairing is complete.
NOTE: Always charge the lights to full before any long distance travel.
g.1
g.2 g.3
TB18LEDW Issue 1 23/06/2021
Original Language Version
© Jack Sealey Limited

5.2. CHARGING THE LIGHTS
5.2.1. Make sure both units are charged and functioning correctly before use.
5.2.2. The red light will ash to indicate the battery level.
5.2.3. Use the USB cable provided to charge both units simultaneously.
6. MAINTENANCE
9When the lights are in storage, check the batteries every 6 months.
9Clean the lights with a damp cloth and make sure they are completely dry before storing.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
BATTERY REMOVAL
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack
Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 24 months from purchase date, proof of which is required for any claim.
TB18LEDW Issue 1 23/06/2021
Original Language Version
© Jack Sealey Limited