Sealey AP6572 User manual

INSTRUCTIONS FOR:
RACKING UNIT WITH 4 MESH SHELVES
900KG CAPACITY PER SHELF
MODEL NO: AP6572
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.1 GENERAL SAFETY
WARNING! Ensure Health & Safety, and local authority regulations
are adhered to when assembling and using these shelves.
Locate shelves in a suitable area where they will not be an
obstruction.
Keep the general area clean, uncluttered and ensure there is
adequate lighting.
WARNING! Erect shelves on a level and solid surface such as
concrete.
Keep children and unauthorised persons away from the storage
area.
DO NOT use the shelves for any purpose other than that for
which they are designed.
DO NOT site the shelves out of doors.
DO NOT get the shelves wet or use in damp or wet locations or
areas where there is condensation.
DO NOT clean the shelf suports with any solvents which may
damage the coated surface.
Ensure that the shelves are properly assembled before loading
them with heavy items.
Maximum load for each shelf is 900kg.
Where possible the unit should be fixed to the wall with
suitable fixings
Place heavier items on the lower shelves.
Where possible heavier items should be evenly distributed across
the shelves.
3. CONTENTS
2. INTRODUCTION
Carefully unpack the product and check the contents (fig.1)
against the list below. Should any items be missing or damaged
make immediate contact with your Sealey dealer.
Part Description........................................................... Quantity.
A Upright Frame .............................................................................2
BCross Beam.................................................................................8
CWire Mesh Shelves .....................................................................4
4. ASSEMBLY
4.1 We recommend that this shelving unit be assembled by two
people. The only tool required is a rubber mallet. Do not use a
hard faced hammer as this will damage the surface finish of the
cross beams. Make sure that all the clips lock in place securely
before using the unit. Do not use any parts that are damaged
and/or distorted as these may assemble incorrectly and result in
an installation that is unsafe and which may cause injury or
damage when the shelves are loaded.
Fig.1
4.2 See Fig.2. Support one end frame 'A' in a vertical position and
attach the end of one cross beam 'B' to it at the base of one of
the uprights. Ensure that both tags on the end bracket engage
properly with the slots in the upright as shown in the inset
diagram above. Tap the cross beam gently next to the end
bracket so that the beam is properly seated into the slots in the
upright. Connect the other end of the beam to the second end
frame at the same height and tap into place.
4.3 Attach another cross beam 'B' to the other side of the end frames
'A' ensuring that it is at the same level as the first cross beam.
Fully painted steel frame with four heavy-duty mesh shelves.
Industrial structured beams offers added strength with 900kg
capacity per level, giving a maximum capacity of 3600kg per
rack. Boltless design means no tools required to assemble. Clips
together in minutes. Suitable storage solution for workshop, body
shop, warehouse and agricultural environments.
Height: 1828mm Width: 1830mm Depth: 600mm
Fig.2
AP6572 + AP6572E ISSUE NO:2 04/11/08
INCORPORATING EXTENSION PACK WITH 4 MESH SHELVES MODEL NO: AP6572E

4.4 See Fig.3. Continue to assemble the next two pairs of cross
beams at the heights required. The end frames allow adjustment
in 3" increments. Each pair of beams must be mounted at the
same height. Ensure that all tabs on the cross beam brackets are
fully engaged in the slots in the uprights and that the cross
beams are properly tapped down into place.
4.5 See Fig.4. Assemble the remaining two cross beams to the top
of the frame as shown below ensuring that the tabs are fully
engaged into the end frames.
4.6 See Fig.5. Each wire deck 'C' is reinforced with four cross
members welded onto the underside of the mesh. Each of these
cross members has a turned down tab at either end that must
pass through slots in the cross beams. Place a wire deck onto
each pair of cross beams as shown below ensuring that it sits
into the recessed section on the top surface of each cross beam
and all tabs pass through the slots in the cross beams as shown
in the inset diagram at the bottom of Fig.5.
4.7 See Fig.6. Extra components are available to create extra
storage bays as required (see Section 3). In the example below a
third storage bay is achieved by joining two free standing units .
Fig.5
Fig.3
Fig.4
Fig.6
AP6572 + AP6572E ISSUE NO:2 04/11/08
01284 757500
01284 703534
[e-mail]
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
www.sealey.co.uk
Web
email
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.

AP6572 + AP6572E ISSUE NO:2 04/11/08
EXTENSION PACK
MODEL NO: AP6572E
1.0 We recommend that this extension unit be
assembled by two people. The only tool
required is a rubber mallet. Do not use a hard
faced hammer as this will damage the surface
finish of the cross beams. Make sure that all
the clips lock in place securely before using the
unit. Do not use any parts that are damaged
and/or distorted as these may assemble
incorrectly and result in an installation that is
unsafe and which may cause injury or damage
when the shelves are loaded.
2.0 See Fig.A. Support one end frame 'A' in a
vertical position and attach the end of one
cross beam 'B' to it at the base of one of
the uprights. Ensure that both tags on the end
brackets engage properly with the slots in the
uprights as shown in the inset diagram. Tap the
cross beam gently next to the end bracket so
that the beam is properly seated into the slots
in the upright. Connect the other end of the
beam to the existing racking unit at the same
height and tap into place.
3.0 Attach another cross beam 'B' to the other side
of the end frames 'A' ensuring that it is at the
same level as the first cross beam.
4.0 See Fig.B. Continue to assemble the next
three pairs of cross beams at the heights
required. The end frames allow adjustment in
3" increments. Each pair of beams must be
mounted at the same height. Ensure that all
tabs on the cross beam brackets are fully
engaged in the slots in the uprights and that
the cross beams are properly tapped down into
place.
5.0 See Fig.C. Each wire deck 'C' is reinforced
with four cross members welded onto the
underside of the mesh. Each of these cross
members has a turned down tab at either end
that must pass through slots in the cross
beams. Place a wire deck onto each pair of
cross beams as shown ensuring that it sits into
the recessed section on the top surface of
each cross beam and all tabs pass through the
slots in the cross beams as shown in the inset
diagram at the top of Fig.C.
Fig.A
Fig.B
Fig.C
Carefully unpack the product and check the
contents against the list below. Should any
items be missing or damaged make immediate
contact with your Sealey dealer.
Part Description ..................................Qty.
A Upright Frame ............................................1
BCross Beam ...............................................8
CWire Mesh Shelves ....................................4