Sealey APMS82 User manual

INSTRUCTIONS FOR
MODULAR 3 DRAWER CABINET WITH
WORKTOP 665MM
MODEL NO: APMS82
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. GENERAL SAFETY
WARNING! Use the cabinet on level and solid ground, preferably concrete. Avoid tarmacadam since the cabinet may sink into
the surface.
9Locate the cabinet in a suitable working area.
9Keep the cabinet clean and tidy in accordance with good workshop practice.
9Keep children and unauthorised persons away from the working area.
9Take care of sharp edges when assembling.
8DO NOT use the cabinet for any purpose other than that for which it is designed.
8DO NOT use the cabinet outside.
8DO NOT get the cabinet wet or use in damp or wet locations or areas where there is condensation.
8DO NOT clean the cabinet with any solvents which may damage the surfaces.
Note: The assembly of this product may require assistance.
2. INTRODUCTION
Modular storage system ideal for any garage or workshop. Can be easily adjusted and upgraded to suit specic needs. Purchase a simple
base cabinet or create a custom storage system.
Standard features include:
• Ball bearing drawer slides throughout.
• Base cabinets are supplied with a worktop as standard.
• Floor cabinets feature adjustable shelves.
• Each unit is supplied with a lock and two keys.
• Supplied at packed and will require some simple assembly.
• Two door oor and wall cabinets feature perforated pegboard panels on the inside of the doors.
3. SPECIFICATION
Model No. ........................................................ APMS82
Overall Size (W x D x H) .................665 x 460 x 820mm
X-Large Drawer(x3) ........................570 x 370 x 215mm
APMS82 | Issue 1 13/02/18
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear protective
gloves
Wear safety
footwear

4. CONTENTS
4.1. Check contents prior to assembly.
4.2. Contact stockist with regard to any discrepancy.
5. ASSEMBLY
5.1. Assemble drawers as per g.2.
APMS82 | Issue 1 13/02/18
Original Language Version
© Jack Sealey Limited
g.1
g.2

5.2. Attach feet to base and corner supports for side panels as per g.3.
5.3. Attach sides of cabinet as per g.4.
5.4. Position the cabinet top in place and x using screws provided as per g.4.
APMS82 | Issue 1 13/02/18
Original Language Version
© Jack Sealey Limited
g.3
g.4

5.5. Square the frame. Make sure the measurements from corner to corner are equal in distance before tightening the bolts.
5.6. Position back panels and x in place as per g.5.
5.7. Ensure all screws are in place and have been tightened.
5.8. Attach top work surface as per g.6.
5.9. Position a drawer on a set of runners and push it carefully until it stops. If the operation is not smooth remove drawer and repeat.
5.10. Repeat for other drawers.
5.11. If the drawer needs to be removed pull the draw all the way out, then push the plastic release leaver on the ball bearing slides one up
and one down as shown. g.6. Then pull the drawer completely out.
APMS82 | Issue 1 13/02/18
Original Language Version
© Jack Sealey Limited
g.5
g.6

N.B. Maximum weight limit drawers:- 25Kg
Maximum weight limit cabinet:- 150Kg
APMS82 | Issue 1 13/02/18
Original Language Version
© Jack Sealey Limited
g.7
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.