Sealey SCR92 User manual

MECHANIC’S DETAILING UTILITY SEAT
MODEL NO: SCR92
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this seat.
9Locate seat in a suitable working area.
WARNING! Use seat on level and solid ground, preferably concrete.
9Keep the seat clean and tidy in accordance with good workshop practice.
8DO NOT use the seat for any purpose other than that for which it is designed.
8DO NOT stand on the seat.
8DO NOT use the seat outdoors.
8DO NOT get the seat wet or use in damp or wet locations or areas where there is condensation.
8DO NOT clean the seat with any solvents which may damage the paint surface or the protective coating on the padded seat base.
8DO NOT use if damaged.
2. INTRODUCTION
Extra thick cushioned padding for added comfort when seated. Suitable for use in Bodyshop and Detailing environments as well as general
garage use. Easy-rolling Ø100mm rubber castors with ball-bearing swivel. Storage trays and sliding draw for tools and components.
3. SPECIFICATION
Model No....................................................................SCR92
Capacity:......................................................................150kg
Overall Size (W x D x H).........................550 x 420 x 375mm
4. CONTENTS
1 Cushion
2 Top Frame
3 Drawer Holder
4 Drawer
5 Front Frame
6 Rear Frame
7 Side Tray A
8 Side Tray B
9 Steel Base
10 Casters (2 with Brake) Lock Nuts included
11 Bolt
12 Washer
13 Lock Nut
5. ASSEMBLY
5.1. Mount the rear panel (6) to the steel base(9) with
2 bolts (11) washers (12) and lock nuts (13).
5.2. Slide the drawer holder (3) into the rear panel (6) with seat holder (2) on the top, lock the seat holder (2) with the rear panel (6) by 2
bolts (11).
5.3. Clip the front panel (5) to the front with steel base (9), drawer holder (3) and seat holder (2) in place, lock the bottom 2 holes with
bolts, washers, and lock nuts (11,12,13). Lock top 2 holes with 2 bolts (11).
5.4. Mount 4 wheels (10) to the steel base (9) by each corner, be reminded there are 2 wheels with locks. Fix the wheels in place with
Lock Nut (8).
5.5. Put the Foam cushion (1) on the top. Hang the trays (7) on both side of the seat. Insert the drawer (4) into the drawer holder (3)
6. MAINTENANCE
6.1. Before each use, inspect the overall condition of the unit for broken, cracked or bent parts that may a󰀨ect the proper operation.
6.2. Regularly check the tightness of all fixings before use.
6.3. Smear the castor bearings with a thin film of silicone grease quarterly.
Refer to
instructions
SCR92 Issue 1 19/04/22
Original Language Version
© Jack Sealey Limited

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
SCR92 Issue 1 19/04/22
Original Language Version
© Jack Sealey Limited
Parts support is available for this product. Please email [e-mail] or telephone [phone]
6.4. Ensure the castor wheels are able to rotate and swivel freely. Replace if necessary.
6.5. Clean the seat cushion, trays and frames with a moist cloth and mild detergent. DO NOT use solvents to clean the unit.