Sealey SC02 User manual

INSTRUCTIONS FOR:
FLOOR CABINET 5 SHELF plus Clothes Hanger
MODEL No: SC02
1. SAFETY INSTRUCTIONS
2. INTRODUCTION
1.1 GENERAL SAFETY
 WARNING! Ensure Health & Safety, local authority, and
general workshop practice regulations are adhered to when
using this cabinet.
 WARNING! Use caution when handling and assembling
the metal components. The metal may have sharp edges
or corners, the use of protective gloves is recommended.
Locate cabinet in a suitable working area and secure to a
wall with suitable fasteners.
 Keep the work area clean and uncluttered.
Keep the cabinet clean and tidy in accordance with good
workshop practice.
Keep children and unauthorised persons away from the
working area.
 DO NOT climb, step or stand on the cabinet shelves.
 DO NOT use the cabinet for any purpose other than that
for which it is designed.
 DO NOT use in damp work areas.
 WARNING! The warnings, cautions and instructions
referred to in this instruction manual cannot cover all
possible conditions and situations that may occur. It must
be understood that common sense and caution are factors
which cannot be built into this product, but must be applied
by the operator.
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
3. CONTENTS
Original Language Version SC02 Issue:1 - 15/07/10
Use as an individual storage unit. Featuring two large
doors, four shelves and base storage. Added security
provided by cylinder lock, supplied with two keys. All steel
construction, stabilised by an inner cross member. Supplied
flat packed to save freight cost, simple assembly required.
Size (W x D x H): 916 x 458 x 1830mm
3.1 CONTENTS INSPECTION
Unpack all the parts and layout on the packing material. ....
A1 Back (left hand side).............................................1 off
A2 Back (right hand side)...........................................1 off
B1 Side (left hand side)..............................................1 off
B2 Side (right hand side)............................................1 off
C Cross member ......................................................1 off
D Base......................................................................1 off
E Base outer fascia..................................................1 off
F Top ........................................................................1 off
G Short Shelf............................................................3 off
H1 Door (left hand side).............................................1 off
H2 Door (right hand side)...........................................1 off
I Bolt and butterfly nut.............................................4 off
J Top panel retainer moulding .................................2 off
K Hinge pivot moulding ............................................4 off
L Locking rod recess moulding................................2 off
M Central divider.......................................................1 off
N Full width shelf......................................................1 off
O Coat rail fixing.......................................................2 off
P Coat rail.................................................................1 off
Q Door stop moulding...............................................4 off
R Hinge pin...............................................................4 off
S Shelf stop............................................................12 off

4. ASSEMBLY
4.5 TOP ASSEMBLY (Step 5)
4.5.1 Take the two top panel retainer mouldings (J) and fully
insert one into each hole at the top front edge of each
side panel in the orientation shown in Step 5.
4.5.2 Take the top panel (F) and hook it's front edge over the
two retainer mouldings, then swing the panel downwards
until the top edges of the back and side panels begin to
enter the receiving channels within the top panel. Tap the
top panel down into position using a rubber hammer until
the four indents in the back panels clip into the matching
holes in the back receiving channels.
4.4 BASE ASSEMBLY (Step 4)
4.4.1 Place the base (D) into position as shown above and
slide it down to the bottom until its edges make contact
with the receiving channels on the back and side panels.
Using a rubber hammer, tap the base down until it is fully
engaged in the channels.
4.3 CROSS MEMBER ASSEMBLY (Step 3)
4.3.1 Tie the side panels together at the bottom front edge by
attaching the cross member (C) using four bolts (I) and
 fourbutterynutsasshownintheinsetdiagramabove.
4.2 SIDE ASSEMBLY (Step 2)
4.2.1 Holdthesidepanels(B1&B2)ataslightangleandt
the tabs on the back panels into the slots of the side
panels and slide up to engage.
Original Language Version
4.1 BACK ASSEMBLY (Step 1)
4.1.1 Place the back panels (A1& A2) on a suitably protected
 atsurfacetopreventscratching.
4.1.2 Interlock the tabs into the slots on the back panels and
slide together until the two panels are fully engaged and
aligned.
SC02 Issue:1 - 15/07/10

4.8 SHELF ASSEMBLY (Step 7A)
4.8.1 Insert shelf stops (S) at the desired height for each shelf
and lay the shelves (G) onto the stops.
4.7 INTERNAL DIVIDERS ASSEMBLY (Step 7)
4.7.1 Manoeuvre the Full width shelf (N) into the top of the
cabinet, then move it downwards until the edges of the
shelf begin to enter the receiving channels on the inside
faces of the back and sides. Using a rubber hammer, tap
down the shelf until it is fully engaged.
4.7.2 Position the divider panel (M) inside the cabinet, just to
the right of the receiving channels on the base and on
the underside of the full width shelf (N). Move the divider
panel to the left until its edges begin to enter the
receiving channels. Using a rubber hammer, tap the
divider into place so that it is fully engaged.
4.7.3 Takethecoatrail(P)andpositionaxing(O)oneither
end. Slide the assembly into the right hand compartment
 ofthecabinetandslideeachxingdownintothe'U'
shaped channels provided.
4.6 BASE OUTER FASCIA ASSEMBLY (Step 6)
4.6.1 Fit the base outer fascia (E) over the cross member (C)
with the hinge pivot holes facing upwards. Tap the base
outer fascia down with a rubber hammer until the indents
in the sides of the fascia clip into the matching holes on
the cross member (C).
4.6.2 Insert a hinge pivot moulding (K) at each end of the
upper face of the base outer fascia (E). Insert the other
two hinge pivot mouldings at each end of the downward
facing edge of the cabinet top.
4.6.3 Insert a locking rod recess moulding (L) into the centrally
placed holes in the same faces used for mounting the
hinge pivot mouldings at both the top and the bottom.
Original Language Version SC02 Issue:1 - 15/07/10

4.9 DOORS ASSEMBLY (Step 8)
4.9.1 Mount each door in turn by placing it between the upper
and lower hinge pivot mouldings. Align the upper hole in
the door edge with the hole in the upper pivot moulding
and insert a hinge pin upwards through the door and into
the moulding. Rotate the short arm of the pin around onto
the inner face of the door as shown above and bend over
the metal tab to retain it. Mount the lower hinge pin in the
same way. Repeat the process to mount the other door.
4.9.2 Fit the rubber door stops (Q) as shown in Step 8 to the
corners of each door
4.10 Using a mild solution of detergent and water and wipe
the unit down with a soft cloth.
Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to
www.sealey.co.uk, email [e-mail] or phone [phone].
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
[e-mail]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
Original Language Version SC02 Issue:1 - 15/07/10