Sealey HT02LED User manual

2W & 1.5W SMD LED RECHARGEABLE CLIP
LIGHT WITH AUTO SENSOR
MODEL NO: HT02LED
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. GENERAL
8DO NOT shine directly into your, another person’s or an animal’s eyes.
8DO NOT allow children to use the torch.
8DO NOT use the torch if you suspect that the battery or the torch casing is damaged.
1.2. BATTERY SAFETY
WARNING! To reduce the risk of burns or re:
8DO NOT attempt to open, disassemble, modify or service the batteries.
8DO NOT crush, puncture, short contacts or dispose of in re or water.
8DO NOT expose to temperatures above 60°C (140°F).
2. INTRODUCTION
200/150 Lumen clip light with auto-sensor built-in. Light is designed to be clipped to the supplied headband or to a cap. Features front
directional torch and top spotlight with four settings including red light setting. Light easily ips up so you can alternate between lights quickly.
Clip also features two magnets on the bottom enabling it to be used independently as a work light. Battery type: 3.7V Lithium-Polymer.
Supplied with USB charging cable.
3. SPECIFICATION
Model No:....................................................... HT02LED
Battery: .............................................3.7V 0.5Ah Li-Poly
Charging time..................................................1.5 Hours
Lumen Output: .............................................. 200/150lm
Operating time .................................................2hr-12hr
4. OPERATION
HT02LED Issue 4 (4) 12/05/23
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Spot light
Flood light
(Back)
cap clip/ headband clip/
magnets
Sensor receiver spotlight
On/Off
Switch and motion sensor switch
Charging port: Red/green
indicates charging status.
Flashes green when motion
sensor is activated.

4.1. WORK MODES:
4.1.1. LED Floodlight Low Press on/o󰀨 switch once and the low oodlight will illuminate.
4.1.2. LED Floodlight High Press a second time and the high oodlight will illuminate
4.1.3. LED Floodlight Red Press a third time and the Red light will illuminate.
4.1.4. LED Spotlight Press a forth time and the spotlight will Illuminate.
4.1.5. One further press will turn the light o󰀨.
4.1.6. Sensor mode, press the sensor switch, wave the hand at the sensor reception to enter the sensor mode.
Green light will ash near charging point to show it is operational. This will operate in any work mode listed above.
4.2. RECHARGING
4.2.1. Designed with USB Type C input, supplied with a USB cable which allows for quick and convenient charging.
4.2.2. Red indicator strobes when charging green indicator stays on after fully charged.
5. MAINTENANCE
5.1. Keep the torch clean by wiping with a damp cloth.
5.2. Store torch in a dry childproof area.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste.All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product
becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and
dispose of the product and fluids according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Original Language Version
© Jack Sealey Limited
BATTERY REMOVAL
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack
Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.
REGISTER YOUR
PURCHASE HERE
HT02LED Issue 4 (4) 12/05/23