Sealey MS162 User manual

INSTRUCTIONS FOR
MOTORCYCLE BRAKE PISTON REMOVAL KIT-
14PC
MODEL NO: MS162
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
I
MPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGEAND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Wear appropriate Personal Protective Equipment. A full range of Personal Protective Equipment is available from your
Sealey dealer.
WARNING! Ensure that Health & Safety, Local Authority Regulations and general workshop practice Regulations are adhered to when
using tools.
8DO NOT use tools if damaged.
9Maintain tools to ensure that they are in an adequate condition for safe use and optimum performance.
9Ensure that a vehicle that has been raised by a jack is adequately supported.
9Wear suitable clothing to avoid snagging.
8DO NOT wear jewellery. Tie back long hair.
9Account for all tools, parts and components being used.
8DO NOT leave tools in or near the engine. Return tools to suitable storage after use.
9When not in use, store in a safe dry and childproof place.
9Keep children and unauthorised persons away from the work area.
2. INTRODUCTION
Extract brake calliper pistons without risk of damage to outer face of piston. Fast and simple operation. Features detachable slide hammer for
impact removal. The kit includes 12 adaptors to suit different sized pistons.
3. SPECIFICATION
Model No.....................................................................MS162
Capacity...............................................................Ø19-30mm
4. OPERATION
4.1.  Selectcorrectsizeadaptorforthejobrequirements.(g.1.1).
4.2.  Clampbrakecalibreinsoftjawvice(g.2).
4.3.  Removeinnerspindlebyunscrewingfrommainbodyoftool(g.1.2).Slideadaptorontospindleslottedendrst,reassemble
tool.
4.4. Slide adaptor into Brake piston and tighten to clamp the adaptor inside the piston.
4.5.  Screwslidehammertoendoftool(g2).
4.6.  Withcareusetheslidehammerforimpactremovaltopullthepistonfromthehousing(g3).
4.7. Remove tool from piston in reverse order to above.
MS162 | Issue 1 17/05/16
Original Language Version
© Jack Sealey Limited
Wear
Protective
Gloves
Refer to
Instruction
Manual
Wear eye
Protection
2
3
1
Fig 1.

5. MAINTENANCE
5.1. Keep the tools clean and store in the case provided.
5.2. Store in a dry, childproof area.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specications and component parts without prior notice.
IMPORTANT:No liability is accepted for incorrect use of this product.
WARRANTY:Guarantee is 12 months from purchase date, proof of which will be required for any claim.
Sole UK Distributor, Sealey Group.
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk.
IP32 7AR
www.sealey.co.uk
[e-mail]
01284 757500
01284 703534
Web
MS162 | Issue 1 17/05/16
Original Language Version
© Jack Sealey Limited
Fig 2. Fig 3.
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email [e-mail] or telephone [phone].
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.