Sealey MS070.V2 User manual

MOTORCYCLE WHEEL ALIGNMENT TOOL
MODEL NO: MS070.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
equipment.
9Maintain the wheel alignment tool in good condition.
9Replace or repair damaged parts. Use genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
9Locate wheel alignment tool in a suitable working area, keep area clean and tidy and free from unrelated materials.
WARNING! Ensure that the motorcycle is on a stable stand located on level and solid ground.
9Keep the gauge scales clean to ensure accurate performance.
8DO NOT use outside in damp or wet weather conditions.
8DO NOT allow untrained persons to operate the aligner.
WARNING! The warnings, cautions and instructions contained within this document cannot cover all possible conditions and
situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product,
but must be applied by the operator.
9Any alignment changes deemed necessary as a result of using this equipment must be made strictly in accordance with the
motorcycle manufacturer’s recommendations.
▲Laser Safety
The MS070 utilises a Class 2M laser that emits low levels of visible radiation light (i.e. wavelengths between 630 and 640 nanometres)
which are safe for the skin but not inherently safe for the eyes. The Class 2M emission limit is set at the maximum level for which eye
protection is normally afforded by natural aversion responses to bright light. Accidental eye exposure is therefore normally safe,
  althoughthenaturalaversionresponsecanbeoverriddenbydeliberatelystaringintothebeam,andcanalsobeinuencedbytheuse
of alcohol or drugs.
WARNING! DO NOT look or stare into the laser beam as permanent eye damage could result.
8DO NOT direct the laser beam at any person’s (or animal’s) eyes as eye damage could result. If the beam is obstructed by a person
during use, release the contact switch immediately.
8DO NOTusetheequipmentwhileundertheinuenceofalcohol,drugsorwhilstonmedication.
9 Beawarethatreectionsofthelaserbeamfrommirrorsorothershinysurfacescanbeashazardousasdirecteyeexposure.
2. INTRODUCTION
Fast,simpleandaccuratealignmentofrearwheel.Optimisesvehicleperformanceandsetupafterinstallationormodicationofthechain,
sprockets, brakes or suspension components. This fully portable kit is also ideal for track-day set up or for the motorcycle enthusiast.
MS070.V2 Issue 2 (H4F) 25/05/18
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Warning
Laser beam

3. PREPARATION
ADAPTOR BLOCKS
3.1.  TheMS070includesadaptors(g1).
3.2. Use the adaptors to ensure that the MS070 is set up accurately.
3.3. Place the adaptor blocks against each side of the wheel rim(g2).
4. SET UP
4.1. Laser Power: ThelaserunitsarebatterypoweredandrequiretwoAAbatteriesineachbatterybox.Seeg.4.
4.2. Slide back the lid on each box and insert the batteries paying attention to the polarity markings in the base of each box. Slide the
lids back into position on each battery box.
4.3. Ensure the laser units are working by switching on with the units directed to the ground. Switch off after testing.
4.4. Assembly: Identify the laser unit with the threaded insert in the side and screw one of the threaded rods supplied into the insert.
Identify the scale unit with the threaded insert in the side and screw the other threaded rod into place.
4.5. Motorcycle stability: Before attaching the laser and scale units you must ensure that the motorcycle is adequately supported on a
suitable stand that lifts the rear wheel from the ground and supports the motorcycle in a perpendicular orientation. The stand must
 alsobeonarmstablesurfacesuchasconcrete.
4.6. Attaching the laser units to the rear wheel:Referringtog.3,loosentheclampandremovetheclampunitandspringfromthe
rod together with the right hand laser unit. Position the left hand laser unit with the rod attached on the nearside of the
rear wheel and insert the rod through the adaptor and then through the lower part of the wheel. Slide the right hand adaptor and
laser unit onto the rod and up to the tyre, followed by the spring and clamp unit. Clamp the two units lightly to the wheel using the
adaptors on the wheel rim to space the laser unit away from the tyre in the position indicateding.4.
Key
1. Left Laser Unit
2. Right Laser Unit
3. Threaded Rod
4. Clamp and Spring
5.Threaded Bush
6. Adaptors
7. On/Off Switch and Light
8. Battery Box
9. Calibration Shield
g.1
g.2
g.3 g.4
MS070.V2 Issue 2 (H4F) 25/05/18
Original Language Version
© Jack Sealey Limited

4.7. Attaching the scale units to the front wheel:Referringtog.5,loosentheclampandremovetheclampunitandspringfromthe
rod together with the right hand scale unit. Position the left hand scale unit with the rod attached on the nearside of the front wheel
in a near vertical orientation and insert the rod through the adaptor and then through the front part of the wheel. Slide the right hand
adaptor and scale unit onto the rod and up to the tyre, followed by the spring and clamp the two units lightly to the wheel using the
 adaptorsonthewheelrimtospacethelaserunitawayfromthetyreinthepositionindicateding.6.
4.8. Switch on the lasers and note the position of each beam on the scales. If necessary, adjust the position/angle of the laser units on
the rear wheel to get the beams to appear on the scales.
4.9. Front wheel position: The front wheel must be in the straight ahead position before accurate alignment can take place. If the beams
are parallel with the scale lines the front wheel is set dead ahead. If the beams are at an angle to the scale lines, turn the wheel
one way or the other until they are parallel.
4.10. ALIGNMENT PROCEDURE
4.11. Compare the readings on the scales. If they are the same then the rear wheel is in alignment with the front wheel. If they are not
the same then it will be necessary to operate the rear wheel adjusters. If the reading is higher on the right hand scale, tighten the
left hand adjuster. If the reading is higher on the left hand scale, tighten the right hand adjuster. When the wheels are in alignment,
nallytightentherearwheelaxlexings.
g.5
g.6
g.7
MS070.V2 Issue 2 (H4F) 25/05/18
Original Language Version
© Jack Sealey Limited

MS070.V2 Issue 2 (H4F) 25/05/18
Original Language Version
© Jack Sealey Limited
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
BATTERY REMOVAL SEE SECTION 4
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack
Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.