Sealey AK36D.V2 User manual

36LTR/ 80LTR MOBILE OIL DRAINER MANUAL
DISCHARGE
MODEL NO: AK36D.V2 & AK80D.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general
workshop practice regulations are adhered to when using this equipment.
9Familiarise yourself with the application, limitations and hazards of the oil
drainer.
9Maintain the drainer in good condition (use an authorised service agent).
9Replace or repair damaged parts. Use genuine parts only. Unauthorised
parts may be dangerous and will invalidate the warranty.
9Keep the work area clean, uncluttered and ensure there is adequate
lighting.
9Keep the drainer clean for best and safest performance.
9Maintain correct balance and footing. Ensure the floor is not slippery
and wear non-slip shoes.
9Keep children and unauthorised persons away from the work area.
8DO NOT use the drainer for any purpose other than that for which it
is designed.
8DO NOT operate the drainer if any parts are damaged or missing as
this may cause failure and/or personal injury.
8DO NOT stand on the drainer.
8DO NOT allow untrained persons to operate the drainer.
8DO NOT operate the drainer when you are tired or under the influence
of alcohol, drugs or intoxicating medication.
9When not in use, store in a safe, dry, childproof area.
9Dispose of waste oil in accordance with local authority regulations.
2. INTRODUCTION
Polyethylene reservoir, 36/80ltr capacity, mounted on four castors for mobility.
Drain pan, with filter, on height adjustable down tube. Hand grips for emptying
(AK36D.V2): rotary pump or gravity drain tap for emptying (AK80D.V2)
3. SPECIFICATION
Model No:............................................................. AK36D.V2 .............................................................................. AK80D.V2
Air Discharge: ................................................................... No ...........................................................................................No
Capacity:......................................................................... 36ltr ........................................................................................ 80ltr
Collection Bowl Capacity (ltr): .........................................15ltr ........................................................................................ 15ltr
Gravity Discharge: ............................................................ No ..........................................................................................Yes
Gravity Feed: ................................................................... Yes ..........................................................................................Yes
Manual Discharge: ........................................................... Yes ..........................................................................................Yes
Maximum Height to Pan:.......................................... 1600mm ..................................................................................1800mm
Minimum Height to Pan:............................................. 760mm ....................................................................................940mm
Model No: ...................................................................AK36D .................................................................................... AK80D
Pump Discharge: .............................................................. No ...........................................................................................No
Suction Probe: .................................................................. No ...........................................................................................No
Temperature Range: .................................................... <80°C ..................................................................................... <80°C
4. ASSEMBLY
4.1. Insert the lower tube through lower tube clamp and secure by tightening the clamp.
4.2. Place the tool tray over the lower tube.
4.3. Insert the upper tube into the lower tube.
4.4. Slide the upper tube retaining clip down the upper tube (press the two ends together to release the grip) until the clip rests on the lower
tube at the required level.
4.5. Place the drain pan on top of the upper tube.
g.1
AK36D.V2 AK80D.V2 Issue 1 (3) 10/06/19
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear protective
clothing

5. OPERATION
5.1. Place mobile oil drainer under the equipment to be drained. Raise the drain pan beneath the equipment’s drain valve or vent.
5.2. When draining is complete, lower the drain pan before removing the drainer.
5.3. EMPTYING OIL DRAINER (AK36D.V2)
5.3.1. Disconnect the drain pan and release the tubes from the reservoir. Remove the cap from the drain port.
5.3.2. Using the hand grips, tip the reservoir to dispose of the waste oil into a suitable container.
5.4. EMPTYING OIL DRAINER (AK80D.V2) BY GRAVITY.
5.4.1. Connect a drain hose to the drain tap.
5.4.2. Empty the reservoir by opening the drain tap and draining by gravity to a lower level tank.
5.5. EMPTYING OIL DRAINER (AK80D.V2) BY PUMP.
5.5.1. Remove the drain port cover and install the pump using the 2” BSP adaptor (fig.2). Ensure that the pick-up tube reaches the bottom of
the reservoir.
5.5.2. Fit a suitable hose to the pump outlet and connect to the waste oil tank. Pump out as necessary.
6. MAINTENANCE
6.1. Clean the drain pan filter frequently; a blocked filter can cause the drain pan to overflow.
6.2. Clean the exterior of the unit regularly with paper towel or cleaning cloth.
AK80D.V2 shown with TP55 pump (not
supplied) fitted into drain port.
g.2
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on [e-mail] or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
AK36D.V2 AK80D.V2 Issue 1 (3) 10/06/19
Original Language Version
© Jack Sealey Limited