Sealey VS0275 User manual
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9Keep children and unauthorised persons away from the work area.
9Keep work area clean and tidy and free from unrelated materials.
9Ensure the work area has adequate lighting.
8DO NOT touch the probe whilst switched on, it will be hot.
8DO NOT use the tester to perform a task for which it is not designed.
8DO NOT allow untrained persons to use the tester.
8DO NOT
9After use, clean equipment and store in a cool, dry, childproof area.
1.1. BRAKE FLUID SAFETY
9
9
9
WARNING!
WARNING!
1.2. PERSONAL PRECAUTIONS (WORKING WITH BATTERIES)
9Ensure there is another person within hearing range, or close enough to come to your aid should a problem arise, when working near a
9
9
9Wash immediately with soap and water if battery acid contacts skin or clothing. If acid enters eye, flush eye immediately with cool, clean
running water for at least 15 minutes and seek immediate medical attention.
9
2. INTRODUCTION
T
way to detect this small water content is to measure the boiling point of the fluid. The unit incorporates a heater element.
3. CONTENTS
BRAKE FLUID BOIL TEST
VS0275
Refer to
Instruction
Manual
Wear eye
Protection
Wear
P
G
W
Hot
urface
Original Language Version
V
4. OPERATION
DO NOT
connectors immediately.
CLEANING
heater, wash it with clean water and wipe dry. DO NOT immerse
Wipe and dry the test container and syringe,
replace both carefully in the case.
TESTING
IMPORTANT:
the indicator light will be red.
round.
PREPARING BRAKE FLUID
container.
Put the heater into the test container.
DO NOT
green.
The indicator light will be yellow when the test is complete. To start the test again, wait until the light turns red.
Fig.2
Fig.3
Fig.4
Original Language Version
V
9 8
Fig.5
ABNORMAL OPERATION DISPLAYS
IMPORTANT:
use the tester again.
CALIBRATION TEST
using clean water.
If the tester is working correctly the result will be
INSPECTION STANDARD VALUE
manufacturer.
Fig.6
Fig.7 Fig.8
Fig.9
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk
Note
notice.
Important
Warranty
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
according to local regulations.
WEEE REGULATIONS
waste authority for recycling information.
Original Language Version
V
Table of contents
Other Sealey Test Equipment manuals
Sealey
Sealey BT2003.V4 User manual
Sealey
Sealey GT117 User manual
Sealey
Sealey TST22 User manual
Sealey
Sealey BT2013.V4 User manual
Sealey
Sealey BT2011 User manual
Sealey
Sealey CV0011 User manual
Sealey
Sealey CT955 V3 User manual
Sealey
Sealey AUTO SERVICE LINE TA125 User manual
Sealey
Sealey BT2003.V5 User manual
Sealey
Sealey BT2101 User manual
Sealey
Sealey VS2058.V2 User manual
Sealey
Sealey BT01 User manual
Sealey
Sealey AUTO SERVICE VSE206 User manual
Sealey
Sealey Auto Service BT91D.V2 User manual
Sealey
Sealey VS001.V3 User manual
Sealey
Sealey TST22 User manual
Sealey
Sealey CT955.V4 User manual
Sealey
Sealey VSE2020.V2 User manual
Sealey
Sealey BT91/7P User manual
Sealey
Sealey TA126 User manual
