Sealey VS0220 User manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
VS0220 Issue 2 (2,3) 22/03/23
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Wear eye
protection
PREMIER 1.2L PNEUMATIC VACUUM BRAKE &
CLUTCH BLEEDER
MODEL NO: VS0220
1. SAFETY
9Familiarise yourself with the applications and limitations, as well as any potential hazards, of the kit.
9Keep this product in good working order and condition. (take immediate action to repair or replace damaged parts).
9Use approved parts only (unapproved parts may be dangerous and will invalidate the warranty).
9Keep children and unauthorised persons away from the work area.
9Keep work area clean and tidy and free from unrelated materials.
9Ensure the work area has adequate lighting.
8DO NOT use the kit to perform a task for which it is not designed.
8DO NOT allow untrained persons to use the kit.
8DO NOT use whilst under the inuence of drugs, alcohol or intoxicating medication.
9After use, clean equipment and store in a cool, dry, childproof area.
9Dispose of waste liquids in accordance with local authority regulations.
9 Always read and comply with the warnings on the brake uid container.
9 Wear eye protection and keep skin contact to a minimum. If brake uid enters eyes, rinse with plenty of water and seek medical
advice. If swallowed seek medical advice immediately.
WARNING! Brake uid is ammable - keep away from sources of ignition, including hot surfaces e.g. exhaust manifold.
WARNING! Brake uid will damage paintwork. Any spillage should be ushed with water immediately.
9After use, clean equipment and store in a cool, dry, childproof area.
2. INTRODUCTION
One-person operation using standard workshop air supply (87-174psi/6-12bar). With a flexible hanging hook. Durable hard-wearing Acetal plastic.
Trigger for adjusting air pressure, with an added trigger lock. Draws fluid from the bleeding nipple enabling either bleeding or full replacement of
fluid in the system. Clear PVC hose easily checks for air bubbles. Hose length 1.5m. Does not require specialised brake reservoir caps.
3. SPECIFICATION
Model No:................................................................. VS0220
Air Consumption: .................................................... 180L/min
Inlet Size:..................................................................1/4”BSP
Maximum Air Supply: ........................................ 174psi/12bar
Tank Capacity: ................................................................1.2L
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURYAND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

4. OPERATION
Numbers refer to diagram below.
4.1. With this brake bleeder, one person can carry out the bleeding of the brake systems. Bleeding is completed quickly, cleanly and simply.
Brake fluid is sucked into the container avoiding unnecessary spillages.
4.2. Connect the gun to the compressed air line system (1).
4.3. Set the brake bleeder’s rubber pipe on the bleed screw, and loosen the bleed screw (2).
4.4. Activate the handle of the brake bleeder, a partial vacuum is created in the brake bleeder container, and the fluid is sucked into the
container (3).
4.5. When the brake fluid is free of air bubbles, which can be seen through the clear hose (4), then tighten the bleed screw and remove the
rubber pipe.
4.6. Repeat the procedure for each brake calliper.
4.7. REMEMBER to check brake fluid level in reservoir
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 [e-mail] www.sealey.co.uk
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste.All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product
becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and
dispose of the product and fluids according to local regulations.
Original Language Version
© Jack Sealey Limited
REGISTER YOUR
PURCHASE HERE
VS0220 Issue 2 (2,3) 22/03/23