Sealite SL-15 User manual

sealite.com
SL-15_BLE_QSG_EN_V2.2
Thank you for purchasing
the SL-15
This guide will provide you
with a brief summary of the
steps involved in successfully
installing the SL-15 compact
marine lantern.
Your system will consist of:
1 x SL-15 marine lantern and switch key
Other tools required to successfully set up this
product, are:
• Internet connection
• SealitePro for Bluetooth®Connectivity
Introduction
The purpose of this quick start guide is to present a
brief summary of the steps involved in the installation
of the SL-15 compact marine lantern, from the
physical installation of the product itself to the
conguration of its Flash Code.
Quickstart
1. Remove the SL-15 Lantern from the packaging.
2. Check if Lantern is switched ON
(Using steps below)
3. The SL-15 is set to a Flash Code of:
0.3 seconds ON; and
2.7 seconds OFF
(Switch Position ‘A’ in Flash Code Table)
4. If the SL-15 lantern is preset to the ON
position it is currently in Sleep Mode.
5. To activate, expose the lantern to
30 seconds of sunlight.
6. To check lantern is working, cover the lantern in
darkness for at least 30 seconds.
7. If you wish to alter the Flash Code please follow the
steps over the page (Adjusting the Flash Code),
otherwise proceed to install your lantern.
8. Position the lantern in your desired location
and secure, utilising the 4 x holes in the ange.
Ensure the lantern is bolted to an even, at surface.
Link to SL-15 Product Page
To access more information go to the
SL-15 product page on the Sealite
website: http://www.sealite.com/products/
marine-lanterns/1-2nm-solar-marine-lantern
Download Installation
Manual
Scan the QR Code to download the
SL-15 Installation Manual from the
Sealite website.
Charging the Battery
New lanterns should be left in the sun for 1-2 days to
ensure battery is charged before placing in service.
Please note, lantern will re-charge even when switch
is turned to ‘OFF’ position.
Preferred Installation Location
For best lantern performance, ensure solar modules
are not covered and are in clear view of the sky
with no shadows.
Solar Marine Lantern
1 - 2NM+
Quick Start Guide
SL-15

sealite.com Head Oce
[phone]
Americas
[phone]
UK
[phone]
Asia
[phone]
SL-15_BLE_QSG_EN_V2.2
Turning the Lantern ON
and Adjusting the Flash Code
1. Remove the 4 x battery cover screws and lift the cover and battery out
of the compartment to expose the adjustment plug.
2. Unscrew the adjustment plug.
3. Ensure internal lantern switch is set in the ON position.
4a. For Non Bluetooth users: Using a small at bladed screwdriver adjust
the Flash Code to the desired setting. (Refer Flash Code Table)
4b. For Bluetooth®Users: Connecting to the SealitePro®App
Download the SealitePro®App to your device. It is available for both
Android®and iOS platforms. Open the App on your device and connect
to the lantern, by pressing “Connect via Bluetooth®”. Select a lantern
displayed on the “Scan for Lanterns” screen. Expand the “Lantern
Information” drop downmenu then press Identify. The lantern will ash
quickly several times as conrmation.
Note: only one device may be connected at any onetime.
5. Cover the lantern, in darkness, for at least 30 seconds to activate the
lantern sensor. Make sure the lantern is ashing correctly.
6. Uncover the lantern and wait at least 30 seconds to make sure the
lantern turns o in daylight.
7. Insert the adjustment plug and replace the battery.
8. Replace the cover and secure using the 4 x screws.
Do Not over tighten screws.
Flash Code Table
+-
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
Battery Cover
Battery Position
Battery Terminals
Adjustment Plug
(Removed)
Lantern Underside
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
OFF ON
Flash Code
Adjustment Switches
Switch Position Flash Setting Duty Cycle
(%)
On (sec) O (sec)
0Steady On 100
10.5 1.0 33
20.5 3.5 12.5
31.0 3.0 25
40.5 5.5 8.5
50.3 0.7 30
60.3 (On), 0.7 (O), 0.3, 0.7, 0.3, 0.7, 0.3, 15.7 6.5
70.3 1.7 15
80.3 2.2 12
90.5 2.0 20
A0.3 2.7 10
B0.5 2.5 16.5
C0.7 2.3 23.5
D0.5 4.5 10
E1.0 4.0 20
FCustom Flash Code Position - (on request)
Solar Marine Lantern
1 - 2NM+
Quick Start Guide
SL-15