Seat Charger User manual

SEAT Charger
Manual – Part A.
EN PLES EL
Powered by

English.

Contents.
General information and scope.
Scope of the document 06
General 06
Safety precautions 07
Technical specifications 10
Product information.
Product information 12
Charge with the wallbox.
Start and stop a charging session 15
Status indication 16
Prepare for installation.
Content of delivery 20
Prerequisites for installation 21
Tools and material needed 23
Notice on installation 25
Install wallbox.
Install wall bracket 28
Prepare main assembly for installation 28
Mount main assembly onto wall bracket 29
Assemble wallbox 30
Set DIP-switches.
Set DIP-switches 33
Configure SEAT Charger Connect
and SEAT Charger Pro.
Privacy information 40
Configure the SEAT Charger Connect
and SEAT Charger Pro locally 43
Pair SEAT Charger Connect
and SEAT Charger Pro to App account 44
Commissioning.
Commissioning 45
Maintenance.
Maintenance 45
Troubleshooting.
Error states of the wallbox 46
Adjust the length of the charging cable 51
Decommissioning.
Decommissioning 52
Disposal.
Disposal 53
Appendix.
Warranty 54
EU Declaration of conformity 54
Glossary 55
4

5
English

General information
and scope.
Keep this manual for the entire life cycle
of the product.
The following installation-related and
troubleshooting chapters are intended for
qualified personnel, such as certified
electricians, who can correctly and safely
install the wallbox and identify potential
danger:
• Chapters: 1, 4, 5, 6, 8, 9, 10, 11 and 12.
The following usage-related chapters are
intended for end-users to correctly and safely
operate the wallbox:
• Chapters: 1, 2, 3, 7 and 13.
Legal information.
© 2020 EVBox Manufacturing B.V. - all rights
reserved. Nothing from this document may be
modified, reproduced, processed, or
distributed in any form or by any means,
without the prior written permission of EVBox.
Scope of the document.
The charging station has been CE-certified by the manufacturer
and bears the CE logo. The relevant declaration of conformity may
be obtained from the manufacturer.
The charging station complies with the RoHS Directive (RL //EU).
The relevant declaration of conformity may be obtained from
the manufacturer.
Electrical and electronic appliances, including accessories, must
be disposed of separately from the general municipal solid waste.
Recycling of materials saves raw materials and energy and makes
a major contribution to conserving the environment.
General.
Product and environmental characteristics.
6

Highlighted sections.
Danger.
Texts with this symbol
contain information regarding
hazardous situations which
will cause death or severe
injures if ignored. Warning.
Texts with this symbol
contain information regarding
hazardous situations which
could cause death or severe
injuries if ignored. Caution.
Texts with this symbol contain
information regarding
hazardous situations which
could cause minor or
moderate injuries if ignored.
Safety precautions.
Read and obey the following safety precautions before you install, service or use your charging
station. A qualified electrician must ensure that the charging station is installed in accordance
with the relevant country-specific standards and local regulations.
Symbols.
The symbols used in this manual have the following meaning:
Symbols used and their explanations.
B 5.1 This symbol indicates that the illustrations corresponding to the indicated
chapter are to be found in manual B.
1., a. or I. Actions to be followed in the stated order.
• Actions to be followed in a non-specific order.
Note: Texts with this symbol contain supplementary information.
7
English

The following sections contain general information that applies when installing
and using the wallbox.
Danger.
Operating the wallbox when it indicates
an error state, or when the wallbox or the
charging cable have cracks, show extensive
wear, or other physical damage, will result
in the risk of electric shock, which will cause
severe injuries or death.
• Do not operate the wallbox if it is physically
damaged.
• In the event of danger and/or an accident,
a certified electrician must immediately
disconnect the electrical supply from the
wallbox.
• See chapterTroubleshooting for
explanation and further instructions
on indicated error states.
• Contact cupr[email protected]o
or your distributor if you suspect that the
wallbox or cable is damaged.
Some electric vehicles release hazardous or
explosive gasses when charging which will
result in the risk of explosion, and thus cause
severe injuries or death.
• Refer to your vehicle user manual to
check if your vehicle releases hazardous
or explosive gases when charging.
• Follow the instructions given in the vehicle
user manual before choosing the location
of the charging station.
Extensive exposure of the wallbox to water or
handling the wallbox with wet hands will result
in the risk of electric shock, which will cause
severe injuries or death.
• Do not direct powerful jets of water toward
or onto the wallbox.
• Never operate the wallbox with wet hands.
• Do not put the charging plug into any liquid.
Not following the installation instructions given
in this manual will result in the risk of electric
shock to users, which will cause severe injuries
or death.
• Read this manual before installing
the wallbox.
• If you are unsure about how to use the
wallbox after reading this manual, ask for
help at cupra-seat[email protected]o or visit
your local dealer for more information.
• Do not allow children to operate the wallbox.
Adult supervision is required when children
are near a wallbox that is in use.
Servicing of the wallbox or its components by
non-qualified personnel will result in the risk
of electric shock and damage to the wallbox,
which will cause severe injury or death.
• The user must not attempt to service or
repair the wallbox as it does not contain
user-serviceable parts.
• The wallbox must only be serviced, repaired
or relocated by a qualified electrician.
8

Caution.
Charging the electric vehicle with the charging
cable not being completely unwound may result
in overheating of the cable, which can damage
the wallbox.
• Make sure to completely unwind the charging
cable and avoid overlapping loops before
charging your electric vehicle.
Putting fingers into or leaving other objects
inside the plug port (for example during
cleaning) may cause injury or damage to
the wallbox.
• Do not put your fingers into the plug port.
• Do not leave objects inside the plug port.
Use of devices with (electro) magnetic properties
in the vicinity of the wallbox may cause damage
to the wallbox and aect its operation.
• Keep and use (electro) magnetic devices
a safe distance from the wallbox.
Transport and storage.
• Disconnect input power before removing the
charging station for storage or relocation.
• Only transport and store the charging station
in its original packaging. No liability can be
accepted for damage incurred when the
product is not transported in its original
packaging.
• Store the charging station in a dry
environment in the temperature range
given in the specifications.
Warning.
Improper usage of the wallbox may result in
damage to the wallbox, which may cause injury
or death.
• Read this manual before using the wallbox.
• If you are unsure about how to use the wallbox
after reading this manual, ask for help at
cupra-seat[email protected]o or visit your
local dealer for more information.
• Do not allow children to operate the wallbox.
Adult supervision is required when children
are near a wallbox that is in use.
Using adapters, conversion adapters or cord
extensions with the wallbox may result in
technical incompatibilities and can result in
damage to the wallbox, and thus cause injuries
or death.
• Use this charging station to charge Mode
 compatible electric vehicles only.
• Refer to your vehicle user manual to check
if your vehicle is compatible.
Exposure of the wallbox to heat sources or
flammable substances can result in damage
to the wallbox, and thus cause injuries or death.
• Make sure that the wallbox or the charging
cable never come into direct contact with
heat sources.
• Do not use explosive or readily flammable
substances near the wallbox.
Using the wallbox under conditions not
specified in this manual may result in damage
to the wallbox, which may cause injury or death.
• Only use the wallbox under the specified
operating conditions, see chapterTechnical
specifications.
9
English

Technical specifications.
Electrical properties
Connection capacity 1-phase, 230 V, 32 A, 50 Hz 3-phase, 400 V, 16 A, 50 Hz
Charging capacity 7.4 kW (1-phase - 32 A) 11 kW (3-phase - 16 A)
Charge mode Mode 3 (IEC 61851) - ISO 15118*
Fixed charging cable Type 2 plug (IEC 62196-2)
Number of fixed
charging cables
1
Charging cable length 4.5 m or 7.5 m
Installation wiring 16 A installation input
terminals: 1 - 6 mm
32 A installation input
terminals: 1 - 10 mm
Metering Optional, for SEAT Charger Pro.
Safety and certification
Upstream installation
protection
Minimum dedicated 1-phase 32 A (32 A station) or 3-phase 16 A
(16 A station) upstream circuit breaker and at minimum RCD type A
(30 mA AC). Check local installation requirements if additional
measures are required
Static power limitation Via DIP-switches
Earth leakage sensor
(ELS)
6 mA DC
Ground loss monitor Physical connection m quality onitoring, without ground monitoring
Via CT coils - optional comfort feature
Invasive / non-Invasive - 40 A - 200 A,brands: VAC, LEM, and Nidec.
See chapter Set DIP-switches for the supported models
Operating temperature
range
-30 °C - +50 °C
Storage temperature
range
-30 °C - +85 °C
Operating humidity Max. 95 % - non-condensing
Maximum installation
height
Max. 4000 m above sea level
Enclosure ratings IP54 (IEC 60529), IK10 (IEC 62262)
Certification See EU Declaration of conformity
Safety Class Safety Class I (the charging station is equipped with a ground terminal
for safety) and overvoltage Category III
Power supply input EV Supply equipment permanently connected to AC supply network
Normal Environmental
conditions
Outdoor use
Access Equipment for locations with non-restricted access
10

*For SEAT Charger Connect and SEAT Charger Pro only.
Connectivity
Authorization* NFC / RFID (ISO 14443, ISO 15693) Plug & Charge (ISO 15118)
Status indication /
HMI (Human Machine
Interface)
LED based HMI
Communication
standard*
Wi-Fi 2.4 / 5 GHz, Ethernet (via RJ45 connection), optional 4G / LTE
Communication
protocol to backend*
OCPP 2.0J
Communication
protocol to Home Energy
Management System*
EEBus
Local configuration* via Configuration Manager
Physical properties
Housing Polycarbonate
Front panel Polycarbonate and hardened glass
Bezel Acrylonitrile Styrene Acrylate (ASA)
Mounting bracket Steel (zinc plated)
Dimensions (W × H × D) 297 mm × 406 mm × 116 mm
Weight 1-phase 32 A
station with
4.5 m charging
cable ~ 6 kg
1-phase 32 A
station with
7.5 m charging
cable ~7 kg
3-phase 16 A
station with
4.5 m charging
cable ~ 6 kg
3-phase 16 A
station with
7.5 m charging
cable ~ 7 kg
Mounting method Stationary equipment, mounted on walls (preferred method),
poles or equivalent positions – surface mounted
Color Platinum gray with electric white bezel
11
English

Product information.
Features SEAT
Charger
SEAT Charger
Connect
SEAT
Charger Pro
Maximum output power
7.4 kW (1-phase)
Maximum output power
11 kW (3-phase)
Attached charging cable
Type 2 (4.5 m or 7.5 m)
Alternating Current (AC)
charging
Integrated Direct Current
(DC) fault current detection
Wi-Fi / Ethernet
communication −
LTE mobile network
communication −*
Data transfer according
to OCPP 2.0J −
Access control
with charge card −
Remote access via SEAT Easy
Charging App −
Remote software update /
diagnostic −
MID certified power
consumption recording
and calculation
− −
*Option.
The table below contains the available product configurations
for the SEAT Charger models.
12

13
English

Charge with
the wallbox.
Warning.
Using a damaged wallbox or a damaged charging cable may expose the user to electric
components and result in the risk of electric shock, which may cause injury or death.
• Always check that thewallbox, the charging
cable, and the charging plug are free of
damage before starting a charging session.
•Always check that the contact area of the
charging plug is free from dirt and moisture
before starting a charging session.
• Make sure that the charging cable
cannot become damaged (kinked,
jammed or driven over).
•Take precautions so that the charge
plug does not come into contact with
heat sources, dirt or water.
14

Start and stop a charging session.
Start charging.
Your car is charging.
Plug the charging cable into
your car.
Optionally, holdyour charge card
(RFID card) in front of the reader
on the charging station to start
charging.*
Stop charging.
Optionally, hold your charge
card (RFID card) in front of
the reader on the charging
station to stop charging.*
Unplug the charging cable
from your car.
*For SEAT Charger Connect and SEAT Charger Pro only.
15
English

Status indication.
1 2 3
4
LED description
1Wallbox state
2Vehicle state
3House state
4RFID state
LED states
1Solid LED
2Flashing LED
3State remains unchanged
4O
1 2 3
4
16

State description Display
O or energy saving.
Wallbox is starting up.
Wait until the wallbox is
ready to charge.*
Configuration Manager
accessible via Wi-Fi
hotspot. Be aware that
charging is not possible
during this state.*
Idle - ready to charge.
Car plugged in,
charging paused
by wallbox, App, or
infrastructure. The
charging session will
continue when allowed.
17
English

State description Display
Car plugged in, not
charging, car paused /
fully charged.
Car plugged in, waiting
for charge card/
NFC input or remote
authorization.*
Car plugged in, charge
card/NFC authorization
pending.*
Authorization / Remote
Start accepted.*
18

State description Display
Car plugged in, charge
card/NFC rejected.*
Plug & Charge
authorization pending.*
Plug & Charge
authorization rejected.*
Car plugged in,
charging.
Note: If the wallbox shows other states than the ones described above, see Error states of the
wallbox for more information.
*For SEAT Charger Connect and SEAT Charger Pro only.
19
English

Prepare for
installation.
Content of delivery.
1
6 7 8 9 10 11 12
2
3
4
5
1Bezel × 1
7RFID cable* × 1
2Front cover × 1
8RS485 cable** × 1
3Main assembly × 1
A. SEAT Charger Pro
with kWh meter.
B. SEAT Charger or
SEAT Charger
Connect with feed-
through terminals.
9Fastening kit for
main assembly × 1
10 Fastening screws
for front cover × 1
11 Installation and
User Manual A × 1
12 Installation Manual B × 1
4Wall bracket × 1
5Charging cable × 1
6HMI cable × 1
*For SEAT Charger Connect and SEAT Charger Pro only.
**For SEAT Charger Pro only.
2020

Prerequisites for installation.
Danger.
Working on electric installations without proper
precautions will result in the risk of electric
shock, and thus cause severe injury or death.
•The installation must only be performed
by qualified electricians.
• Make sure that connection of the electrical
power cannot occur during installation.
• Put up caution tape and warning signs to mark
the working areas. Make sure no unauthorized
persons enter the working areas.
Choose location.
• Position the wallbox, where possible,
in surroundings where it is not exposed to
extreme sunlight and vulnerable to external
damage.
•The wall must have a flat structure and must
be able to hold a load of at least 100 kg.
•The minimum free space around thewallbox
must be a minimum of 300 mm.
Note: The below illustration indicates a standard installation height. Observe and comply
with the local accessibility regulations.
Your SEAT Charger Pro comes
equipped with a kWh meter,
and it is compatible with
different types of kWh meters.
For example, a 3-phase kWh
meter will also be compatible
in a 1-phase wallbox, as
shown in the following table.
Possible
combinations
1-phase
kWh meter
3-phase
kWh meter
1-phase SEAT Charger Pro
3-phase SEAT Charger Pro −
21
English