Sebury F2 User manual

F2- Fingerprint Access Control / Reader
Buzzer MiniUSB

1. Packing List
Name
Quantity
Remark
Fingerprint Reader F2
1
User Manual
1
Screwdriver
1
Rubber Bungs
3
6*27mm used for fixing
Self Tapping Screws
3
3.5*27mm used for fixing
USB Cable
1
2. Descriptions
F2 is a standalone fingerprint reader with exquisite & unique appearance and wiegand 26/34
output functions. The machine uses the most advanced fingerprint identification technology and
very safe, which supports to open door by following three ways: fingerprint/card/fingerprint+card.
It’s not only widely used in the commercial and industrial field, such as offices, factories,
warehouse, banks, laboratories, but in the small shops and households.
The operations of this product are all done by the software installed in your PC.
3. Features
Standalone Fingerprint reader
Supports USB & RS485/232 communication
3,000 fingerprint users and 3,000 card users
Supports to back up users’ data (fingerprint & card user info)
Supports to upload & download users’ data
Can be used as a standalone access control
Wiegand26/34 output for connecting to a controller
One relay output for control door
Built-in buzzer
Built-in light dependent resistor (LDR) for anti-tamper
Supports to open door by fingerprint/card/fingerprint+card
Fast Verification: Less than 1s base on full enrollment of 3,000 fingerprint
Two-year warranty

4. Specifications
Item
Parameters
CPU
32-bit RISC Core᧨120MHz᧨1MB FLASH᧨128K SRAM
Sensor
500DPI optic sensor
Cards
EM 125KHz
Capacity
Fingerprint: 3,000; cards: 3,000
Each user can enroll
2 fingerprints & 1pc card
ID number
Wiegand26 output᧶1~16777215 ; Wiegand34 output᧶1~4294967295
Verification mode
“or” mode᧶fingerprint or card (verify fingerprint or card will output wiegand signal)
“and” mode᧶card and fingerprint (after card verify requires fingerprint will output
wiegand signal)
Response time
<1s᧤full of 3,000 fingerprints᧥
FAR
< 0.0001 %᧤security level is 3᧥
FRR
< 0.1 %᧤security 3᧥
Reading Distance
5~10cm
Security level
1 ~ 5᧨default setting᧶3
Access interface
Wiegand output mode᧶Wiegand26 or Wiegand34 can be set
Relay output (option)᧶passive contact output᧤NOᇬNCᇬCOM᧥
Communication interface
RS485
9600~115200 BPS can be setting; no parity ;1stop bit; Flow Control: None
USB
USB1.1 Full speed
Input voltage
9V-15V DC
Working current
≤100mA
Working environment
Temperature ᧶-20°C ~ 80°C᧨Humidity ᧶20% ~ 80%

5. Installation
After connecting cable, mounting the device on wall
1). Pull the back plate shown below to open
2). With four screws to secure the appliance to the hole in the 4.
3). Connect the device to controller and computer according to the above definition.
Note᧶
᧶
For device safety, please do setting the communication password before using.
6. Wiring
Controller interface
᧤
4 cables
᧥
RS485 interface
᧤
2 cables
᧥
Cable color
Definition
Cable color
Definition
Red
Power supply :(9V
ᨺ15V
DC᧥
White
RS485A
Black
GND
Blue
RS485B
Brown
DATA0
Yellow
DATA1

Connection Diagram
7. Operation Introduction
Connect device to PC (by USB or RS485), then to run software ARControl.exe
(1). click “All Employee Info Management” to input employee information (ID, Name, Picture).
(2). click “Device Management” to set device parameters, and add the device to system.
(3). click “Fingerprint/card Enrollment” to enroll employee fingerprint and card to device.
8. Detailed user guide introduction
8.1.1 Software setting

1). Run ARControl.exe᧶
Figure 1
Input software password (default: admin), after successful, it displays main interface᧶
Figure 2
2). To Set the password and language of software᧶
Click “File”→select “Setting”, entering into software setting interface᧶

Figure 3

Setting software password᧶Input password and confirm setting.
Setting language:᧶Select “Chinese or English”, then click “Set”.
8.1.2 All Employee Info Management
Click “All Employee Info Management” in the main interface᧶
Figure 4
a) To add new employee᧶
᧶
Input ID, name and picture (requires *.bmp)
b) To modify employee information
᧶
Select the employee to be modified, change the relevant
information and click “Modify”.
Note
᧶
If modify ID number, should delete the employee first then input again.
c) To delete employee information: select the employee to be deleted then click “Delete”.
After modifying & keeping employee information management, click “Close” to ESC.
8.1.3 Device Management
Click “Device Management” in the main interface of software᧶

Figure 5
1). To Add Device
Device Name᧶
᧶
To set a name for the device.
Device ID
᧶
To input Device ID᧤1~255᧥, to make sure ID is unique for each one .
Communication Mode
᧶
USB or RS232/RS485.
ComPort
᧶
To design the RS232/RS485 COM PORT of PC.
Baud Rate
᧶
To set baud rate when choose RS232/RS485 for communication. If to change baud
rate, the baud rate of old device and new baud rate are required to fill, then restart the
device, which will be communicated by new baud rate.
Password
᧶
For setting communication password for device and PC, to improve the safety of device.
Password are consist of 14 letters and numbers, please do remember the password after
setting, once forget, it should be sent back to factory to format and all the registration
information will be lost.
Note
᧶
For device safety, please do setting the communication password before using.
Wiegand Mode
᧶
Wiegand26 or Wiegand34.
Identification Mode
᧶
Card or FP᧶Once card or fingerprint verification successful, it will output
wiegand signal.
CardandFP᧶Once card and fingerprint verification successful, it will output
wiegand signal.

FP Time Out᧶
᧶
0~60s can be set, default setting: 30s, used for enroll fingerprint: to detect if press
fingerprint after command, time out will exit to enroll.
For setting “0” means no time out for judging.
Standby
᧶
0~60s, Device will enter into standby mode if without any operation during the setting time.
The device will be activated if press a finger or a proximity card or there is
communication command from PC.
For setting "0" means no sleep mode, default setting: 60 seconds.
Security level
᧶
1~5 levels᧨default setting is 3᧨level 1 is the most high security level.
After setting the above parameter, click “Add” will register the device to software.
2). To Set/Modify device parameters
To select the device in the Device List, after inputting the above parameters.
If using USB communication mode, click “Set Information” to keep setting successfully.
If using RS485 communication mode, make sure the consistency of Device ID and baud rate with the
present device.
After setting successfully, device will working as the setting parameters.
3). To get device information
To select the device in the Device List, click “Get Information”, will get the device parameters and
total enrolled user data, fingerprint users, cardholders and the device’s version info.
Note
᧶
1. Please make sure Device ID & Baud Rate are correct when get information from device by
RS485.
2. If no device ID & baud rate, please choose USB to get the information first on condition
that know communication password.
4). To Initialize the Device
To Select the device in the Device List, click “Device Init”᧨all the enrolled user information will be
deleted , and resume to the following default parameters:
Note: Device Initialization will not delete communication password.
Name
Default setting
Device ID
0
Baud rate
9600BPS
Wiegand mode
Wiegand26
Verification mode
Card or fingerprint
Security level
3

5). Brightness Auto Adjust
After long time using, the sensor backlight might lower down, which may lower the identify rate,
in this case please adjust the lightness.
Note᧶Device has been set the auto brightness control, so no need to adjust all the time.
Adjustment Method:
To select device in the Device List, click “Brightness Auto Adjust”, after see “please screen
sensor’s light”, cover the sensor windows with hand, click “OK” to confirm.
After setting all information, click “close” to ESC.
6). To Delete Device
To select the device in the Device List, click” Delete”.
Warning᧶
᧶
To delete device will clear all the user information in the database, please handle with
care.
Once to delete the device by mistake, please using the function of “Upload/Download” to
back up device’s user information.
8. 1.4 To Register, delete fingerprint/card
After inputting user information and Device Setting, click “Fingerprint/card Enrollment”᧶
Figure6
a) To select the device from “Device Name” to enroll fingerprint and cards
b) To click “Select User” to select the user who will enroll fingerprint and cards:

Figure 7
c) To Enroll fingerprint and card᧶
᧶
select user to be enrolled, click “Select” back to
Employee Mange interface᧨click “Enroll” to enter enroll interface᧶
Note
᧶
One user can be enrolled with 2 fingerprints and 1pc card.
If the user who was enrolled in the device needs to update the fingerprint or card, please tick
the check box “Update”, otherwise the software will not allow enrolling for this user.
Figure8 Figure9
A
ᇬ
To Enroll fingerprint users
᧶
Connect with USB and tick the check box “Upimage” to view the fingerprint image in real
time when enroll.

Click “FP0 Enroll”᧨press one fingerprint, system hints “Uploading Image”→“Release your
Finger” →“two more”→“release your finger”→“one more” →“release your finger”᧨press three
times to finish fingerprint enrollment.
Click “FP1 Enroll”᧨step same as above to enroll second fingerprint.
Bᇬ
ᇬ
To Enroll card users
᧶
Click “ Card Enroll” in the “Enroll” interface, system hints “Input your Card”᧨press card after
system read card hinting “Release your Card”᧨the device will detect and show the status after
releasing cards᧶
“Result = success and reference user’s ID= and Card ID=”.
Click “Exit” to finish enrollment and back to “Fingerprint/card Enrollment” interface→click
“select user” to choose next user →click “Enroll” to enroll all users as same steps.
d). To Delete user
᧶
in the “Fingerprint/card Enrollment” interface, select the device name &
users to be deleted᧨click “Delete” will delete the appointed user from device.
e). To Delete all users
᧶
in the “Fingerprint/card Enrollment” interface, select the device, click
“Delete all” will delete all users from device.
8.1.5 To Upload/Download
Upload/Download is used to synchronize the fingerprint and card data of device and Dada Base in
PC. Click “Upload/Download” on the Main interface:

Figure 10
1). Upload᧶
᧶
To back up the fingerprint and card data from device to software database in PC.
A. If the device is deleted by mistake:
Click “from device to PC” in the Upload/Download (no need to select device)::
Figure 11
After setting all the parameters, click “ok”᧶

Figure 12
Input device name, then Click “ok”, entering into “Upload/Download” interface᧶
The blue progress bar shows the uploading progress
B. To Upload the fingerprint and card data to new software in PC
To input all the employee information in “All Employee Info Management”, operated
following the above step A to upload employee’s info in each device’s data to PC.
2). To Download Data᧶
᧶
To download the fingerprint and card data from software in PC to
device. It is applied to following cases᧶
A. If all enrolled data in device were deleted after initializing the device,
B. If needed to manage several devices, it is available to manage all data in one device by
putting it in the management center then to select some employee to download their data
to specified devices.
Operation procedures:
1. To select the device in the left of “Upload/Download” interface→all users’ information
list will be shown in middle box (shown as Figure 10)
2. To select the users or all users click “select all”
3. To select the device to be downloaded᧤tick the check box before the ‘device ID’᧥
4. To click “from PC to device ”: the blue progress bar shows the uploading progress.
5.To click “close” to finish downloading.
8.1.6 To Scan Device
᧤
To detect the state of device in RS485 Network
᧥
For detecting the state of RS485 network (online or offline).
Click “Device Scan” in Figure2 to scan device in Main interface.

APPENDIX ONE APPLICATION INFORMATION
A1.1 Backup Data Base
To Run software ARControl.exe will create the following 3 database files under the directory᧶
᧪Emp.db (Employee information)
᧪DeviceInfo.db᧤device setting parameter database᧥
᧪EnrollData.db ᧤employee enrollment database᧥
After adding all the devices to software, inputing all the employee information, and enrolling
all employees’ fingerprint and card to device, also put into formal using, copy above 3 database
files to save.
A1.2 Right pose of pressing finger
APPENDIX TWO INSTALLATION AND CONNECTION
A2.1 F2 Connection defination᧶
᧶
Red: Power supply input᧤9Vᨺ15V DC᧥
Black: GND
Brown᧶DATA0
Yellow: DATA1

White: RS485A
Blue: RS485B