Sebury sReader-w User manual

sReader-w / sReader-s
User Manual
Please read this instruction completely and keep it properly

Product Introduction
sReader adopts high-strength ABS plastic appearance.EM,HID and IC card reading
are supported.Bluetooth analog card Wiegand output function of mobile phone,
built-in high integration micro-controller and simple circuit are applied. safety and
reliability are assured. sReader is cost effective and durable, suitable for office,
communiy and other context using.
Performance Parameters
Body Material:
Bluetooth Function:
Card Type:
Reading range:
Output format:
Input voltage:
Quiescent current:
Operating temperature:
Operating humidity:
ABS Plastic
Mobile phone Bluetooth analog output card number，shared by
one administrator to multiple users
EM, HID card (125kHz)
IC card (including Mifare and CPU card, 13.56MHz, ISO14443a)
≤ 5cm
Wiegand 26-37bit (Default 26bit, Customized for other formats)
DC12 ± 2V
≤ 50mA
- 20 ～ 50 ℃
0-95%

sReader-w Dimension: 120 * 85 * 23mm
sReader-s Dimension: 107 * 48 * 23mm
Ingress protection: IP65 (water and dust-resistant)
Wires and Instruction
1 Red +12V
2 Black GND
3 Green D0
4 White D1
5 Brown LED
6 Yellow BZ
Serial No. Color Definition Instruction
Positive pole
Negative pole
Wiegand output
Wiegand output
Green LED control input
Buzzer control input

Packing List
Card Reader*1
Self Tapping Screw KA4*25mm ( sReader-w*4 ）
Punch Sticker*1
User Manual*1
Screw Hole Decoration Piece*1
Expansion Rubber Bung Φ6*24mm ( sReader-w*4）
sReader-w / sReader-s
User Manual
Please read this instruction completely and keep it properly

Installation
Stick the punch sticker on the wall. Drill 2 Φ6mm intallation holes with purcussion drill
with the depth of 26mm.（4 holes for sReader-w ）
Drill Installation Holes

Drill Φ10mm hole for outlet with the depth according to the practical situation of
electric lines.
Drill the Hole for Outlet

Click 2 expansion rubber bungs into the installation holes （4 expansion rubber
bungs for sReader-w）
Click Expansion Rubber Bung

Fix the back shell on the wall with 2 K4*25 self tapping screws（4 screws for sReader-w）
（The percussion drill,hammer and screwdriver in figure2,3 and 4 should be self prepared.）
Fix the Back Shell

Put the outlet cables through the Φ10mm hole and connect the needed cables.(Pack
the useless cables with the insulating tape.)
Connect Cables

Put the front shell on the back shell. Install the tamper screw from the bottom of the
device with screwdriver and stick the screw hole decoration piece onto the device.
Install the Front Shell and Screw Hole Decoration Piece

Functional Description
Wiegand Data Description
1. The Wiegand format of the card reader can be customized according to the customer's
needs. The format range is: 26 ~37bit Wiegand.The EM card and IC card output 26~37bit
Wiegand in the factory format. HID card has nothing to do with factory Settings, and automat-
ically outputs 26 ~ 37bit Wiegand in card format.
2. The green line D0 is Wiegand signal data line 0, and the white line D1 is data line 1.Usually
high level, low level represents the output data.Low level pulse width is 40uS,The pulse width
interval is 2mS.The following figure illustrates the waveform of data "0101".
1. When swiping the card, the indicator light turns green and the reader has a steady
beep.Then indicator light turns red, wiegand signal is output at the same time.
2. When the LED line is lowered, the indicator light turns green; when the LED line is set
high, the indicator light turns red.
3. When the BZ line is lowered, the buzzer rings. When the BZ line is lowered for more than
30 seconds or set higher, the buzzer will return to normal.
4. When the machine is illegally disassembled, the buzzer will ring and automatically stop
after 1 minute.

2. Administrator's Mobile Phone Operations
Only one administrator is permitted on sReader. Administrators must be added first,
other users can be added by administrators. Administrator is added as follows:：
⑴ Turn off the power supply and restart sReader. Take follow up actions in 10
minutes
⑵ Open APP, the user instructions interface is shown as in Figure 1. Tap "Scan QR
Code" to scan the QR code on the of back shell of sReader (Figure 2) The addition is
successful when the interface is shown as in Figure 3.
Mobile Phone Operating
1.Download and install APP
Scan the following QR code, or Android search：“Access Control ”,
Apple store search：“BleAccess”.
ios Android
Search "BleAccess" in Apple store to
download the BLE App.

1 2

⑶ Click the device name at the top of Figure 3.Enter a new device name in the
dialog box for modifying the device name( Figure 4). Click OK to confirm the new
name(Figure 5) as shown in Figure 6. The last modified name is displayed when
sharing to other users.
3 4

5 6

7 8
Administrators add users as follows:
⑴ Click "User Management" in Figure 6 and enter the list of users as shown in
Figure7. Administrator is automatically added, the name of administrator can not
be modified.
⑵ Click "Add User" to add a user bar, as shown in Figure 8.

9 10
⑶ Click the user bar to enter the user's QR code page as shown in Figure 9. After
modifying the user's name, click "Change user information", the QR code
information will be changed accordingly. After modification, the QR code contains
all the information assigned to this user (Figure 10).
Put the front shell on the back shell. Install the tamper screw from the bottom of the
device with screwdriver and stick the screw hole decoration piece onto the device.

11 12
Administrators delete users as follows:
Swipe left the user bar to see a "delete" button, click "delete" and "confirm delete" to
delete the user from the list.

3.Other users add device
Administrator opens APP and enters the page in Figure 10, showing the user's QR code.
The user opens the APP and enters the page in Figure 1. clicking on the "Scan QR Code"
to scan the user's QR code on the administrator's mobile phone. Adding devices is
successful when the interface is shown as Figure 3.
4.Users open doors with mobile phones
Administrators and users can open the door by APP in the same way. The operation is
as follows:
⑴ Open the APP to see the device list page as Figure 13 if the device has been added.
Press the small button on the left side of the list bar directly, the phone will vibrate for a
moment. The door is open when the button turn blue and show "Open"(Figure 14). The
button will be restored to its original state in 1 second.
⑵ Press the area of device list except button to enter the device home page(Figure 13 ).
"User Management" button is not displayed in normal users’ interfaces. Press the big
button in the center of the page, the phone will vibrate for a moment. The door is open
when the button turns blue and shows "Open"(Figure 16). The button will be restored to
its original state in 1 second.

13 14