Sebury K3-3 User manual

2 3
4
+12V LOCK+
LOCK-
+12V
GND D0 D1 D_IN(LED)
OPEN(BZ)
LOCK+ LOCK-
PUSH +12V GND NO CO M NC
Open Door delay
0(50ns) for type A lock
A Lock
5 6 7
+12V
GND D0 D1 D_IN(LED)
OPEN(BZ)
LOCK+ LOCK-
Lock
Exit Button
Door Contact
DC12V
Power
INSTRUCTION
MANUAL
K3-3
Standalone Access Control
1.1 Introduction
K3-3 is a standalone, convertible integrated reader and access control.
It controls electronic lock, exit button, and the magnetic contact switch
on the door. If the unit is connected to a standard access control unit,
then it functions as a reader. The unit accepts up to 500 users, allow
entry via a 4-6 digits PIN and/or by presenting a proximity EM card.
1. Introduction, Features and Specifications
2.Installation and Wiring Instructions
Electronic lock schematic diagram
Wiring diagram (DC 12V power supply)
Wiring diagram (special power supply for access control)
Red Black Green White Brown Yellow
Orange
Blue
Red Black Green White Brown Yellow
Orange
Blue
K3-3 Standalone Access Control
K3-3 Standalone Access Control
3. Wiring Definition
+12V DC
GND
D0
D1
Functionality
Buzzer
Red
Black
Green
White
Color
Brown
Yellow
Description
LED
+12V Power Input
GND
Wiegand output D0
Wiegand output D1
Green light input
Buzzer input
4. Master keypad Operation
Enter Master Operation Mode. It will return to normal mode if
there is no right Master PIN input in 5 seconds. After input of right
master PIN, it will also return to normal mode if there is no valid
operation in 30 seconds. Press “#” to confirm the input number,
return to previous menu by press “*”, the LED will indicate the
operation mode.
Exit Button
Door Contact
B Lock
special power supply
Remark:
① 8 digits card number, such as 118,32319, some cards has no
mark of the first 3 digits 118, remains 32319. It requires to add
card by read card, adding cards by input card number is not
acceptable;10 digits card number, such as 0007765567, some
cards has no mark of the first 3 digits 000, remains 7765567,
requires to input 10 digits 0007765567 by add 000 before
7765567.
② A PIN 1234 is added for a card, it can not be used to unlock the
lock, can be used to change PIN.
③ After one card is added , you can continue to add other cards
or PIN without exiting the mode.
④ Type A electronic lock: Fail Secure lock(Unlock when power
on), such as Electronic Controlling Lock.
⑤ Type B electronic lock: Fail Safe lock(Unlock when power off),
such as EM Lock, Electronic Bolt Lock, etc.
Master Operation
Red Flash Red Function
6-8 digits master PIN，#Master mode
(default 888888)
Access control mode settings
Flash
Red Function
Red and Green LED ON
0 6-8digits new PIN, #,
repeat 6-8digits new PIN, #
Change
master PIN
Read card
1-500 (ID) , #, Read card Add one card②,
or add more than
1 cards③
8 or 10 digits card number①,
1-500 (ID) , #, 8 or 10 digits card
number, #
1-500 (ID) , #, 4-6 digits user
PIN, #
Add one user PIN,
or add more than
1 users PIN
Read card
8 or 10 digits card number, #
1-500 (ID) , #
Delete one card,
or delete more
than 1 cards
Delete one user,
or delete more
than one users
2
0000, # Delete all users
and PIN
0, #
1, #
2, #
To unlock by card
To unlock by
card and PIN
To unlock by card
or PIN (default)
3
1-99, #
Lock strike release
time: 50mS
0, #
Lock strike release
time:1-99S (default
5S)
4
Type A electronic
lock④
Type B electronic
lock ⑤ (default)
0, #
1, #
5
Reader mode settings
Flash
Red
Flash
Red and
Green
Red
Green Function
0, #
1, #
7
1
3
Reader mode
Access control mode (default)
4-6 digits key press sends card
number
0, #
Each key press sends 4bit output
data (default)
1, #
Each key press sends 8bit output
data
2, #
5. User Settings
5.1 To unlock the door for card users,
Read valid card once, the electronic lock will unlock
5.2 To unlock the door for card and PIN users
Read valid card once then enter 4-6 digits PIN#, the lock will unlock
5.3 To unlock the door for card or PIN users
Read valid card once, the lock will unlock
Or enter 4-6 digits PIN#, the lock will unlock
5.4 To change the PIN of a PIN user
*, Read Card, input 4-6 digits old PIN , #, input 4-6 digits new PIN,
#, repeat input 4-6 digits new PIN, #.
or*, Input 1-500 (ID), #, input 4-6 digits old PIN, #, input 4-6 digits
new PIN, #, repeat input 4-6 digits new PIN, #.
Remark: For PIN users without card, must get ID number and
initial PIN from the master. For users with card, must read card to
change initial PIN.
6. Alarm
6.1 Anti Tamper Alarm
While anti-tamper function is valid, if the access control unit is
removed from the cover, the buzzer alarm will activate.
6.2 Magnetic Contact Switch on the Door
While connecting to a door position switch, if door-forced
conditions are supported, the buzzer alarm will activate if the
door is forced open..
6.3 Remove the alarm
While anti-tamper and door status alarm is valid, read valid card,
or input master code can remove the alarm. The alarm will also
stop after 1 min if there is no operation.
Power off, press *, power on, the red and green LED will turn on,
release it until hear two beeps, then will hear one beep and the
red LED will turn on, resets to factory default setting is done.
Reset to factory default, the users' information is still retained.
7. Reset to Factory Default
8. Sound and Light Indication
Red LED Green LED
Operation Status Buzzer
Standby
Card & PIN inputting
Slow flash
3 Short Ring
OFF
OFF
Press Key
Read Card
Door Open
Operation Successful
Operation failed
PIN Inputting
1st menu
2nd menu
Under Setting
Alarm
ON
OFF
OFF
ON
ON
ON
OFF
Slow flash
Slow flash
Slow flash
OFF
OFF
ONON
OFF
Quick flash
Long Ring
Long Ring
Long Ring
Short Ring
Alarm
9. Reader Application (wiring diagram)
+12V
GND D0 D1 D_IN(LED)
OPEN(BZ)
LOCK+ LOCK-
Red Black Green White Brown Yellow
Orange
Blue
Reader Mode
+12V GND D0 D1 LED BZ
Access Control
Set the unit to reader application, functions as below:
The wire in green (D0) is the wire for Wiegand 0, and the wire
in white is the wire for wiegand 1. The pulse width for low voltage
is 40uS; and the time interval is 2mS.
There are 3 formats for the card output by Wiegand 26.
Format 0: 4-6 digits key press sends card number format: Input
4-6 digits PIN, press “#”, output a Wiegand 26, 10-bit decimal
card number. For example, input password 999999, the output
card number is 0000999999, could be displayed by 10-bit
decimal card number display equipment.
Format 1: Each key press sends 4 bits data, the corresponding
relationship is:
1 (0001) , 2 (0010) , 3 (0011)
4 (0100) , 5 (0101) , 6 (0110)
7 (0111) , 8 (1000) , 9 (1001)
* (1010) , 0 (0000) , # (1011)
Format 2: Each key press sends 8bit output data, the first 4 digits
is ones-complement code for the last 4 digits, the corresponding
relationship is:
1 (11100001) , 2 (11010010) , 3 (11000011)
4 (10110100) , 5 (10100101) , 6 (10010110)
7 (10000111) , 8 (01111000) , 9 (01101001)
* (01011010) , 0 (11110000) , # (01001011)
2mS
+5V
+5V
D0
D1
0V
0V
40uS
40uS
2mS
1.2 Features
Backlit keypad, multi-function, operating as access control or card
reader, suitable for various occasions.
1.3 Specifications
> Operating voltage range: DC12-24V
> Static input current: ≤20mA
> Max proximity card read range: 5-8cm
> Excitation Frequency: 125KHz
> Card transmit format: Wiegand 26
> Keypad transmit format: 4-6 digits key press to output card number
format. Each press outputs a 4 bits or 8 bits data.
> Size (Height×Width×Depth): 90×60×27mm
> Operating temperature range: -40～60° C
> Operating humidity: 0～95% (non-condensing)
Slow flash
1