ZKTeco C2-260 User manual

Quick Start Guide
Version: 1.1
Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between
the actual product and the written information in this manual.
C2-260/inBio2-260 Access Controller

4 Diodes4 Screws &Anchors 2 Screwdrivers
C2-260 / inBio2-260
NC COM NO SEN GND BUT NC COM NO SEN GND BUT NC COM NO NC COM NO
AUX GND AUX
GND 485B 485A
12VRD GND 485B 485A
+12V GND +12V GND
LOCK1 LOCK2 AUX OUT AUX IN
PWR
RUN
TCP/IP
RS485 READER VOUT POWER
RS485 DIP
What’s in the Box
1

Safety Precautions
Do notexpose to direct sunlight,water, dust and soot.
Do notplace any magnetic objects nearthe product. Magnetic objects such as
magnets, CRT, T V, monitors or speakers may damage the device.
Do notplace the device near any heating equipment.
Prevent water, drinks or chemicals leaking into the device.
This product is not intended for use by children unless they are supervised.
Do notdrop or damage the device.
Do notdisassemble, repair or modify the device.
Do not
Remove
towel instead ofwater.
Contact your supplier in case of any query.
2
The following precautions are to ensure user's safety and prevent any damage. Please read the
instructions carefully before installation.
dust or dirts regularly. While cleaning, wipe the dust o with a smooth cloth or

NC COM NO SEN GND BUT NC COM NO SEN GND BUT NC COM NO NC COM NO
AUX GND AUX
GND 485B 485A
12VRD GND 485B 485A
+12V GND +12V
GND
LOCK1 LOCK2 AUX OUT AUX IN
PWR
RUN
TCP/IP
RS485 READER VOUT POWER
RS485 DIP
Ethernet Port 12V Power in
Figure 1
2 Lock & Door Sensor 2 Aux Input2 Aux Output
USB Port RS485 Reader
12V Power out DIP Switch
RS485 Communication
3
Product PIN Diagram

real-time monitoring status.
LINK Solid Green LED indicates TCP/IP com-
munication is normal.
Flashing (ACT )Yellow LED indicates data
communication is in progress.
Solid (POWER) Red LEDindicates the panel
is powered on.
NC COM NO SEN GND BUT NC COM NO SEN GND BUT NC COM NO
LOCK1 LOCK2 AUX OUT
PWR
RUN
TCP/IP
RS485
RS485 ADD
Figure 2
Figure 3
NC COM NO SEN GND BUT NC COM NO SEN GND BUT NC COM NO
LOCK1 LOCK2 AUX OUT
PWR
RUN
TCP/IP
RS485
RS485 ADD
NC COM NO SEN GND BUT NC COM NO SEN GND BUT NC COM NO
LOCK1 LOCK2 AUX OUT
PWR
RUN
TCP/IP
Figure 4
Figure 5
4
LED Indicators
Slowly ashing Green LED indicates normal
working status of the system.
TCP/IP continuously ashing Yellow LED
indicates data transmission.
TCP/IP slowly ashing Yellow LED indicates

POWER
POWER
Figure 7
Figure 6
NC COM NO
SEN
GND BUT NC COM NO SEN GND BUT
NC COM NO NC COM NO
AUX GND AUX
GND 485B 485A
12VRD GND 485B 485A
+12V
GND +12V
GND
LOCK1 LOCK2 AUXOUT AUXIN
PWR
RUN
TCP/IP
RS485 READER VOUT POWER
RS485DIP
Step 1
Drill holes on the wallStep 2
Fix the device with fourscrews
Step 1
Fix the guide rail on the wallStep 2
Fix the device to the rail mounting.
Wall Mounting
Rail Mounting
5
Panel Installation

7
RS485
Ethernet Cable
P
U
S
H
T
O
T
E
S
T
W
E
E
K
L
Y
P
U
S
H
T
O
T
E
S
T
W
E
E
K
L
Y
FIRE
ALARM
DetectorIR Sensor
485 Convertor
FloodlightExit Button
Normally Open LockNormally Close Lock
12V DC Power Supply
The auxiliary input may be connected to infrared body detectors, re alarms, or smoke detectors. The auxiliary
output may be connected to alarms, cameras ordoor bells, etc.
Figure 8
RS485 Reader
NC COM NO SEN GND BUT NC COM NO SEN GND BUT NC COM NO NC COM NO AUX GND AUX
GND 485B 485A
12VRD GND 485B 485A
+12V GND +12V GND
LOCK1 LOCK2 AUX OUT AUX IN
PWR
RUN
TCP/IP
RS485 READER VOUT POWER
RS485 DIP
Panel Installation
6

Sensor
CEILING
INDOOROUTDOOR
C2-260/inBio2-260 Access Control Bundle
Electric Lock
Exit Button
Indoor RS485 reader
Outdoor RS485 reader
Figure 9
Ethernet Communicationwire RS485 Communication wire
220/110 V Input
7
Installation Diagram

NC COM NO
SEN GND BUT NC COM NO SEN GND BUT
NC COM NO NC COM NO
AUX GND
AUX
GND 485B 485A
12VRD
GND 485B 485A
+12V
GND +12V
GND
LOCK1 LOCK2 AUX OUT AUX IN
PWR
RUN
TCP/IP
RS485 READER VOUT POWER
RS485 DIP
C2-260 / inBio2-260
Router
TCP/IP 485A
+12V
485B
GND
DC12V
Note:
1. It’s recommended to connect maximum four readers to one C2-260/inBio2-260.
2. A single RS485 reader interface can supply a maximum of 750 mA (12V) current. So the
entire current consumption should be less than this max value when the readers share
the power with the panel.
3. Only inBio2-260 supports connection with FR1200 readers.
#1Reader #2Reader #3Reader FR1200
(inBio2-260)
8
RS485 Readers Connection

Connection with DM10
9
Additional Modules of RS485
NC COM NO
SEN GND BUT NC COM NO SEN GND BUT
NC COM NO NC COM NO
AUX GND
AUX
GND 485B 485A
12VRD
GND 485B 485A
+12V
GND +12V
GND
LOCK1 LOCK2 AUX OUT AUX IN
PWR
RUN
TCP/IP
RS485 READER VOUT POWER
RS485 DIP
C2-260 / inBio2-260
Note:
1. A C2-260/inBio2-260 can connect to maximum eight DM10 modules..
2. Each DM10 module requires a separate power supply.
Router
485A
485B
GND
DC12V
DC12V
DM10 DM10 DC12V
TCP/IP