6
English
7
English
DAY AND TIME SETTING
Day hand
CROWN
Pull out to second click when Small second
hand is at the 12 o'clock position.
▼
Turn clockwise to advance Hour and Minute
hands until Day hand is set to the desired day
of the week.
▼
Turn to set the time.
▼
Push back completely in accordance with a
time signal.
1. To advance the day hand quickly, turn back the hour and minute hands 4 to 5 hours beyond the
pointthe day changes (between 11:00 p.m. and 4:00 a.m.), and then advance them again until
the day hand is set to the next.
*The day hand will not move back by turning the crown counterclockwise.
2. After the day hand reaches the last day of the week, turn the crown clockwise and the hand will
return to the first day of the week (retrograde day indicator).
3. When adjusting the day hand, turn the crown slowly.
4. The 24-hour hand moves correspondingly with the hour hand.
5. When setting the hour hand, check that the 24-hour hand is correctly set.
6. When setting the minute hand, advance it 4 to 5 minutes ahead of the desired time and then
turn it back to the exact time.
clockwise
counterclockwise
CROWN
Pull out to first click when Small second hand
is at the 12 o'clock position.
▼
Turn to set the time.
▼
Push back completely in accordance with a
time signal.
1. The 24-hour hand moves correspondingly with the hour hand.
2. When setting the hour hand, check that the 24-hour hand is correctly set.
3. When setting the minute hand, advance it 4 to 5 minutes ahead of the desired time and then
turn it back to the exact time.
clockwise
counterclockwise
● CAL. 6G34 ● CAL. 6G27
8
English
9
English
1.
Do not set the date hand between 9:00 p.m. and 2:00 a.m. Otherwise, it may not turn prop-
erly.
2. While setting the date hand, check that it moves properly in one-day increments.
3. It is necessary to adjust the date on the first day after a 30-day month and February.
DATE SETTING (for Cal.6G34)
CROWN
Pull out to first click.
▼
Turn counterclockwise to set Date hand to the
desired date.
▼
Push in.
Date hand
BATTERY CHANGE
The miniature battery which powers your watch should last approximately 3
years. However, because the battery is inserted at the factory to check the
function and performance of the watch, its actual life once in your possession
may be less than the specified period. When the battery expires, be sure
to replace it as soon as possible to prevent any malfunction. For battery
replacement, we recommend that you contact an AUTHORIZED SEIKO DEALER
and request SEIKO SR626SW battery.
●
Never short-circuit, heat or otherwise tamper with the battery, and never
expose it to fire. The battery may burst, become very hot or catch fire.
●The battery is not rechargeable. Never attempt to recharge it, as this may
cause battery leakage or damage to the battery.
CAUTION
WARNING
●Do not remove the battery from the watch.
●If it is necessary to take out the battery, keep it out of the reach of
children. If a child swallows it, consult a doctor immediately.
10
English
SPECIFICATIONS
1 Frequency of crystal oscillator ................. 32,768 Hz (Hz = Hertz...Cycles per second)
2 Loss/gain (Monthly rate) .......................... Less than 20 seconds when used on the wrist
within normal temperature range (5 ºC~35 ºC)
(41 ºF ~ 95 ºF)
3 Operational temperature range ................ –5 ºC ~ +50 ºC (23 ºF ~ 122 ºF)
4 Driving system.......................................... Step motor
5 Display system
Time ..................................................... 24-hour, hour, minute and small second hands
Day....................................................... Indicated by day hand (6G34)
Date ..................................................... Indicated by date hand (6G34)
6 Battery ...................................................... SEIKO SR626SW, 1 piece
7 IC (Integrated Circuit) ............................... C-MOS-IC, 1 piece
* The specifications are subject to change without prior notice for product improvement.
