SelectBlinds Fashion Color Power Touch Series Installation guide

POWER TOUCHTM RECHARGEABLE
Installation & Care Instructions 152733
4/19/2017
Roller Shades
Fashion Color Collection Light Filtering Roller Shades

2
GETTING STARTED
A few simple tools are required:
- Measuring tape
- Power drill, drill bits
-
1⁄4”Hex head and/or Phillips driver bit
- #2 Phillips head screwdriver
- Pencil
Additional fasteners other than those sent with
your shade may be required depending on the
mounting surface. Wallboard and plaster require
the use of anchors such as expansion or toggle
bolts. Brick, tile or stone need special plugs and
drill bits. Remember to always pre-drill holes in
wood to avoid splitting.
STEP 1: BRACKET INSTALLATION
PN: 20201012
Mounting
Bracket
1 1⁄4”Hex
Head
Bracket
Screw
Head rail Extension
and Side mount
Bracket
(optional)
Hold
Down
Bracket
(optional)
PN: CS5402 PN: CS1000 PN: CS1101
Shades are shipped with the required number of brackets
for proper installation. End brackets should be located
approximately 3” from either end. Depending on the width of
the shade, additional brackets may be necessary, evenly spaced
between the two end brackets.
Using the installation bracket as a template, measure to the
center of the bracket and mark the hole locations with a pencil
for drilling.
Brackets must be in line and level. Shim brackets on inside
mounts if necessary. e head rail must be level for the shade
to operate properly.
Shade Width # of Brackets
Up to 40” 2
>40” - 72” 3
>72”- 84” 4
>84” -114” 5
Spacer
Block
(optional)
PN: CS2000
3” 3”
Charger
PN: CS5199
Mounting
Brackets for
Shades without
head rail
PN: CS5002(W or BLK)
CS5008 (W or BLK)
CS5529
CS5530
Depends on size of
shade
SHADES WITH HEAD RAIL
Cable Tie
(for No
Head Rail
Shades)
Cable Tie
Mounting Base
(for No Head
Rail Shades)
PN: CWV4024 PN: CS5201
Wand Hanger
Screws
PN:CS52071

3
EXTENSION BRACKETS (OPTIONAL)
Optional extension brackets are used to project the back of the
shade up to 2 1⁄2”from the mounting surface.
Attach the mounting bracket to the extension bracket with the
nut and bolt provided.
SIDE MOUNT (OPTIONAL)
Measure from window sill up to desired mounting position on each side
of the window frame. Mark position.
Mount side mount brackets on each side of window frame as shown.
Make sure to conrm the head rail will sit perfectly level.
Once side mount brackets are installed and properly positioned, attach
the mounting brackets using the nuts and bolts provided.
Side Mount
Minimum 2” surface
Outside Mount with Extension Brackets
Minimum 2” surface
SPACER BLOCKS (OPTIONAL)
Each spacer block projects brackets 3⁄8”away from mounting surface.
Make sure the brackets are level and aligned.
Attach using two screws. Screws should be long enough to secure the
bracket to the mounting surface. Outside Mount with Spacer Blocks
2”
2 1⁄2”
OUTSIDE MOUNT
e minimum mounting height for outside mounted shades is 1”.
Make sure the brackets are level and aligned.
Attach using two screws.
Outside Mount
Minimum 1”surface
1”
2”
INSIDE MOUNT
e minimum mounting depth for an inside mount is 1”.
A minimum of 3 3⁄4”is needed to fully recess the shade.
Make sure the brackets are level and aligned.
Attach using two screws. Inside Mount
Shallow Mount - Minimum 1”surface
Flush Mount - Minimum 3 3⁄4”surface
1”

4
Idler Side Bracket Motor Side bracket
Foot
T-Hook
e installation brackets are always mounted so that the
inner surfaces face each other.
Brackets must be in line and level. Shim brackets on inside
mounts if necessary. e head rail must be level for the shade
to operate properly.
SHADES WITH NO HEAD RAIL
Inside Mount
Minimum 1 1⁄2” surface
Outside Mount
Minimum 1 1⁄2” surface
1 1⁄2”
1 1⁄2”
STEP 2: CONNECT WAND
While holding wires in the channel of the wand holder, attach
the wand holder to the end of the motor with the screws
provided, using a #2 phillips head screwdriver. Be sure that the
wires are not twisted or pinched.
Plug the wand wires into the motor wires.
STEP 3: SHADE INSTALLATION
Center the shade in the window opening and
push the head rail into the mounting brackets as
shown.
Push the rail back until it
is fully engaged
SHADES WITH HEAD RAIL
wires
SHADES WITH HEAD RAIL
SHADES WITH NO HEAD RAIL
Plug the control wire into the wand wire . e plugs will only t
together one way. e wires are bundled at the back of the head
rail.

5
Press the DOWN or UP button to lower or raise the shade. Press the STOP/
FAVORITE to stop the shade at the desired position.
To fully raise or lower the shade, simply press the UP or DOWN button and
then release. e shade will automatically stop when it reaches the upper or
lower limit. (If the upper or lower limits are not set at the desired positions, see
the Adjust Motor Limits section on the next page)
Note: Upper and lower limits stops are set at the factory. An intermediate, or
“favorite” position is not set at the factory. See page 6 for more information.
OPERATION
Up
Down
Stop/Favorite
Insert the foot of the motor-side bracket into the slotted center
hole of the motor end of the fabric roll.
Set the post of the idler end into the V of the support bracket.
Rotate the T-hook on the support bracket to lock in the post
and secure the fabric roll.
Bundle excess wire and secure with the cable tie mounting
base and cable ties.
Nub
Support Bracket
Fig.15
Idler Post
V slot
SHADES WITH NO HEAD RAIL

6
FAVORITE POSITION
CHANGING A FAVORITE POSITION
Use the UP or DOWN buttons to position the shade at the new desired
“favorite” position. First press and hold the SETTING button on the back of
the wand. While holding the SETTING button press and hold the UP button.
Release both buttons when the shade beeps.
is establishes a new “favorite” position and erases the old.
SETTING AND USING A FAVORITE POSITION
Use the UP or DOWN buttons to position the shade at the desired “favorite”
position. First press and hold the SETTING button on the back of the wand.
While holding the SETTING button press and hold the UP button. Release
both buttons when the shade beeps.
With the shade at either the upper or lower limit, simply press the STOP/
FAVORITE button to bring the shade to the “favorite” position. To go to the
“favorite” position from any other location, make sure the shade has been
stopped for at least three seconds before pressing the STOP/FAVORITE
button.
Setting
Button
Up
Down
Stop/Favorite
ADJUST MOTOR LIMITS (IF DESIRED)
Setting
Button
e upper and lower limits have been set at the factory. If you need to make
adjustments to the limits, follow the instructions below.
Press the SETTING button on the back of the wand and hold it in until the
motor stops beeping. is will clear both the upper and lower factory limits
as well as a favorite if one was set.
Set Upper Limit - Press the UP button to get the shade close to the desired
upper limit and then press the STOP button to stop the shade. Tap the UP
or DOWN button to move the shade to the desired position. To save the
location, press the SETTING button until the motor beeps.
Set Lower Limit - Press the DOWN button to get the shade close to the
desired lower limit and then press the STOP button to stop the shade. Tap
the UP or DOWN button to move the shade to the desired position. To save
the location, press the SETTING button until the motor beeps.
Up
Down
Stop/Favorite

7
HOLD DOWN BRACKETS (OPTIONAL)
Optional hold down brackets are mounted with the supplied screws.
With the shade at its proper drop, place the pin in each end cap and mark the
screw holes.
Make sure the pins are level and aligned.
Raise the shade, then screw the hold down bracket into the mounting surface.
Flex the hold downs out to reinsert the bottom rail.
SKEW ADJUSTMENT (IF NECESSARY)
If the shade does not raise evenly, rst make sure the mounting brackets are
mounted level with each other.
If the shade is level and it still skews, roll the shade all the way down. Prepare
a strip of masking tape approximately 5” long.
On the side of the shade opposite of the skewing direction, and as close to
the end of the roller as possible, apply the tape with the sticky side facing the
fabric. e tape should be placed on the back of the roller, out of sight.
Roll the shade up and check for skewing. If the shade is still skewing, add
another strip of tape on top of the rst one. If the shade is now skewing in the
opposite direction, tear o about 1” of tape from the last strip installed.
Place tape at this end

8
CLEANING AND CARE
e Shade fabric is easy to care for. Regular dusting with a feather duster or vacuum cleaner brush is recommended. Most
stains can be blotted with a damp sponge and mild detergent. Before using anything stronger than mild detergent and
lukewarm water, test an unobtrusive corner of the shade. If you have any questions, call your dealer for advice.
TROUBLE SHOOTING
PROBLEM SOLUTION
e motor does not work or runs slowly Recharge battery.
e shade moves the opposite direction of the control
buttons.
Press and hold the SETTING button, then press and hold
the STOP button. Hold both until the motor jogs (approx.
10 seconds).
SHADE REMOVAL
If you need to remove your shade, follow the instructions below.
Partially lower the shade and insert a at head screwdriver as shown.
Twist the screwdriver until the head rail disengages from the bracket.
As you release the brackets, support the head rail to keep it from falling.
For no-head rail simple reverse the installation process.
CHARGING THE MOTOR BATTERY
When the shade begins to operate slower than normal, or only beeps when
you attempt to operate, it is time to charge the battery.
Plug the 8.4v charger into the port on the wand.
Plug the charger into an electrical outlet.
A red light on the charger indicates that the battery is charging.
To fully charge the batteries, allow the batteries to charge for at least 1 hour
aer the light on the charger turns green.
A typical charge cycle can take between 4-6 hours.
Charging
Port

MOTORIZED SHADE
Simplicity with rechargeable motor
Installation & Care Instructions 152709 D
10/4/2017
Roller Shades

1
A few simple tools are required:
- Measuring tape
- Power drill, drill bits
-
1⁄4” Hex head and/or Phillips driver bit
- Pencil
GETTING STARTED
IMPORTANT: e remote control has not been linked to the shades. Install
all shades prior to linking the remote.
Additional fasteners other than those sent with your shade may be required
depending on the mounting surface. Wallboard and plaster require the use of
anchors such as expansion or toggle bolts. Brick, tile or stone need special plugs
and drill bits. Remember to always pre-drill holes in wood to avoid splitting.
1 1⁄4”
Hex Head
Bracket
Screw
Head rail
Extension
and Sidemount
Bracket
(optional)
Spacer
Block
(optional)
Mounting
Bracket
Hold
Down
Bracket
(optional)
PN: CS5402 PN: 20201012 PN: CS1000 PN: CS2000
Mounting
Brackets for
Shades without
head rail
PN: CS1101
PN: CS5002(W or BLK)
CS5008 (W or BLK)
CS5529
CS5530
Depends on size of
shade
Charger
PN: CS5199

2
STEP 1: BRACKET INSTALLATION
Shades are shipped with the required number of brackets for proper installation.
End brackets should be located approximately 3” from either end. Depending
on the width of the shade, additional brackets may be necessary, evenly spaced
between the two end brackets.
Using the installation bracket as a template, measure to the edge of the bracket
and mark the hole locations with a pencil for drilling.
Brackets must be in line and level. Shim brackets on inside mounts if necessary.
e head rail must be level for the shade to operate properly.
Shade Width # of Brackets
Up to 40” 2
>40” - 72” 3
>72”- 84” 4
>84” and up 5
SHADES WITH HEAD RAIL
3” 3”
INSIDE MOUNT
e minimum mounting depth for an inside
mount is 1”.
A minimum of 3 3⁄4”is needed to fully recess the
shade.
Make sure the brackets are level and aligned.
Attach using two screws.
Inside Mount
Shallow Mount - Minimum 1” surface
Flush Mount - Minimum 3 3⁄4” surface
1”
Important: If a solar recharge unit is being installed read the section on solar
recharge on page 20 prior to installing mounting brackets.

3
OUTSIDE MOUNT
e minimum mounting height for outside
mounted shades is 1”.
Make sure the brackets are level and aligned.
Attach using two screws.
Outside Mount
Minimum 1” surface
1”
SPACER BLOCKS (OPTIONAL)
Each spacer block projects brackets 3⁄8”away from
mounting surface.
Make sure the brackets are level and aligned.
Attach using two screws. Screws should be long
enough to secure the bracket to the mounting
surface.
Outside Mount with Spacer
Blocks
Optional extension brackets are used to
project the back of the shade up to 2 1⁄2”
from the mounting surface.
Attach the mounting bracket to the
extension bracket with the nut and bolt
provided.
Outside Mount with Extension
Brackets
Minimum 2” surface
2”
2 1⁄2”
EXTENSION BRACKETS (OPTIONAL)
SIDE MOUNT (OPTIONAL)
Measure from window sill up to desired
mounting position on each side of the
window frame. Mark position.
Mount side mount brackets on each side
of window frame as shown. Make sure
to conrm the head rail will sit perfectly
level.
Side Mount
Minimum 2” surface
2”
Once side mount brackets are installed and properly positioned, attach the
mounting brackets using the nuts and bolts provided.

4
Idler Side Bracket Motor Side bracket
Foot
T-Hook
e installation brackets are always mounted
so that the inner surfaces face each other.
Brackets must be in line and level. Shim
brackets on inside mounts if necessary. e
head rail must be level for the shade to operate
properly.
SHADES WITH NO HEAD RAIL
Inside Mount
Minimum 1 1⁄2” surface
Outside Mount
Minimum 1 1⁄2” surface
1 1⁄2”
1 1⁄2”
STEP 2: SHADE INSTALLATION
Push the rail back until it
is fully engaged
Center the shade in the window opening and push the head rail into the
mounting brackets as shown.
SHADES WITH HEAD RAIL
Once the brackets are secured and level, the
fabric roll can be inserted. Make sure your
hands are clean to avoid soiling the fabric.
Insert the foot of the motor-side bracket
into the slotted center hole of the motor
end of the fabric roll. e wire should be
positioned so that it goes up on an inside
mount or back on an outside mount. is
will provide easy access to the setting button.
Nub
Support Bracket
Fig.15
Idler Post
V slot
SHADES WITH NO HEAD RAIL
Set the post of the idler end into the V of the support bracket. Rotate the
T-hook on the support bracket to lock in the post and secure the fabric roll.

5
STEP 3: LINK REMOTE
e remote control has multiple
channels. Before linking the remote,
determine which shade(s) you want on
which channel. e standard remote
has 5 channels, the remote with timer
has 6 channels. All shades linked to
a remote will also automatically be
programmed to the “ALL” channel.
P
Setting
(red button)
Setting
(red button)
Remove plastic lm from the front of the remote.
If battery is not already installed in the remote follow the instructions on page 18.
If using a timer remote, Turn the remote on using the power button on the
right side of the remote. en, tap the clock button until you see “MANUAL”
in the display.
1. Press the SETTING button on the motor until the shade jogs once. Release
the button immediately aer the rst jog - this should not be more than 3
seconds.
2. Repeat this step for all shades that will be controlled by the same channel.
3. Select the channel that you want to program using the CHANNEL selector
button.
4. Press and hold the CONFIRM button until the shade(s) jogs once. e shade
is now linked to the remote.
5. Repeat steps 1-4 to program the rest of the channels.
CH
06:42
MANUAL Power
Button
Up
Stop/Favorite
Down
Channel
Clock
Conrm Limit
Timer Remote
Display
Screen
12345
Channel
Display
Stop/Favorite
Down
Channel +
Channel -
Standard Remote (front)
CL
Conrm
Limit
Standard Remote (back)
Up

6
OPERATION
STANDARD REMOTE
Select the desired channel with the CHANNEL buttons.
e channel indicator light will illuminate the channel
that is on. If all 5 lights are lit, the remote will control all
5 channels at once.
Tapping the UP or DOWN buttons for less than 2
seconds will move the shade in short steps. Holding the
UP or DOWN buttons down for more than 2 seconds
before releasing will operate the shade in the faster
standard speed.
12345
Channel
Display
Up
Stop/Favorite
Down
Channel +
Channel -
Standard Remote (front)
TIMER REMOTE
Shades can be manually operated while in
manual mode. Tap the clock button until
you see “MANUAL” in the display.
Select the desired channel with the
CHANNEL buttons. e channel will
show in the display screen. If all 6 channel
numbers are shown, the remote will control
all 6 channels at once.
Press the UP or DOWN buttons to raise or
lower the shade.
Press the STOP button to stop the shade
anywhere along the travel.
Note: e timer remote does not have ne
adjustment capability.
CH
06:42
MANUAL Power
Button
Up
Stop/Favorite
Down
Channel
Clock
Conrm Limit
Timer Remote
Display
Screen
00:00
MANUAL
Timer Remote Display Screen
Press the UP or DOWN buttons to raise or lower the shade.
Press the STOP button to stop the shade anywhere along the travel.

7
If using a timer remote, tap the clock button until you see “MANUAL” in the
display.
e lower and upper limits have been set at the factory. If you need to make
adjustments to the limits, follow the instructions below.
Please Note: When clearing the factory set limits, both the upper and lower
limits will need to be reset.
Use the CHANNEL buttons to select the channel for the shade that needs to be
adjusted. en follow the directions below.
When adjusting one shade, the other shades on that channel need to be
temporarily unlinked from the remote.
To unlink a shade, press and hold the red SETTING button on the motor until
it completes one jog - jog/jog cycle and then release the SETTING button.
Repeat for all other shades on that channel.
Follow the limit setting instructions below and then relink “turned o ” shades
by following the steps in section 3 LINK REMOTE found on page 5.
ADJUST MOTOR LIMITS (IF DESIRED)
CH
06:42
MANUAL Power
Button
Up
Stop/Favorite
Down
Channel
Clock
Conrm Limit
Timer Remote
Display
Screen
12345
Channel
Display
Stop/Favorite
Down
Channel +
Channel -
Standard Remote (front)
CL
Conrm
Limit
Standard Remote (back)
Up

8
LOWER LIMIT
Hold the LIMIT button until the shade stops jogging.
Use the DOWN button to lower the shade. Press stop when the shade is near the
desired lower limit.
Use the UP and DOWN buttons to adjust the length more accurately.
Hold the CONFIRM button until the shade jogs. is locks in the lower limit.
UPPER LIMIT
Use the UP button to raise the shade. Press stop when the shade is near the
desired upper limit.
Use the UP and DOWN buttons to adjust the upper limit more accurately.
Hold the CONFIRM button until the shade jogs. is locks in the upper limit.
Note: If you also desire to set a favorite position you should do so prior to
relinking other shades on that channel. See the next page for setting favorites.
CH
06:42
MANUAL Power
Button
Up
Stop/Favorite
Down
Channel
Clock
Conrm Limit
Timer Remote
Display
Screen
12345
Channel
Display
Stop/Favorite
Down
Channel +
Channel -
Standard Remote (front)
CL
Conrm
Limit
Standard Remote (back)
Up

9
FAVORITE POSITION
When adding a favorite position
to one shade, the other shades on
that channel need to be temporarily
unlinked from the remote.
To unlink a shade, press and hold the
SETTING button until it completes
one jog - jog/jog cycle and then
release the SETTING button. Repeat
for all other shades on that channel.
SETTING A FAVORITE POSITION
Use the UP or DOWN buttons to position the shade at the desired “favorite”
position. While holding the LIMIT button, quickly press and hold the UP
button. Release both buttons when the shade jogs.
When complete, relink “turned o” shades by following the steps in section 3
LINK REMOTE found on page 5.
USING A FAVORITE POSITION
With the shade at either the upper or lower limit, simply press the STOP/
FAVORITE button to bring the shade to the “favorite” position. To go to the
“favorite” position from any other location, make sure the shade has been
stopped for at least three seconds before pressing the STOP/FAVORITE button.
P
Setting
(red button)
Setting
(red button)
CH
06:42
MANUAL Power
Button
Up
Stop/Favorite
Down
Channel
Clock
Conrm Limit
Timer Remote
Display
Screen
12345
Channel
Display
Stop/Favorite
Down
Channel +
Channel -
Standard Remote (front)
CL
Conrm
Limit
Standard Remote (back)
Up

10
CHANGING A FAVORITE POSITION
Unlink all other shades on the same channel before changing/erasing the favorite
position.
Use the UP or DOWN buttons to position the shade at the desired “favorite”
position. While holding the LIMIT button, quickly press and hold the UP
button. Release both buttons when the shade jogs.
To erase a “favorite” position, bring the shade to the upper limit. Press and hold
the LIMIT button on the back of the remote, then press and hold the UP button.
Release both buttons when the shade jogs.
CH
06:42
MANUAL Power
Button
Up
Stop/Favorite
Down
Channel
Clock
Conrm Limit
Timer Remote
Display
Screen
12345
Channel
Display
Stop/Favorite
Down
Channel +
Channel -
Standard Remote (front)
CL
Conrm
Limit
Standard Remote (back)
Up

11
1. Press the SETTING button on the
motor until the shade jogs once. Release
the button immediately aer the rst jog -
this should not be more than 3 seconds.
ADVANCED PROGRAMMING
P
Setting
(red button)
Setting
(red button)
2. Repeat this step for all shades that will be controlled by a single channel.
3. Select the channel that you want to program using the CHANNEL selector
button.
4. Press and hold the CONFIRM button until the shade(s) jogs once.
5. Repeat steps 1-4 to program the rest of the channels on a multi-channel
remote.
REPLACE ORIGINAL REMOTE, ADD ADDITIONAL
REMOTE OR ADD SHADE TO AN ADDITIONAL CHANNEL
CH
06:42
MANUAL Power
Button
Up
Stop/Favorite
Down
Channel
Clock
Conrm Limit
Timer Remote
Display
Screen
12345
Channel
Display
Stop/Favorite
Down
Channel +
Channel -
Standard Remote (front)
CL
Conrm
Limit
Standard Remote (back)
Up