HunterDouglas RB 500 User manual

Sonesse 30 RTS and Sonesse 30 WireFree (li-ion) RTS with
Standard+ and Heavy Duty+ Brackets
Motorized Shade Installation Series
STANDARD+ BRACKETS
STANDARD+ BRACKET HEAVY DUTY+ BRACKET
HEAVY DUTY+ BRACKETS
© 2018 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or their respective owners.
Las Vegas • Chicago
800.229.5300
HDhospitality.com
1 of 3
a
c
b
d
ac
b
d
OPTIONAL: INTEGRATED LEVELER
ADJUST LEVELER
TOOLS NEEDED
INSTALLING THE BRACKETS
Pencil Level
Measuring
Tape Drill with
bits
Allen Key
(provided with
optional Leveler)
Screwdriver Pliers
Ensure the leveling set screw
opening is pointing downwards
before installing the bracket.
On the Standard+ Bracket, the
orientation can be changed by
loosening the two screws (M3x6)
and turning the leveler 90°. Fix
the screws after turning.
Mount into wood or metal studs or into concrete with concrete anchors. Drywall anchors are not
recommended.
Determine the mounting location.
a) surface/wall b) ceiling c) on frame d) in recess
Measure and mark the bracket locations with a pencil.
Mount brackets with the screws provided.
Pre-drilling is recommended.
Check that the brackets are level and aligned.
Insert the provided Allen key into the set
screw of the leveler.
Adjust skewing by turning the Allen key left
or right to move the shade up or down.
Support the shade with your hand if
necessary.
All adjustments can be made after the shade
has been installed and after the operation has
been tested.
041019

HEAVY DUTY+ BRACKET SCREW COVERS
LOCK THE SHADE
2
1
SCREW COVER INSTALLATION
2 of 3
INSTALLING THE SHADE - Do not remove the tape around the shade until it is fully installed
CHECK SHADE
OPERATION
© 2018 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or their respective owners.
Las Vegas • Chicago
800.229.5300
HDhospitality.com
MOTOR BRACKET IDLE BRACKET
UNLOCKED LOCKED
MOTORS
Sonesse 30 RTS (Plug-In Only)
24V DC
Sonesse 30 WireFree (li-ion) RTS
(Rechargeable Battery)
24V DC
Motor Antenna
Power Cable
Slide the
screw cover
over the
bracket until
it snaps in
place.
Place the motor onto the
motor bracket.
Push the shade against
the motor end and lift
the roller shade up until
the end plug fits into the
center of the idle
bracket.
Rotate the nut on the
idle end clockwise
until it meets the tube.
This locks the shade
into position.
Remove the tape from the shade.
Make sure the shade operates properly. Use separate
wiring information per motor type and programing
instructions from HDhospitality.com
Adjust leveler if applicable.
Sonesse 30 RTS and Sonesse 30 WireFree (li-ion) RTS with
Standard+ and Heavy Duty+ Brackets
Motorized Shade Installation Series

click
click
Slide the end caps onto
the brackets. Snap the end caps onto the brackets until it clicks into
place. Slide the end cap towards you
to remove from the bracket.
Lift the backside of the endcap away from the bracket,
then slide the end cap towards you.
BRACKET COVER INSTALLATION
3 of 3
BRACKET COVER REMOVAL
SHADE REMOVAL
UNLOCK THE SHADE REMOVE IDLE END
STANDARD+ END CAPS HEAVY DUTY+ END CAPS
© 2018 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or their respective owners.
Las Vegas • Chicago
800.229.5300
HDhospitality.com
STANDARD+ BRACKET HEAVY DUTY+ BRACKET
Rotate the nut
on the idle end
counterclockwise
to unlock the
shade.
Slide a flat head
screwdriver between
the idle end plug and
bracket and push
towards the motor
end to remove the
plug from the bracket.
2
1
3
REMOVE CLUTCH END
Move the shade
downward and out
of the motor bracket.
DISCONNECT THE MOTOR
Disconnect the power cable from the
electrical source.
Plug-in: Unplug from the outlet
Sonesse 30 RTS and Sonesse 30 WireFree (li-ion) RTS with
Standard+ and Heavy Duty+ Brackets
Motorized Shade Installation Series