SelectBlinds Odysee User manual

BEFORE INSTALLING THE SHADE YOU MUST REMOVE THE
SHADE FROM THE PACKAGING.
Cut the tie wraps with scissors, do NOT use a knife. Open the
top of the cardboard clamps and remove the shade.
Remove the bracket from the
headrail. Using a cloth-covered, flat
blade screwdriver, push up on the
front tab of the mounting bracket to
release the front of the headrail.
Rotate the headrail downward and
out from the bracket.
BASICS
A few simple tools are required:
- Measuring tape
- Power drill, drill bits
- Hex head and/or Phillips driver bit
- Pencil
Additional fasteners other than those sent with your shade may be
required depending on the mounting surface. Wallboard and plaster
require the use of anchors such as expansion or toggle bolts. Brick,
tile or stone need special plugs and drill bits. Remember to always
pre-drill holes in wood to avoid splitting.
BRACKET INSTALLATION
BRACKET PLACEMENT
Note: Measure and mark all bracket locations before installing.
• Bracket placement is the same for inside and outside mounts.
• Measure 2" in from the ends of the headrail and mark the bracket
location on the mounting surface.
• Space additional brackets evenly between the end brackets.
• Adjust the bracket placement to accommodate obstructions to the
bottom rail, such as window cranks or handles.
INSIDE MOUNT APPLICATIONS
• Align the tops of each installation bracket to the top of the window
opening and attach using two screws per bracket.
• The minimum mounting depth for an inside mount is 1".
• A minimum of 2 5/8" is needed to
fully recess the shade.
•Align the brackets to the inside of the
mark on the mounting surface.
• Adjust the bracket placement to
accommodate obstructions to the
bottom rail, such as a window crank or
handle.
• Use a carpenter’s level to check that
the brackets are level and aligned.
Attach using two screws.
OUTSIDE MOUNT APPLICATIONS
• Attach the back of each installation
bracket using two screws per bracket.
•Align the brackets to the inside of the
mark on the mounting surface.
• The minimum mounting height for
outside-mounted shades is 1".
• Use a carpenter’s level to check that
the brackets are level and aligned.
SPACER BLOCKS (OPTIONAL)
Each spacer block projects brackets
1/2" away from the mounting surface.
• Mount spacer blocks with the solid
side facing the mounting surface.
• Use two mounting screws. Screws
should be long enough to secure the
bracket to the mounting surface.
• Use a maximum of three spacer
blocks per bracket.
EXTENSION BRACKETS (OPTIONAL)
Extension brackets project installation brackets up to 3" away from
the mounting surface. This provides additional clearance for
obstructions such as window cranks or handles.
• Use a carpenter’s level to check that
the extension brackets are level and
aligned. Attach using two screws.
• Attach the installation brackets to the
underside of the extension brackets
using the provided screws and nuts.
SIDE MOUNT APPLICATIONS
Side mount the headrail when conventional mounting
techniques will not work, for example, in an arched
window opening.
The maximum width of a side mounted shade is 48".
• Mount the extension brackets on a surface at least
1 1/2" wide, as shown.
• Attach the installation brackets to the underside of
the extension brackets using the provided screws
and nuts.
INSTALL THE SHADE
Note: Do not remove the low tack protective tape from the face of
the headrail until after the headrail is installed.
• With the colored side of the shade facing you, insert the headrail at
an angle so the back tab on the bracket fits into the back groove on
the headrail.
• Rotate upward to snap into place.
OPERATE THE SHADE
Raising the Shade
• To raise the shade, pull on the front of the cord loop.
Expanding the Vanes
• Pulling on the front of the cord loop at any time will
also expand the vanes, blocking view through the
shade.
Lowering the Shade
• To lower the shades, pull on the rear of the cord loop.
Compressing the Vanes
• Pulling on the rear of the cord loop at any time will
also compress the vanes, permitting view through the
shade.
Tip: If at any time the vanes do not open and close uniformly, “toggle”
the cord loop by alternately pulling on the front and back cords in
rapid succession.
Shade Width # of Brackets
<= 38” 2
38” >= 72” 3
72” >= 106” 4
> 106” 6
Mounting
Bracket Hex Head
Screw Extension Bracket Spacer Block Hold Down Bracket
2” 2”Space Evenly Space Evenly
2”
Spacer
Blocks
1” Minimum
2 5/8” Flush Mount
1” Minimum
1 1/2” Minimum
Width
Extension
Bracket
Front of
Shade
NOTE: Brackets are mounted with the flat part up.
Front of
Bracket
Front of
Bracket
Front of
Bracket
Front of
Bracket
Front of
Bracket
Front of
Bracket

HOLD-DOWN BRACKETS (OPTIONAL)
• Lower the shade with the vanes fully
expanded and place the pins from the
hold-down brackets into the bottom
rail end caps.
• Position the pin at the TOPof the slot
and then mark the bracket hole
location.
• Check that the brackets are level
and aligned. Attach using two screws.
REMOVE THE SHADE
• Using a cloth-covered, flat blade
screwdriver, push up on the front tab
of the mounting bracket to release
the front of the headrail.
• Rotate the headrail downward and
out from the bracket.
CARE AND CLEANING
Convertible shades are made of an anti-static, dust-resistant fabric
which repels dirt and dust. The following options are available if your
shade needs cleaning.
Dusting
Regular light dusting with a feather duster is all the cleaning that is
needed in most circumstances.
Vacuuming
Use a hand-held vacuum with low suction for more
thorough dust removal.
Spot-Cleaning
• Prepare a solution of warm water and mild dishwashing detergent.
• Dampen a clean cloth in the solution and wring it out.
• Dab the spot with the dampened cloth until the spot is gone. Do not
rub the fabric fabric.
• Allow the shade to dry in the completely lowered and expanded
position.
Ultrasonic Cleaning
Convertible shades, except those made with light-dimming fabrics,
can be ultrasonically cleaned by a professional.
• Specify that a mild detergent solution be used.
• Never immerse the headrail in the solution.
• Allow the shade to dry in the completely lowered and expanded
position.
Injection/Extraction
Convertible shades can be professionally cleaned using the
injection/extraction method (On-Site cleaning).
• A dry method of injection/extraction is required for light dimming
fabrics.
CHILD SAFETY
Install Tension Device
The tension device reduces the hazards of strangulation and
entanglement of young children by limiting access to the control cord.
Anchor the Tension Device that is attached to the blind’s control cord,
to the window frame or wall, so that young children cannot pull the
cords around their necks.
A. Lower the blind.
B. Hold the Tension Device upright and position the device using one
of the three methods shown.
C. Position the Tension Device so that the Tension Device and the
control cord do not interfere with raising or lowering the blind. The
Tension device should be installed without stretching or pulling down
on the control cord. Stretching the cord will cause excessive wear. Do
not twist or cross the control cord.
TROUBLESHOOTING
Installation Instructions
OdyseeTM Insulating
Blinds with Continuous
Cordloop Hardware
Our window fashions represent a design breakthrough in style,
efficiency and function. The unique hardware system is
designed to provide years of reliable service when properly
installed.
Please take a few minutes to read through
these instructions before beginning.
Front of
Shade
PROBLEM
One or several vanes are
pushed in (concaved).
The lift cords appear
loose or wavy.
The shade is fully
lowered, but the vanes
seem to hang unevenly.
SOLUTION
Use your hands to
manually push the vane
out.
Operate the cord loop
until any slack is taken
up, and the cords appear
taut. The ‘wavy’ lines
should disappear.
If the vanes do not open
and close uniformly,
“toggle” the cord loop by
alternately pulling on the
front and back cords in
rapid succession.
Collapsed
Cell
Toggle Cord
Alternately
Concaved
Cells Push Out
Concaved Cells
With Your Finger
152077 7/1/08Rev. C