DXV Fresno D35403350 User manual

- 1 -
INSTALLATION INSTRUCTIONS
SAVE FOR FUTURE USE
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017
In the United States:
DXV
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
Thank you for selecting DXV. To ensure that your installation
proceeds smoothly, please read these instructions carefully
before you begin.
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing,
supply stores. It is essential that the tools and materials be on hand before work is begun.
M965558 Rev. 1.4 (4/17)
Model D35403350
Fresno®
Single Control
Semi-Professional Kitchen Faucet
ROUGHING-IN DIMENSIONS:
• For reference
Plumbers' Putty or CaulkingChannel Locks
Phillips Screwdriver
Flat Blade Screwdriver Adjustable Wrench
21-1/2"
(547 mm)
6"
(154 mm)
5-3/4"
(146 mm)
8-1/4"
(209 mm)
27-1/2"
(700 mm)
2" MAX.
(51 mm)
1-3/8" to 1-1/2" DIA.
(35 to 38 mm)
MOUNTING HOLE

- 2 -
2
3
MAKE WATER SUPPLY CONNECTIONS
TEST INSTALLED FAUCET
• Turn off hot and cold water supplies before beginning.
• Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies.
Connection on tting supplies are 3/8" (10 mm) compression.
Connect left supply (Marked with a Red Stripe) to Hot and right
supply (Marked with Blue Stripe) to Cold wall supply. Use
adjustable wrench to tighten connections. Do not over tighten.
• Faucet supplies are 27-1/2" (699 mm) long from faucet base.
Note: If additional supply length is required, installer must
purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are too long, loop as
illustrated to avoid kinking.
M965558 Rev. 1.4 (4/17)
1INSTALL FITTING
CAUTION Turn off hot and cold wate
supplies before beginning.
• Make certain the O-RING SEAL (1) is properly seated in recess of faucet body.
• Insert supply HOSES (2) and SHANK (3) through center hole of sink or
mounting surface.
• Assemble RUBBER WASHER (4), PLASTIC WASHER (5), METAL WASHER (6) and
threaded LOCKNUT (7) onto SHANK (3) from underside of sink or mounting surface.
Hand tighten LOCKNUT (7) and check that faucet is centered.
• Use a screwdriver to tighten SCREWS (8) on LOCKNUT (7). Work your way around
LOCKNUT (7), tightening the screws slightly each time until all are snug to ensure
even pressure.
1
2
5
RECESS
4
3
6
7
8
RED
STRIPE
BLUE
STRIPE
1
2
COLD
HOT
• Move HANDLE (1) into “off” position.
• Unthread SPRAY END (2) from HOSE END (3).
• Turn on water supplies and check connections
for leaks.
• Operate HANDLE (1) on and off, hot and cold to ush
water lines thoroughly. Replace SPRAY END (2).
• Check all drain connections for leaks.
• Move HANDLE (1) into “off” position.
1
2
3
HOT & COLD SUPPLIES

- 3 -
3SERVICE
SERVICE
• Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, rst turn off water supply then:
• Loosen and remove LEVER HANDLE (1). Loosen
HANDLE SCREW (2) with 2.5 mm Hex Wrench
and then pull HANDLE BASE (3) off.
• Unscrew ESCUTCHEON CAP (4). Unscrew
the CARTRIDGE NUT (5).
• Remove CARTRIDGE (6). Clean inlets of
CARTRIDGE (6) and MANIFOLD (7).
• Reassemble CARTRIDGE (6). Replace CARTRIDGE
NUT (5), CAP (4) and HANDLE assembly, check ow.
•If SPOUT (3) leaks at swivel point the O-RINGS (2)
need to be replaced. To remove SPOUT (3):
• Loosen the SPOUT SET SCREW (1) with
a 3mm Hex wrench.
• Rotate the SPOUT (3) side to side while pulling
upward to remove SPOUT (3) from faucet body.
• Replace the defective parts, grease O-RINGS
then push SPOUT (3) back into position.
Tighten SET SCREW (1).
• Check that SPOUT (3) rotates freely and
does not leak at the swivel point.
5
4
M965558 Rev. 1.4 (4/17)
2
3
1
4
5
6
7
CLEAN
3
1
REMOVE
INSTALL
3mm HEX
WRENCH
2

- 4 -
MODEL NUMBER
D35403350
Fresno®
Single Control Semi-Professional
Kitchen Faucet
M965558 Rev. 1.4 (4/17)
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 100
ULTRA STEEL 355
M962672-0070A
MOUNTING KIT
M962690-0070A
CARTRIDGE NUT
M962652-0070A
SPOUT SET
SCREW M962691-YYY0A
CARTRIDGE COVER
M906667-0070A
FIXATION RING
M964407-0070A
CARTRIDGE
M964722-YYY0A
HANDLE KIT
M962701-0070A
O-RING
M964341-0070A
SPOUT BUSHING
& O-RING KIT
M962695-YYY0A
SPRAY HOSE
AND SEALS
M962696-0070A
CHECK VALVE
M962683-YYY0A
PULL-DOWN SPRAY
WITH CHECK VALVE
M962697-YYY0A
SPRAY HOSE ADAPTER
M962694-YYY0A
SPOUT SPRING
M962702-YYY0A
SPOUT PIPE
M962698-0070A
SEAL
M962699-YYY0A
SPRAY ARM
M962700-0070A
SPRAY ARM BUSHING
M964725-YYY0A
PEDESTAL
M921935-0070A
ADAPTOR