SEW-Eurodrive BMV User manual

*28520270_1218*
Drive Technology \ Drive Automation \ System Integration \ Services
Operating Instructions
Didactics – Electromechanics
Brake Control Module (BMV)
Edition 12/2018 28520270/EN

SEW-EURODRIVE—Driving the world

Table of contents
Operating Instructions – Brake Control Module (BMV) 3
Table of contents
1 General information.................................................................................................................. 5
1.1 About this documentation ...............................................................................................5
1.2 Structure of the safety notes ...........................................................................................5
1.3 Decimal separator in numerical values ...........................................................................6
1.4 Rights to claim under limited warranty ............................................................................6
1.5 Other applicable documentation .....................................................................................6
1.6 Product names and trademarks......................................................................................6
1.7 Copyright notice ..............................................................................................................6
2 Safety notes .............................................................................................................................. 7
2.1 Preliminary information ...................................................................................................7
2.2 Target group ...................................................................................................................7
2.3 Designated use ...............................................................................................................7
2.4 Transport.........................................................................................................................8
2.5 Setup and installation......................................................................................................8
2.6 Electrical connection .......................................................................................................8
2.7 Startup and operation .....................................................................................................9
2.8 Inspection and maintenance ...........................................................................................9
3 Device structure ..................................................................................................................... 10
3.1 Scope of delivery ..........................................................................................................10
3.2 Basic unit ......................................................................................................................10
4 Installation............................................................................................................................... 11
4.1 Important information ....................................................................................................11
4.2 Electrical connections ...................................................................................................12
4.3 Connection to CM.. servomotor ....................................................................................14
4.4 Connection to DR.. ACmotor .......................................................................................17
4.5 Wiring diagram..............................................................................................................17
5 Startup ..................................................................................................................................... 18
5.1 With MOVITRAC®B frequency inverter module ..........................................................18
5.2 With MOVIDRIVE®B drive inverter module .................................................................19
5.3 Startup with other modules ...........................................................................................20
5.4 Checking the connection of the brake...........................................................................20
5.5 Operating principle of BMV brake control .....................................................................20
6 Operation................................................................................................................................. 21
6.1 Important information ....................................................................................................21
6.2 Operating and controlling the brake..............................................................................21
7 Service..................................................................................................................................... 23
7.1 Electronics Service by SEW‑EURODRIVE...................................................................23
7.2 Waste disposal..............................................................................................................23
8 Technical data......................................................................................................................... 24
9 Standards and certifications ................................................................................................. 25
9.1 EC declaration of conformity.........................................................................................25
28520270/EN – 12/2018

Table of contents
Operating Instructions – Brake Control Module (BMV)
4
9.2 Certifications .................................................................................................................25
10 Address list ............................................................................................................................. 26
Index ........................................................................................................................................ 27
28520270/EN – 12/2018

1
General information
About this documentation
Operating Instructions – Brake Control Module (BMV) 5
1 General information
1.1 About this documentation
The current version of the documentation is the original.
This documentation is an integral part of the product. The documentation is intended
for all employees who perform work on the product.
Make sure this documentation is accessible and legible. Ensure that persons respons-
ible for the systems and their operation as well as persons who work on the product
independently have read through the documentation carefully and understood it. If you
are unclear about any of the information in this documentation, or if you require further
information, contact SEW‑EURODRIVE.
1.2 Structure of the safety notes
1.2.1 Meaning of signal words
The following table shows the grading and meaning of the signal words for safety
notes.
Signal word Meaning Consequences if disregarded
DANGER Imminent hazard Severe or fatal injuries
WARNING Possible dangerous situation Severe or fatal injuries
CAUTION Possible dangerous situation Minor injuries
NOTICE Possible damage to property Damage to the product or its envi-
ronment
INFORMATION Useful information or tip: Simplifies
handling of the product.
1.2.2 Structure of section-related safety notes
Section-related safety notes do not apply to a specific action but to several actions
pertaining to one subject. The hazard symbols used either indicate a general hazard
or a specific hazard.
This is the formal structure of a safety note for a specific section:
SIGNAL WORD
Type and source of hazard.
Possible consequence(s) if disregarded.
• Measure(s) to prevent the hazard.
Meaning of the hazard symbols
The hazard symbols in the safety notes have the following meaning:
Hazard symbol Meaning
General hazard
28520270/EN – 12/2018

1General information
Decimal separator in numerical values
Operating Instructions – Brake Control Module (BMV)
6
Hazard symbol Meaning
Warning of dangerous electrical voltage
Warning of hot surfaces
1.2.3 Structure of embedded safety notes
Embedded safety notes are directly integrated into the instructions just before the de-
scription of the dangerous action.
This is the formal structure of an embedded safety note:
SIGNAL WORD Type and source of hazard. Possible consequence(s) if disregar-
ded. Measure(s) to prevent the hazard.
1.3 Decimal separator in numerical values
In this document, a period is used to indicate the decimal separator.
Example: 30.5kg
1.4 Rights to claim under limited warranty
Read the information in this documentation. This is essential for fault-free operation
and fulfillment of any rights to claim under limited warranty. Read the documentation
before you start working with the product.
1.5 Other applicable documentation
Observe the corresponding documentation for all further components.
1.6 Product names and trademarks
The brands and product names in this documentation are trademarks or registered
trademarks of their respective titleholders.
1.7 Copyright notice
©2018SEW‑EURODRIVE. All rights reserved. Unauthorized reproduction, modifica-
tion, distribution or any other use of the whole or any part of this documentation is
strictly prohibited.
28520270/EN – 12/2018

2
Safety notes
Preliminary information
Operating Instructions – Brake Control Module (BMV) 7
2 Safety notes
2.1 Preliminary information
The following general safety notes serve the purpose of preventing injury to persons
and damage to property. They primarily apply to the use of products described in this
documentation. If you use additional components, also observe the relevant warning
and safety notes.
2.2 Target group
The product is intended for persons in training facilities that are equipped with the ap-
propriate furnishings in classrooms and laboratories. Furnishings are, for example, ex-
perimental stands, laboratory benches, energy cells, control panels and control con-
soles as well as control cabinets with pick-up positions for electrical energy.
The focus is on the transfer of knowledge to non-specialists. Before using the
products, non-specialists must be instructed about the safety-relevant aspects des-
cribed in this document.
Specialist for me-
chanical work
Any mechanical work on the products must be carried out by a qualified specialist.
Specialists in the context of this documentation are persons familiar with the design,
mechanical installation, troubleshooting, and maintenance of the product who possess
the following qualifications:
• Qualification in the field of mechanical engineering in accordance with the national
regulations.
• They are familiar with this documentation.
Specialist for elec-
trotechnical work
Any electrical work on the products must be carried out by adequately qualified electri-
cians. Qualified electricians in the context of this documentation are persons familiar
with electrical installation, startup, troubleshooting, and maintenance of the product
who possess the following qualifications:
• Qualification in the field of electrical engineering in accordance with the national
regulations.
• They are familiar with this documentation.
Additional qualifi-
cation
In addition to that, these persons must be familiar with the valid safety regulations and
laws, as well as with the requirements of the standards, directives, and laws specified
in this documentation. The persons must have the express authorization of the com-
pany to operate, program, parameterize, label, and ground units, systems, and circuits
in accordance with the standards of safety technology.
Instructed persons All work in the areas of transportation, storage, operation and waste disposal must be
carried out by persons who are trained appropriately. The purpose of the instruction is
that the persons are capable of performing the required tasks and work steps in a safe
and correct manner.
2.3 Designated use
The product is designed for training purposes only. Operating the product in private,
craft, trade or for industrial purposes is not permitted. The product is not intended for
installation in electrical plants or machines. The product is not intended for use in ap-
plications (such as lifting applications).
The product can be used to operate ACasynchronous motors and synchronous ser-
vomotors with squirrel-cage rotor.
28520270/EN – 12/2018

2Safety notes
Transport
Operating Instructions – Brake Control Module (BMV)
8
Startup (i.e. start of regular operation) is permitted with adherence to EMC guideline
only.
Technical data and information on the connection conditions are provided on the
nameplate and in the documentation. Comply with the data and conditions.
2.4 Transport
Inspect the shipment for damage as soon as you receive the delivery. Inform the ship-
ping company immediately about any damage. If the product is damaged, it must not
be assembled, installed or started up.
Observe the following notes when transporting the device:
• Before transportation, cover the connections with the supplied protection caps.
• Place the product only on the base plate during transport.
• Ensure that the product is not subject to mechanical impact.
If necessary, use suitable, sufficiently dimensioned handling equipment.
2.5 Setup and installation
Ensure that the product is installed and cooled according to the regulations in the doc-
umentation.
The product is suited for operation on laboratory benches and on tables. Use standard
laboratory or training equipment where the products can be placed properly and safely
without posing any risk to the learners.
Protect the product from strong mechanical strain. The product and its mounting parts
must never protrude into the path of persons or vehicles. Ensure that components are
not deformed and insulation spaces are not changed, particularly during transportation
and handling. Electric components must not be mechanically damaged or destroyed.
The following applications are prohibited unless the device is explicitly designed for
such use:
• Use in potentially explosive atmospheres
• Use in areas exposed to harmful oils, acids, gases, vapors, dust, and radiation
• Operation in applications with impermissibly high mechanical vibration and shock
loads in excess of the regulations stipulated in EN61800-5-1
• Use at an elevation of more than 4000m above sea level
2.6 Electrical connection
Familiarize yourself with the applicable national accident prevention regulations before
working on the product.
Perform electrical installation according to the pertinent regulations (e.g. cable cross-
sections, fusing, protective conductor connection).
Ensure that all of the required covers are correctly attached after the electrical installa-
tion.
The preventive measures and protection devices must comply with the applicable reg-
ulations (e.g. EN60204-1 or EN61800-5-1).
28520270/EN – 12/2018

2
Safety notes
Startup and operation
Operating Instructions – Brake Control Module (BMV) 9
Ground connections are required as preventive measures.
2.7 Startup and operation
Before startup, make sure that the 4mm sockets, buttons, and switches are intact.
It might be necessary to equip locations where such devices are used with additional
monitoring and protection devices in accordance with the respective applicable safety
regulations, e.g. the law governing technical equipment, accident prevention regula-
tions, etc.
Depending on the degree of protection, products may have live, uninsulated, and
sometimes moving or rotating parts, as well as hot surfaces during operation.
Cover unused connections with the supplied protection caps during operation.
Make sure the connection boxes are closed and screwed before connecting the sup-
ply voltage.
When the device is switched on, dangerous voltages are present at all power connec-
tions as well as at any connected cables and terminals. This also applies even when
the product is inhibited and the motor is at standstill.
Electric shock due to moving the device while voltage is applied. Do not move the
product while voltage is applied.
Do not separate the connection to the product during operation. This may result in
dangerous electric arcs damaging the product.
If you disconnect the product from the voltage supply, do not touch any live compon-
ents or power connections because capacitors might still be charged. Observe the fol-
lowing minimum switch-off time:
10 minutes.
Observe the corresponding information signs on the product.
The fact that the operation LED and other display elements are no longer illuminated
does not indicate that the product has been disconnected from the supply system and
no longer carries any voltage.
Mechanical blocking or internal protective functions of the product can cause a motor
standstill. Eliminating the cause of the problem or performing a reset may result in the
drive restarting automatically. If, for safety reasons, this is not permitted for the drive-
controlled machine, first disconnect the product from the supply system and then start
troubleshooting.
2.8 Inspection and maintenance
Only perform maintenance and repair work once the product has been secured and
disconnected from the power supply. Ensure a de-energized state of the product be-
fore you start working on it. Ensure a de-energized state for the entire time you work
on the product.
Repair work may only be carried out by SEW‑EURODRIVE.
28520270/EN – 12/2018

3Device structure
Scope of delivery
Operating Instructions – Brake Control Module (BMV)
10
3 Device structure
3.1 Scope of delivery
The following components are included in the delivery:
• Pasted and assembled front plate
• Housing
• Brake control BMV5
(brake control unit with electronic switching, DC24V control input and rapid cut-
off)
• Protection cover for brake control
3.2 Basic unit
1
2
3
4
13
14
15
BM. ...
1
3
4
13
14
15
13 14 15
!
+24V DC
0V DC
+24V DC
U IN
+24V DC
U IN
0V DC
PE
2
[1]
[2]
[4]
[3]
[5]
[6]
Brake control module (BMV)
Brake
connection
Brake
Applied
ReleasedInverter
9007217489840139
[1] Brake control unit BMV5 [4] Selector switches
[2] Brake connection [5] Control voltage/control signal UIN DC24V
[3] PE: PE connection [6] Voltage supply DC24V (brake voltage)
28520270/EN – 12/2018

4
Installation
Important information
Operating Instructions – Brake Control Module (BMV) 11
4 Installation
4.1 Important information
INFORMATION
• Observe the documentation of components connected or mounted to the module
(e.g. motor, inverter).
• Comply with all instructions referring to the technical data and the permissible
conditions where the device is operated.
WARNING
Electric shock when disconnecting or connecting voltage-carrying plug connectors.
Severe or fatal injuries.
• Disconnect all supply voltages.
• Make sure that the device is de-energized.
• Never plug or unplug the plug connectors while they are energized.
CAUTION
Short circuit due to incorrectly set jumpers.
Damage to property and injury.
• Insert the jumpers only in the contact points provided for this purpose.
INFORMATION
Connect only suitable 2‑ and 3‑wire brakes to the device output with appropriate
brake coil voltage (brake voltage).
4.1.1 Brake connection
Only connect suitable brakes. Observe the the brake voltage.
NOTICE
Damage or destruction of the brake resulting from incorrect voltage.
Damage to property.
• Do not connect the brake directly to a supply voltage. Always use a brake control
unit or a brake rectifier.
4.1.2 Cable
Use the following cables:
• Standardized safety cables for use in classrooms or laboratories.
• 4mm laboratory safety plug connectors with rigid insulating sleeve, suited for nom-
inal voltages of up to 1000V.
• Didactics connection cable from SEW‑EURODRIVE.
The cable must not be longer than 3m.
28520270/EN – 12/2018

4Installation
Electrical connections
Operating Instructions – Brake Control Module (BMV)
12
4.1.3 PE line connection according to EN61800‑5‑1
Earth-leakage currents of ≥3.5mA can occur during normal operation. Observe the
following for reliable PE connection:
• Supply system cable <10mm2:
– Second PE conductor with the same cross section as the supply system cable
routed parallel to the protective earth via separate terminals, or
– Copper PE conductor with a cross section of 10mm2
• Supply system cable 10to16mm2:
– Copper protective earth conductor with the same cross section as the supply
system cable.
• Supply system cable 16to35mm2:
– Copper PE conductor with a cross section of 16mm2
• Supply system cable>35mm2:
– Copper PE conductor with half the cross section of the supply system cable.
4.1.4 Interference emission
Use shielded motor cables and brake cables for EMC compliant installation.
4.1.5 Cabling components
You can connect various didactics frequency inverter modules from
SEW‑EURODRIVE to the didactics brake control module using a 4 mm laboratory
cable. SEW‑EURODRIVE recommends to use 4 mm safety tower plugs 1000 V
CATII.
You can connect the motor brake to the brake control unit using 4mm safety tower
plugs 1000 V CAT II. However, SEW‑EURODRIVE recommends to use shielded
brake cables.
4.2 Electrical connections
4.2.1 Brake voltage supply
+24V DC
0V DC
[1]
[2]
18235822603
[1] DC+24V
[2] DC0V (GND)
28520270/EN – 12/2018

4
Installation
Electrical connections
Operating Instructions – Brake Control Module (BMV) 13
4.2.2 Control voltage
+24V DC
U IN
+24V DC
U IN
0V DC
[1]
[2]
[3]
18379814027
[1] Input for control voltage of the inverter
[2] Input for the control voltage/control signal UIN (external)
[3] Ground (GND)
4.2.3 PE connection
PE
18235773707
4.2.4 Brake connection
13 14 15
Brake
connection
18235831051
28520270/EN – 12/2018

4Installation
Connection to CM.. servomotor
Operating Instructions – Brake Control Module (BMV)
14
4.3 Connection to CM.. servomotor
4.3.1 BK brake
The following figure shows the wiring diagram for connection to a CM.. servomotor
with BK brake:
D
C
B
A
3
1
4
BMV
1 2 3 4
13 14
15
SB1
K12
+-
U
DC 24 V
IN
DC 24 V
+-
+-
-
+
19026691595
NOTICE
Damage to the BK brake.
Damage to property.
• Adhere to the specified polarity of the power supply of the BK brake.
• Check the polarity when replacing the brake.
If you use a motor with BK brake, you need terminals 13 and 15.
The following figure shows direct brake supply with 24V:
D
C
B
A
3
1
4
SB1
24 V
DC
- +
12986696203
Protect the brake against overvoltage in the following cases, for example by means of
varistor overvoltage protection:
• When operated on third-party inverters
• When using brakes that are not directly supplied from SEW‑EURODRIVE invert-
ers.
28520270/EN – 12/2018

4
Installation
Connection to CM.. servomotor
Operating Instructions – Brake Control Module (BMV) 15
4.3.2 BP brake
The following figure shows the wiring diagram for connection to a CM.. servomotor
with BP brake:
D
C
B
A
3
1
4
BMV
1 2 3 4
13 14
15
SB1
K12
+-
24 V
DC
24 V
DC
18379737355
If you use a motor with BP brake, you need only terminals 13 and 15.
The following figure shows the terminals on the cable end and on the motor end:
D
C
B
A
3
1
4
BK +
BK
GNYE
BK
BK
1
U
V
W
3BK –
[1]
[3]
D
C
B
A
3
1
4
YE
YE
BU
GNYE
RD
BK
U1
V1
[2]
W1 –
+
[A] [B]
18100985355
[A] Connection on cable end [2] Brake coil
[B] Connection on motor end [3] Motor cable labeling
[1] BP brake
28520270/EN – 12/2018

4Installation
Connection to CM.. servomotor
Operating Instructions – Brake Control Module (BMV)
16
4.3.3 BY brake
The following figure shows the wiring diagram for connection to a CM.. servomotor
with BY brake:
D
C
B
A
3
1
4
BMV
1 2 3 4
13 14
15
SB1
K12
+-
24 V
DC
24 V
DC
9007217355716875
If you use a motor with BY brake, you need terminals 13, 14, and 15.
The following figure shows the terminals on the cable end and on the motor end:
D
C
B
A
3
1
4
BU
GNYE
RD
BK
U1
V1
W1
[2]
RD
BU
WH
D
C
B
A
3
1
4
BK
GNYE
BK
BK U
V
W
3BK
BK
2
13 1
[1]
14
15
BK
[3]
[4]
[A] [B]
18385019915
[A] Connection on cable end [2] Brake coil
[B] Connection on motor end [3] Motor cable labeling
[1] BY brake [4] Designation on BMV brake control
28520270/EN – 12/2018

4
Installation
Connection to DR.. ACmotor
Operating Instructions – Brake Control Module (BMV) 17
4.4 Connection to DR.. ACmotor
The following figure shows the wiring diagram for connection to a DR.. ACmotor with
BE brake:
1a
2a
3a
4a
5a
M
BS
TS
RD
WH
BU
- + - +
1
2
13
14
15
4
3
BMV
DC 24 V
UIN
DC 24 V
18101028747
4.5 Wiring diagram
DC +24 V
DC 0 V
DC +24 V
U in
DC 24 V
PE
PE
U in
DC 0 V
S1
S1
Brake control module DC 24 V
Brake connection
Housing
9007217702210187
28520270/EN – 12/2018

5Startup
With MOVITRAC®B frequency inverter module
Operating Instructions – Brake Control Module (BMV)
18
5 Startup
5.1 With MOVITRAC®B frequency inverter module
With
MOVITRAC
®B
frequency
inverter
module
Wire the didactics modules as shown in the following figure:
MOVITRAC
DI 00 X12.1 DI 01 X12.2 DI 02 X12.3
DI 03 X12.4
DI 04 X12.5
DI 05 X12.6
Vo-TF X12.7
GND X12.9
X12
24V I/O X12.8
CO NO NC
REF 1 X10.1
AI 11 X10.2 AI 12 X10.3
GND X10.4
X10
!
PE
1 2 3 4 13 14 15
1 3 4 13 14 15
13 14 15
2
X13
GND X13.1 DO 02 X13.2 DO 03 X13.3
GND X13.4
DO 01-CO X13.5
DO 01-NO X13.6
DO 01-NC X13.7
-24V DC
0V DC
+24V DC
U IN
+24V DC
U IN
0V DC
-+
PE
PE
PE
1
2
3
4
13
14
15
1
3
4
13
14
15
2
WH
!
BURD
MOVITRAC
DI 00
X12.1
DI 01
X12.2
DI 02
X12.3
DI 03
X12.4
DI 04
X12.5
DI 05
X12.6
Vo-TF
X12.7
GND
X12.9
X12
24V
I
/O
X12.8
CO
NO
NC
REF 1
X10.1
AI 11
X10.2
AI 12
X10.3
GND
X10.4
X10
DO 01-CO
X13.5
DO 01-NO
X13.6
DO 01-NC
X13.7
DC 24 V (external)
Brake
connection
to the motor brake
Brake control module (BMV)
MOVITRAC®B frequency inverter module (MCB)
9007217637527179
28520270/EN – 12/2018

5
Startup
With MOVIDRIVE®B drive inverter module
Operating Instructions – Brake Control Module (BMV) 19
5.2 With MOVIDRIVE®B drive inverter module
With
MOVIDRIVE
®B drive
inverter
module
Wire the didactics modules as shown in the following figure:
-24V DC
0V DC
+24V DC
U IN
+24V DC
U IN
0V DC
!
PE
1 3 4
1 2 3 4 13 14 15
13 14 15
13 14 15
2
- +
PE
PE
PE
PE
1
3
4
1
2
3
4
13
14
15
13
14
15
2
WH
!
BU
RD
DGND
X12:1
SC12
X12:3
SC11
X12:2
X12
SVI24
X17:4
S0V24
X17:3
VO24
X17:2
DGND
X17:1
X17
X10
DGND
X17:9
DGND
X10:2
TF1 X10:1
X11
REF 2 X11:5 AGND X11:4
AGND X11:4 AI 12 X11:3 AI 11 X11:2 REF1 X11:1
VO24
X13:8
X13
DI 06
X16:1
DI 06
X16:2
X16
DI 00
X13:1
DI 01
X13:2
DI 02
X13:3
DI 03
X13:4
DI 04
X13:5
DI 05
X13:6
X13
DGND
X16:6
X16
DO 04 X16:4 DO 05 X16:5 DO 03 X16:3 DB 00 X10:3 DO 01-C X10:4 DO 01-NO X10:5 DO 01-NC X10:6 DO 02 X10:7
X10
CO NO NC
X100 X101
DGND
X12:1
SC12
X12:3
SC11
X12:2
X12
SVI24
X17:4
X17:4
S0V24
X17:3
VO24
X17:2
DGND
X17:1
X17
X10
DGND
X17:9
DGND
X10:2
TF1
X10:1
X11
REF 2
X11:5
AGND
AGND
X11:4
AGND
AGND
AGND
X11:4
X11:4
X11:4
AI 12
X11:3
AI 11
X11:2
REF1
X11:1
VO24
X13:8
X13
DI 06
X16:1
DI 06
X16:2
X16
DI 00
X13:1
DI 01
X13:2
DI 02
X13:3
DI 03
X13:4
DI 04
X13:5
DI 05
X13:6
X13
CO
NO
NC
X100
X101
MOVIDRIVE®B drive inverter module (MDX)
Brake
connection
DC 24 V (external)
Brake control module (BMV)
to the motor brake
9007217639313163
28520270/EN – 12/2018

5Startup
Startup with other modules
Operating Instructions – Brake Control Module (BMV)
20
5.3 Startup with other modules
The brake need not necessarily be released by a frequency inverter.
The "inverter" input can be switched, for example, by a higher-level controller (PLC) or
by other similar modules.
5.4 Checking the connection of the brake
Check for correct connection of the brake to the didactics module.
Check to see which brake type is used:
• 2‑wire brake (BP brake when using synchronous servomotors)
• 3‑wire brake (BY brake when using synchronous servomotors)
• 2- or 3‑wire brake (BE brake when using ACasynchronous motors)
NOTICE
Damage or destruction of the brake resulting from incorrect voltage.
Damage to property.
• Refer to the motor nameplate to check whether the correct brake voltage is used.
Use shielded brake cables.
5.5 Operating principle of BMV brake control
BMV brake control energizes the brake coil if both power supply (according to the
brake voltage 12 to 24 V) and a DC 24 V signal (e.g. from a frequency inverter or
PLC) are present at the same time. The brake is applied if one condition is not being
met.
The ground of the inverter, e.g. X13.1 GND, must be connected with the ground of the
external DC 24 V power supply. Only then can the brake be released (for example
manually) via frequency inverter or higher-level controller.
BMV brake control allows for shortest response and application times.
28520270/EN – 12/2018