SEW-Eurodrive MOVIMOT MM D Series Administrator guide

Drive Technology \ Drive Automation \ System Integration \ Services
Compact Operating Instructions
MOVIMOT
®
MM..D
with AC Motor DT/DV
Edition 11/2009 16885228 / EN

SEW-EURODRIVE—Driving the world

Compact Operating Instructions – MOVIMOT® MM..D with AC Motor DT/DV 3
Contents
Contents
1 General Information ............................................................................................ 4
1.1 Scope of this documentation....................................................................... 4
1.2 Structure of the safety notes ....................................................................... 4
2 Safety Notes ........................................................................................................ 5
2.1 General information .................................................................................... 5
2.2 Target group ............................................................................................... 5
2.3 Designated use ........................................................................................... 5
2.4 Transportation, storage............................................................................... 6
2.5 Installation................................................................................................... 6
2.6 Electrical connection ................................................................................... 6
2.7 Safe disconnection...................................................................................... 7
2.8 Operation .................................................................................................... 7
3 Type Designations .............................................................................................. 8
3.1 Sample motor nameplate............................................................................ 8
3.2 Sample inverter nameplate ......................................................................... 9
3.3 Unit identification......................................................................................... 9
3.4 "Mounting close to the motor" design ....................................................... 10
4 Mechanical Installation..................................................................................... 11
4.1 MOVIMOT®gearmotor ............................................................................. 11
4.2 Installing the MOVIMOT®inverter close to the motor ............................... 13
4.3 Tightening torques .................................................................................... 14
5 Electrical Installation ........................................................................................ 16
5.1 Installation instructions.............................................................................. 16
5.2 Connection of MOVIMOT®........................................................................ 20
5.3 Connection between MOVIMOT®and motor when mounted close to the
motor......................................................................................................... 21
6 Startup................................................................................................................ 24
6.1 Important notes on startup ........................................................................ 24
6.2 Description of the controls ........................................................................ 25
6.3 Description of the DIP switches S1 ........................................................... 28
6.4 Description of DIP switches S2 ................................................................. 30
6.5 Startup with binary control ........................................................................ 33
6.6 Supplementary notes for installation close to the motor .......................... 35
7 Startup with RS-485 Interface/Fieldbus .......................................................... 38
7.1 Important notes on startup ........................................................................ 38
7.2 Startup procedure ..................................................................................... 38
8 Operation ........................................................................................................... 41
8.1 Operating display ...................................................................................... 41
9 Service ............................................................................................................... 42
9.1 Status and error display ............................................................................ 42
9.2 Replacing units ......................................................................................... 45
10 Declaration of Conformity ................................................................................ 46

4Compact Operating Instructions – MOVIMOT® MM..D with AC Motor DT/DV
1Scope of this documentation
General Information
MOVIMOT® MM..D with AC Motor DT/DV
1 General Information
1.1 Scope of this documentation
This documentation contains the general safety notes and selected information
regarding MOVIMOT®MM..D with AC motor DT/DV.
• Please note that this documentation does not replace the detailed operating
instructions.
• Read the detailed operating instructions before you start working with MOVIMOT®
MM..D.
• Observe the information, instructions and notes in the detailed operating instructions
and the "AC Motors DR/DV/DT/DTE/DVE" operating instructions. This is essential for
fault-free operation of MOVIMOT®MM..D and fulfillment of any rights to claim under
guarantee.
• The enclosed CD or DVD contains PDF files of the additional operating instructions
as well as further MOVIMOT®MM..D documentation.
• All SEW-EURODRIVE’s technical documentation is available to download in PDF
format from the SEW-EURODRIVE website: www.sew-eurodrive.de.
1.2 Structure of the safety notes
The safety notes in these operating instructions are structured as follows:
Pictogram SIGNAL WORD
Type and source of danger.
Possible consequence(s) if disregarded.
• Measure(s) to prevent the danger.
Pictogram Signal word Meaning Consequences if disre-
garded
Example:
General danger
Specific danger,
e.g. electric shock
DANGER Imminent danger Severe or fatal injuries
WARNING Possible dangerous situation Severe or fatal injuries
CAUTION Possible dangerous situation Minor injuries
NOTICE Possible damage to property Damage to the drive system or its
environment
INFORMA-
TION
Useful information or tip.
Simplifies the handling of the
drive system.

Compact Operating Instructions – MOVIMOT® MM..D with AC Motor DT/DV 5
2
General information
Safety Notes
2 Safety Notes
The following basic safety notes must be read carefully to prevent injury to persons and
damage to property. The operator must ensure that the basic safety notes are read and
observed. Make sure that persons responsible for the plant and its operation, as well as
persons who work independently on the unit, have read through the operating
instructions carefully and understood them. If you are unclear about any of the
information in this documentation, please contact SEW-EURODRIVE.
2.1 General information
Never install or start up damaged products. Submit a complaint to the shipping company
immediately in the event of damage.
During operation, MOVIMOT®drives can have live, bare and movable or rotating parts
as well as hot surfaces, depending on their enclosure.
Removing covers without authorization, improper use as well as incorrect installation or
operation may result in severe injuries to persons or damage to property. Refer to the
documentation for additional information.
2.2 Target group
Only qualified electricians are authorized to install, startup or service the units or
correct unit faults (observing IEC 60364 or CENELEC HD 384 or DIN VDE 0100 and
IEC 60664 or DIN VDE 0110 as well as national accident prevention guidelines).
Qualified personnel in the context of these basic safety notes are persons familiar with
installation, assembly, startup and operation of the product who possess the necessary
qualifications.
Any activities regarding transportation, storage, operation, and disposal must be carried
out by persons who have been instructed appropriately.
2.3 Designated use
MOVIMOT®drives are components intended for installation in electrical systems or
machines.
In case of installation in machines, startup of MOVIMOT®inverters (i.e. start of
designated operation) is prohibited until it is determined that the machine meets the
requirements stipulated in the EC Directive 2006/42/EC (machine directive).
Startup (i.e. the start of designated use) is only permitted under observance of the EMC
directive 2004/108/EC.
MOVIMOT®inverters comply with the regulations of the Low Voltage Directive 2006/95/
EC. The standards given in the declaration of conformity are used for MOVIMOT®
inverters.
You must observe the technical data and information on the connection requirements
as provided on the nameplate and in the documentation.

6Compact Operating Instructions – MOVIMOT® MM..D with AC Motor DT/DV
2Transportation, storage
Safety Notes
2.3.1 Safety functions
The MOVIMOT®inverter may not perform safety functions unless these functions are
described and expressly permitted.
For safety functions, ensure that the information in the supplied publications is
observed.
Use only components in safety applications that were explicitly designed and supplied
for this purpose by SEW-EURODRIVE.
2.3.2 Hoist applications
When using MOVIMOT®inverters in hoist applications, you must observe the special
configuration and settings for hoist applications specified in the operating instructions for
MOVIMOT®.
MOVIMOT®inverters may not be used as a safety device in hoist applications.
2.4 Transportation, storage
You must observe the notes on transportation, storage and proper handling. Comply
with the requirements for climatic conditions stated in chapter "Technical Data" of the
operating instructions. Tighten installed eyebolts securely. They are designed for the
weight of the MOVIMOT®drive. Do not attach any additional loads. Use suitable,
sufficiently rated handling equipment (e.g. rope guides) if required.
2.5 Installation
The units must be installed and cooled according to the regulations and specifications
in the corresponding documentation.
Protect the MOVIMOT®inverters from improper strain.
The following applications are prohibited unless the unit is explicitly designed for such
use:
• Use in potentially explosive atmospheres.
• Use in areas exposed to harmful oils, acids, gases, vapors, dust, radiation, etc.
• Use in non-stationary applications with strong mechanical oscillation and impact
loads, as specified in the documentation
2.6 Electrical connection
Observe the applicable national accident prevention guidelines when working on live
MOVIMOT®drive inverters (e.g. BGV A3).
Perform electrical installation according to the pertinent regulations (e.g. cable cross
sections, fusing, protective conductor connection). For any additional information, refer
to the applicable documentation.
For information on EMC-compliant installation – such as shielding, grounding,
arrangement of filters and routing of lines – refer to the documentation. The manufac-
turer of the system or machine is responsible for maintaining the limits established by
EMC legislation.

Compact Operating Instructions – MOVIMOT® MM..D with AC Motor DT/DV 7
2
Safe disconnection
Safety Notes
Protective measures and protection devices must comply with the regulations in force
(e.g. EN 60204 or EN 61800-5-1).
A voltage test according to EN 61800-5-1:2007 chapter 5.2.3.2 is required for
MOVIMOT®drives prior to startup to ensure insulation.
2.7 Safe disconnection
MOVIMOT®inverters meet all requirements for safe disconnection of power and
electronic connections in accordance with EN 61800-5-1. All connected circuits must
also satisfy the requirements for safe disconnection.
2.8 Operation
Systems with integrated MOVIMOT®inverters must be equipped with additional
monitoring and protection devices according to the applicable safety guidelines, such as
the law governing technical equipment, accident prevention regulations, etc. Additional
protective measures might be necessary for applications with increased potential risk.
Do not touch live components or power connections immediately after disconnecting the
MOVIMOT®inverter, the field distributor (if installed) or the bus module (if installed) from
the supply voltage because there may still be some charged capacitors. Wait at least for
1 minute after having switched off the supply voltage.
As soon as supply voltage is present at the MOVIMOT®inverter, the terminal box must
be closed, which means that:
• The MOVIMOT®inverter must be screwed on.
• The terminal box cover of the field distributor (if present) and the bus module (if
present) must be bolted down.
• The connector of the hybrid cable (if installed) must be connected and screwed on.
Note: The maintenance switch of the field distributor (if installed) only disconnects the
connected MOVIMOT®drive or motor from the power supply system. The terminals of
the field distributor remain connected to the line voltage even after the maintenance
switch is activated.
The fact that the status LED and other display elements are no longer illuminated does
not indicate that the unit has been disconnected from the supply system and no longer
carries any voltage.
Mechanical blocking or internal safety functions of the unit can cause a motor standstill.
Eliminating the cause of the problem or performing a reset may result in the drive re-
starting automatically. If, for safety reasons, this is not permitted for the driven machine,
disconnect the unit from the supply system before correcting the error.
Caution: Danger of burns: The surface temperature of the MOVIMOT®drive and of
external options, e.g. the heat sink of the braking resistor, can exceed 60 °C during
operation!

8Compact Operating Instructions – MOVIMOT® MM..D with AC Motor DT/DV
3Sample motor nameplate
Type Designations
3 Type Designations
3.1 Sample motor nameplate
1996182283
KA 77 DT 90L4 BMG/MM15/MLU
Additional feature: inverter 1)
1) Nameplate only displays options installed at the factory.
MOVIMOT®inverter
Optional design motor (brake)
Size, number of poles on motor
Motor series
Gear unit size
Gear unit series
SEW -EURODRIVE
SEW -EURODRIVE
Typ
Nr.
KW
kg 73
50Hz
60Hz
r/min
Bremse
KA77 DT90L4/BMG/MM15/MLU
3009818304. 0001. 99
1,5 / 50 HZ
V380-500
V380-500
22/1400
V230
Ma 665
IEC 34
B3
0,99
3,50
3,50
54 F
64,75
Kl
:1
Schmierstoff
Bruchsal / Germany
3~
IM
cos
A
A
IP
Gleichrichter
i
Nm 20
Nm
Made in Germany 184103 3.14

Compact Operating Instructions – MOVIMOT® MM..D with AC Motor DT/DV 9
3
Sample inverter nameplate
Type Designations
3.2 Sample inverter nameplate
3.3 Unit identification
The unit identification [1] on the top of the MOVIMOT®inverter provides information
about the inverter type [2], inverter part number [3], unit power [4].
1957927307
MM 15 D – 503 – 00
Design (00 = Standard)
Connection type (3 = 3-phase)
Supply voltage
(50 = AC 380 – 500 V)
(23 = AC 200 – 240 V)
Version D
Motor power (15 = 1.5 kW)
MOVIMOT®series
Status: 10 12 -- A -- -- 10 10 12
02 / 08 444
Typ MM15D-503-00
Sach.Nr. 18215033
Eingang / Input
U=
f=
I=
T= -30...40C
I=3.5A AC 4.0A AC
f=
50...60Hz
D-76646 Bruchsal
MOVIMOT
Antriebsumrichter P-Motor
P-Motor (S3/25%): 2.2kW / 3.3HP
1.5kW / 2.0HP
Drive Inverter
Use 60/75°C copper wire only. Tighten terminals to 13,3in. - ibs.(1.5 Nm)
Suitable for use on a circuit capable of delivering not more than 5000ms
Made in Germany 2...120Hz
3x0V...UInput U=
3x380...500V AC
Ausgang / Output
Serien Nr.0886946
CH01
N2936
457916555
[2]
[4][3]
[1]

10 Compact Operating Instructions – MOVIMOT® MM..D with AC Motor DT/DV
3"Mounting close to the motor" design
Type Designations
3.4 "Mounting close to the motor" design
The following illustration shows an example of the MOVIMOT®inverter mounted close
to the motor with corresponding nameplate and type designation:
457921547
MM15D-503-00/0/P21A/RO1A/APG4
Plug connector for the connection to the motor
Terminal box design
Adapter for installation close to the motor
21 = Size 1
22 = Size 2
Connection type
0 = 
1 = 
MOVIMOT®inverter
MM15D-503-00/0/P21A/RO1A/APG4

Compact Operating Instructions – MOVIMOT® MM..D with AC Motor DT/DV
4
MOVIMOT®gearmotor
Mechanical Installation
4 Mechanical Installation
4.1 MOVIMOT®gearmotor
4.1.1 Before you start
Only install the MOVIMOT®drive if:
• The entries on the nameplate of the drive match the voltage supply system.
• The drive is undamaged (no damage caused by transportation or storage).
• You are certain that the following requirements have been fulfilled:
– Ambient temperature corresponds to the specifications in chapter "Technical
Data" of the operating instructions. Note that the temperature range of the gear
unit may also be restricted (see gear unit operating instructions).
– No oil, acid, gas, vapors, radiation, etc.
Installation
tolerances
The following tables shows the permitted tolerances of the shaft ends and flanges of the
MOVIMOT®drive.
Shaft end Flanges
Diameter tolerance according to EN 50347
• ISO j6 with Ø ≤26 mm
• ISO k6 with Ø ≤38 mm up to ≤48 mm
• ISO m6 at Ø > 55 mm
• Center bore in accordance with DIN 332,
shape DR..
Centering shoulder tolerance in accordance
with EN 50347
• ISO j6 with Ø ≤250 mm
• ISO h6 with Ø > 300 mm

12 Compact Operating Instructions – MOVIMOT® MM..D with AC Motor DT/DV
4MOVIMOT®gearmotor
Mechanical Installation
4.1.2 Installing MOVIMOT®
Observe the following notes for mounting the MOVIMOT®drive:
• Install/mount the MOVIMOT®drive only in the mounting position specified on the
motor nameplate on a level, vibration-free, and torsionally rigid support structure.
• Clean the output shafts thoroughly to ensure they are free of anti-corrosion agents
(use a commercially available solvent). Do not allow the solvent to penetrate the
bearings and shaft seals – this could damage the material.
• Carefully align the MOVIMOT®inverter and the motor, to avoid placing any
unacceptable strain on the motor shafts (observe permissible overhung load and
axial load data!).
• Do not butt or hammer the shaft end.
• Use an appropriate cover to prevent objects or fluids from entering motors in vertical
mounting positions.
• Ensure there is sufficient clearance around the unit to allow for adequate cooling.
Furthermore, the unit must be positioned in such a way that it does not reuse the air
warmed by other devices.
• Balance components for subsequent mounting on the shaft with a half key (output
shafts are balanced with a half key).
• Existing condensation drain holes must be sealed with plastic plugs. They must not
be opened unless needed.
• Open condensation drain holes are not permitted. If condensation drain holes are
open, higher enclosures are no longer possible.
4.1.3 Installation in damp locations or in the open
Observe the following notes for mounting the MOVIMOT®drive in damp areas or in the
open:
• Use suitable cable glands for the supply leads (use reducing adapters if necessary).
• Coat the threads of cable glands and filler plugs with sealing compound and tighten
them well; then coat them again.
• Seal the cable entries well.
• Clean the sealing faces of the MOVIMOT®inverter well before re-assembly.
• If the corrosion protection coating is damaged, restore the coating.
• Check enclosure according to nameplate.
STOP
The degree of protection specified in the technical data only applies if the MOVIMOT®
inverter is properly installed.
When the MOVIMOT®inverter is removed from the connection box, it might be
damaged by humidity or dust.
• Protect the MOVIMOT®inverter when it is removed from the connection box.

Compact Operating Instructions – MOVIMOT® MM..D with AC Motor DT/DV 13
4
Installing the MOVIMOT®inverter close to the motor
Mechanical Installation
4.2 Installing the MOVIMOT®inverter close to the motor
The following figure shows the mounting dimensions for installing the MOVIMOT®
inverter close to the motor:
458277771
A B
MM03D503-00 – MM15D-503-00
MM03D233-00 – MM07D-233-00 140 mm 65 mm
MM22D503-00 – MM40D-503-00
MM11D233-00 – MM22D-233-00 170 mm 65 mm
A
B
M6
M6

14 Compact Operating Instructions – MOVIMOT® MM..D with AC Motor DT/DV
4Tightening torques
Mechanical Installation
4.3 Tightening torques
4.3.1 MOVIMOT®inverter
Tighten the screws on the MOVIMOT®inverter using 3.0 Nm (27 lb.in) working
diagonally across.
4.3.2 Screw plugs
Tighten screw plugs of potentiometer f1 and connection X50 using 2.5 Nm (22 lb.in).
4.3.3 Cable glands
It is essential to observe the manufacturer's specifications for the cable glands.
458577931
458570379

Compact Operating Instructions – MOVIMOT® MM..D with AC Motor DT/DV 15
4
Tightening torques
Mechanical Installation
4.3.4 Screw plugs for cable entries
Tighten screw plugs with 2.5 Nm (22 lb.in).
4.3.5 Tightening torques for terminals
Use the following tightening torques for terminals during installation:
322777611
1999952907
[1]
[2]
[3]
[4]
[5]
0.5 – 0.7 Nm (4 – 6 lb.in)
0.5 – 0.7 Nm (4 – 6 lb.in)
0.8 – 1.5 Nm (7 – 10 lb.in)
1.2 – 1.6 Nm (11 – 14 lb.in)
2.0 – 2.4 Nm (18 – 21 lb.in)
[1]
[5]
[2] [3] [4]

16 Compact Operating Instructions – MOVIMOT® MM..D with AC Motor DT/DV
5Installation instructions
Electrical Installation
5 Electrical Installation
5.1 Installation instructions
5.1.1 Connecting supply system leads
• The rated voltage and frequency of the MOVIMOT®inverter must correspond to the
data for the power supply system.
• Cable cross section: according to input current Iline for rated power (see chapter
"Technical Data" in the operating instructions).
• Permitted cable cross section of MOVIMOT®terminals (does not apply to field
distributors):
• Permitted length of the conductor end sleeve: At least 8 mm
• Use conductor end sleeves without insulating shrouds (DIN 46228 part 1, material E-
CU).
• Install line fuses at the beginning of the power supply cable behind supply bus
junction (see the section "Connection of MOVIMOT®basic unit"). Use only D, D0 or
NH melting fuses or circuit breakers for F11/F12/F13. Select the fuse size according
to the cable cross section.
• SEW recommends using earth-leakage monitors with pulse code measuring in
voltage supply systems with a non-earthed star point (IT systems). Using such
devices prevents the earth-leakage monitor mis-tripping due to the ground
capacitance of the inverter.
Field wiring power terminals
1.0 mm2 - 4.0 mm2 (2 x 4.0 mm2)
AWG17 – AWG10 (2 x AWG10)
Control terminals
Single-wire conduc-
tor
(bare wire)
Flexible conductor
(bare litz wire)
Conductor with
Conductor end
sleeve
without
insulating shrouds
Conductor with
Conductor end
sleeve
with
insulating shrouds
0.5 mm2– 1.0 mm20.5 mm2– 0.75 mm2
AWG20 – AWG17 AWG20 – AWG19
Only connect single-wire conductors or flexible conductors with or without conductor end
sleeve (DIN 46228 part 1, material E-CU)

Compact Operating Instructions – MOVIMOT® MM..D with AC Motor DT/DV 17
5
Installation instructions
Electrical Installation
5.1.2 Earth-leakage circuit breakers
• Do not use a conventional earth-leakage circuit breaker as a protective device.
Universal current-sensitive earth leakage circuit-breakers (tripping current 300 mA)
are permitted as a protective device. During normal operation of MOVIMOT®
inverter, earth-leakage currents of > 3.5 mA can occur.
• SEW-EURODRIVE recommends that you do not use earth-leakage circuit breakers.
However, if an earth-leakage circuit breaker is stipulated for direct or indirect protec-
tion against contact, observe the following note in accordance with EN 61800-5-1:
5.1.3 Input contactor
• Only use a contactor of utilization category AC3 (EN 60947-4-1) as an input
contactor.
5.1.4 EMC-compliant installation
With respect to the EMC regulation, frequency inverters cannot be operated as stand-
alone units. Regarding EMC, they can only be evaluated when they are integrated in a
drive system. Conformity is declared for a described, CE-typical drive system. The
operating instructions contain further information.
WARNING
Wrong type of earth-leakage circuit breaker installed.
Severe or fatal injuries.
MOVIMOT®can cause direct current in the protective earth. In cases where an earth-
leakage circuit breaker is used for protection against direct or indirect contact, only
install a type B earth-leakage circuit breaker on the power supply end of the
MOVIMOT®inverter.
NOTICE
• Do not use the K11 input contactor (see wiring diagram (page 20)) for jog mode, but
only for switching the inverter on and off. For jog mode, use the the commands "CW
/ Stop" or "CCW / Stop".
• Observe a minimum switch-off time of 2 s for the supply system contactor K11.
WARNING
This drive system is not designed for operation on a public low voltage supply system
that supplies residential areas.
INFORMATION
• This is a product with restricted availability in accordance with IEC 61800-3. It may
cause EMC interference. In this case, it is recommended for the operator to carry
out suitable measures.
• For detailed information on EMC compliant installation, refer to the publication
"Electromagnetic Compatibility in Drive Engineering" from SEW-EURODRIVE.

18 Compact Operating Instructions – MOVIMOT® MM..D with AC Motor DT/DV
5Installation instructions
Electrical Installation
5.1.5 Notes on PE connection
Earth-leakage currents ≥3.5 mA may occur during normal operation. To meet the
requirements of EN 61800-5-1 observe the following note:
• Route a second PE conductor with the cross section of the supply system lead in
parallel to the protective earth via separate terminals or use a copper protective earth
conductor with a cross section of 10 mm2.
DANGER
Incorrect connection of PE.
Death, severe injuries or damage to property from electric shock.
• The permitted tightening torque for the screw fitting is 2.0 - 2.4 Nm (18 - 21 lb.in).
• Observe the following notes regarding PE connection.
Prohibited assembly
sequence
Recommendation:
Assembly with forked cable lug
Permitted for all cross sections
Assembly with thick solid wire
Permitted for cross sections up to
max. 2.5 mm2
323042443 323034251 323038347
[1] Forked cable lug suitable for M5 PE screws
[1]
M5
2.5 mm²
M5

Compact Operating Instructions – MOVIMOT® MM..D with AC Motor DT/DV 19
5
Installation instructions
Electrical Installation
5.1.6 Installation altitude above 1000 m above sea level
MOVIMOT®drives with line voltages of 200 to 240 V or 380 to 500 V, can be used in
altitudes of 1000 m and up to a maximum of 4000 m above sea level under the following
conditions.1)
• The rated continuous power is reduced based on the reduced cooling above 1000 m
(see "Technical Data" chapter in the operating instructions).
• Above 2000 m above sea level, the air and creeping distances are only sufficient for
overvoltage class 2. If the installation requires overvoltage class 3, you will have to
install additional external overvoltage protection to limit overvoltage peaks to 2.5 kV
phase-to-phase and phase-to-ground.
• If safe electrical disconnection is required, it must be implemented outside the device
at altitudes of 2000 msl (safe electrical disconnection in accordance with EN 61800-
5-1).
• In installation altitudes between 2000 m to 4000 msl, the permitted rated power
supply voltages are reduced as follows:
– By 6 V per 100 m for MM..D-503-00
– By 3 V per 100 m for MM..D-233-00
5.1.7 Connecting 24 V supply
• Power the MOVIMOT®inverter either via an external 24 V supply or the MLU..A or
MLG..A options.
5.1.8 Binary control
• Connect the required control leads.
• Use shielded cables as control cables and route them separately from supply system
cables.
5.1.9 UL-compliant installation
• Use only copper cables for temperature range 60/75 °C as connection lead.
• The permitted tightening torques for MOVIMOT®power terminals are: 1.5 Nm
(13 lb.in).
• The permitted supply system voltage is 500 V (400/500 V inverter) or 240 V (230 V
inverter). Information about the max. permitted short-circuit currents of the supply
system and the fuse is listed on the nameplate of the MOVIMOT®inverter.
1) The maximum altitude is limited by creeping distances and flameproof components, such as electrolytic
capacitors.
INFORMATION
• Only use certified units with a limited output voltage (Vmax = DC 30 V) and limited
power (P ≤100 VA) as an external DC 24 V voltage source.
• The UL certification only applies to the operation on voltage supply systems with
voltages to ground of max. 300 V. The UL-certification does not apply to the
operation on voltage supply systems with a non-grounded star point (IT systems).

20 Compact Operating Instructions – MOVIMOT® MM..D with AC Motor DT/DV
5Connection of MOVIMOT®
Electrical Installation
5.2 Connection of MOVIMOT®
2000232971
Functions of the CW/Stop + CCW/Stop terminals
for binary control:
Direction of
rotation
CW active
Direction of rotation
CCW active
Functions of terminals f1/f2:
Setpoint f1
active
Setpoint f2 active
Functions of the CW/Stop + CCW/Stop terminals
for control via RS-485 interface / fieldbus:
Both directions of rotation
are enabled
Only CW direction
is enabled
Pre-selected setpoints for CCW
rotation result in standstill of drive
Only CCW operation
is enabled
Setpoint specifications for CW
rotation result in standstill of drive
Drive is inhibited or is being
brought to a stop
[1] DC 24 V supply (external or MLU..A/MLG..A options)
[2] CW / stop
[3] CCW / stop
[4] Setpoint changeover f1/f2
[5] Ready signal (contact closed = ready for operation)
[6] BW.. braking resistor
(only for MOVIMOT®drives without mechanical brake)
M
3~
L1
L2
L3
PE
K11
F11/F12/F13
K1
RS-485
13
14
15
L1
L2
L3
24V
R
L
f1/f2
K1a
K1b
RS-
RS+
=
+
-
BMG
MOVIMOT
®
RD
WH
BMG
MOVIMOT
®
[1]
[2]
[3]
[4]
[5]
24 V
DC
BU
BW [6]
R
L
24V
R
L
24V
R
L
24V
f1/f2
R
L
24V
f1/f2
24V
R
L
24V
R
L
24V
R
L
24V
R
L