SEW-Eurodrive MOVIMOT DRN DSI Series User manual

*27803899_0223*
Drive Technology \ Drive Automation \ System Integration \ Services
Operating Instructions
Mechatronic Drive Unit
MOVIMOT® advanced
DRN..DSI.., DR2C..DSI.. (EtherCAT®/SBusPLUS)
Edition 02/2023 27803899/EN

SEW-EURODRIVE—Driving the world

Table of Contents
Operating Instructions – MOVIMOT® advanced 3
Table of Contents
1 General information.................................................................................................................. 5
1.1 Structure of the safety notes ...........................................................................................5
2 Safety notes for MOVIMOT® advanced ................................................................................... 6
2.1 Target group ...................................................................................................................6
2.2 Designated use ...............................................................................................................6
2.3 Functional safety technology ..........................................................................................7
2.4 Transportation.................................................................................................................8
2.5 Creating a safe working environment .............................................................................9
2.6 Installation/assembly.....................................................................................................11
2.7 Protective separation ....................................................................................................11
2.8 Electrical installation .....................................................................................................12
2.9 Startup/operation ..........................................................................................................12
3 Device structure ..................................................................................................................... 13
3.1 Example nameplate and type designation of the drive unit ..........................................13
3.2 Electronics ....................................................................................................................17
3.3 Example nameplate and type designation of electronics..............................................19
3.4 Markings .......................................................................................................................21
4 Mechanical installation .......................................................................................................... 23
4.1 Installation notes ...........................................................................................................23
4.2 Tolerances for torque ratings ........................................................................................23
4.3 Installation requirements...............................................................................................24
4.4 Setting up the drive unit ................................................................................................25
4.5 Tightening torques ........................................................................................................29
5 Electrical installation.............................................................................................................. 31
5.1 Installation instructions..................................................................................................31
5.2 Terminal assignment of MOVIMOT® advanced DSI ....................................................41
5.3 MOVIMOT® advanced DSI connection diagram ..........................................................45
5.4 Cable routing and cable shielding.................................................................................46
5.5 EMC cable glands.........................................................................................................52
5.6 Plug connectors ............................................................................................................53
5.7 PC connection...............................................................................................................62
6 Startup ..................................................................................................................................... 63
6.1 Startup notes.................................................................................................................63
6.2 Startup requirements ....................................................................................................64
6.3 DIP switches .................................................................................................................65
6.4 Startup procedure .........................................................................................................67
6.5 Startup with CBG22A on-site keypad ...........................................................................69
6.6 Configuring the drive behavior at standstill (FCB 02, FCB 13, FCB 14) .......................69
7 Operation................................................................................................................................. 70
7.1 Switch disconnector ......................................................................................................70
7.2 Drive unit behavior in case of a voltage failure .............................................................70
8 Service..................................................................................................................................... 71
27803899/EN – 02/2023

Table of Contents
Operating Instructions – MOVIMOT® advanced
4
8.1 Failures of the mechanical drive ...................................................................................71
8.2 Resetting fault messages..............................................................................................73
8.3 Description of status and operating displays ................................................................73
8.4 Device replacement ......................................................................................................81
8.5 Shutdown ......................................................................................................................85
8.6 Waste disposal..............................................................................................................86
9 Inspection and maintenance ................................................................................................. 87
9.1 Inspection and maintenance intervals...........................................................................87
9.2 Inspection and maintenance work ................................................................................88
27803899/EN – 02/2023

1
General information
Structure of the safety notes
Operating Instructions – MOVIMOT® advanced 5
1 General information
1.1 Structure of the safety notes
1.1.1 Meaning of signal words
The following table shows the graduation and meaning of the signal words in the
warnings:
Signal word Meaning Consequences if not observed
DANGER Imminent danger Death or severe injuries
WARNING Possible, dangerous situation Death or severe injuries
CAUTION Possible, dangerous situation Slight injuries
NOTICE Possible damage to property Damage to the product or its envi-
ronment
INFORMATION Useful information or tip: Simplifies
handling of the product.
1.1.2 Meaning of the hazard symbols
The hazard symbols in the safety notes have the following meaning:
Hazard symbol Meaning
General hazard
Warning of dangerous electrical voltage
Warning of hot surfaces
Warning of risk of crushing
Warning of automatic restart
27803899/EN – 02/2023

2Safety notes for MOVIMOT® advanced
Target group
Operating Instructions – MOVIMOT® advanced
6
2 Safety notes for MOVIMOT® advanced
2.1 Target group
Specialist for me-
chanical work
Any mechanical work may be performed only by adequately qualified specialists. Spe-
cialists in the context of this documentation are persons who are familiar with the
design, mechanical installation, troubleshooting, and maintenance of the product, and
who possess the following qualifications:
• Qualifications in the field of mechanics in accordance with the national regulations
• Familiarity with this documentation
Specialist for elec-
trotechnical work
Any electrotechnical work may be performed only by electrically skilled persons with a
suitable education. Electrically skilled persons in the context of this documentation are
persons who are familiar with electrical installation, startup, troubleshooting, and main-
tenance of the product, and who possess the following qualifications:
• Qualifications in the field of electrical engineering in accordance with the national
regulations
• Familiarity with this documentation
Additional qualifi-
cations
In addition to that, these persons must be familiar with the valid safety regulations and
laws, as well as with the requirements of the standards, directives, and laws specified
in this documentation.
The persons must have the express authorization of the company to operate, pro-
gram, parameterize, label, and ground devices, systems, and circuits in accordance
with the standards of safety technology.
Instructed persons All work in the areas of transport, storage, installation, operation and waste disposal
may only be carried out by persons who are trained and instructed appropriately.
These instructions must enable the persons to carry out the required activities and
work steps safely and in accordance with regulations.
2.2 Designated use
The product is intended for installation in electrical plants or machines.
In case of installation in electrical systems or machines, startup of the product is pro-
hibited until it is determined that the machine meets the requirements stipulated in the
local laws and directives. For Europe, Machinery Directive 2006/42/EC as well as the
EMC Directive 2014/30/EU apply. Observe EN60204-1 (Safety of machinery - elec-
trical equipment of machines). The product meets the requirements stipulated in the
Low Voltage Directive 2014/35/EU.
The standards given in the declaration of conformity apply to the product.
Technical data and information on the connection conditions are provided on the
nameplate and in chapter "Technical data" in the documentation. Always comply with
the data and conditions.
Unintended or improper use of the product may result in severe injury to persons and
damage to property.
Do not use the product as a climbing aid.
27803899/EN – 02/2023

2
Safety notes for MOVIMOT® advanced
Functional safety technology
Operating Instructions – MOVIMOT® advanced 7
2.2.1 Hoist applications
To avoid danger of fatal injury by falling hoists, observe the following points when us-
ing the product in lifting applications:
• The product is not designed for use as a safety device in lifting applications.
• Use additional monitoring systems or mechanical protection devices.
2.2.2 Restrictions of use
The following applications are prohibited unless the device is explicitly designed for
such use:
• Use in potentially explosive areas.
• Use in areas exposed to harmful oils, acids, gases, vapors, dust, and radiation.
• Operation in applications with impermissibly high mechanical vibration and shock
loads in excess of the regulations stipulated in EN61800-5-1.
• Use at an elevation of more than 3800m above sea level.
The product can be used at altitudes above 1000 m above sea level up to 3800 m
above sea level under the following conditions:
• The reduction of the nominal output current and/or the line voltage is considered
according to the data in chapter "Technical data" in the documentation.
• Above 2000m above sea level, the air and creepage distances are only sufficient
for overvoltage class II according to EN60664. At altitudes above 2000m above
sea level, limiting measures must therefore be taken that reduce the line side over-
voltage from category III to category II for the entire system.
• If a protective electrical separation (in accordance with EN 61800‑5‑1 and
EN 60204‑1) is required, then implement this outside the product at altitudes of
more than 2000m above sea level.
2.3 Functional safety technology
The product contains the STO - Safe Torque Off safety subfunction. Additional safety
subfunctions can be optionally provided for the product.
The safety subfunctions are deactivated in the delivery state. The product is not
allowed to perform any safety functions without higher-level safety systems.
Please observe the product manual and the manual of the optional safety option of
this device to use the STO safety subfunction or additional subfunctions.
27803899/EN – 02/2023

2Safety notes for MOVIMOT® advanced
Transportation
Operating Instructions – MOVIMOT® advanced
8
2.4 Transportation
Inspect the shipment for damage as soon as you receive the delivery. Inform the ship-
ping company immediately about any damage. If the product or the packaging is dam-
aged, do not assemble, install, connect, or start up the product. If the packaging is
damaged, the product itself may also be damaged.
The lifting eye is designed to carry only the mass of the motor without gear unit.
Tighten the retaining screws of the lifting eye. Mounted gear units have separate sus-
pension attachments, which must be used according to the gear unit operating instruc-
tions when lifting the gearmotor. Do not mount any additional loads.
The following figure depicts the position of the lifting eye of the motor without gear
unit.
9007224557044491
Remove the lifting eye before connecting the PE cable, see chapter "Electrical installa-
tion" > "Installation instructions".
Store the lifting eye for future service work, see chapter "Service" > "Device replace-
ment".
Observe the following notes when transporting the device:
• Always use all attachment points if available. The attachment points are designed
to carry only the mass of the product. Severe or fatal injuries. Do not apply any ad-
ditional loads.
• Ensure that the product is not subject to mechanical impact.
If necessary, use suitable, sufficiently dimensioned handling equipment.
Do not transport or store the product on the fan guard.
27803899/EN – 02/2023

2
Safety notes for MOVIMOT® advanced
Creating a safe working environment
Operating Instructions – MOVIMOT® advanced 9
2.5 Creating a safe working environment
Before you work on the product, ensure a safe working environment. Observe the fol-
lowing basic safety note:
2.5.1 Performing work on the product safely
Defective or dam-
aged product
Never install defective or damaged products. Observe the following information to
avoid injuries or damage:
• Before installation, check the product for external damage and replace a damaged
product.
Hot surfaces The surface temperature of the product can be very high during operation. Observe
the following information to avoid burns:
• Before touching the product, let the product cool down.
• Do not touch any surfaces of the product during operation, except for the control
elements.
Falling load Observe the following information to avoid death or serious injury due to falling loads:
• Do not stand under the load.
• Secure the area where loads can fall down.
• Use personal protective equipment (helmet, gloves, safety shoes, safety goggles).
• Use a suitable lifting tool (chain hoist, forklift) and transport protection.
Rotating parts Exposed rotating parts and uncontrolled component movements may pose a hazard
when working on the product. Observe the following information to prevent body parts
from being crushed and drawn in:
• Switch off the product before you start working on it.
• Observe all technical data of the product.
• Do not reach into the hazard zone.
• Follow the 5 safety rules in chapter: "Performing electrical work safely"(→210).
Sharp edges Observe the following information to avoid cuts and malfunctions caused by sharp or
non-deburred cutting edges:
• Wear safety gloves.
27803899/EN – 02/2023

2Safety notes for MOVIMOT® advanced
Creating a safe working environment
Operating Instructions – MOVIMOT® advanced
10
2.5.2 Performing electrical work safely
Observe the following information to perform electrical work safely:
Electrical work may only be performed by a qualified electrician or an electronically in-
structed person under the supervision of an electrician.
Observe the 5 safety rules in the specified sequence when working on electrical com-
ponents, unless there are important reasons to deviate from them (observe the specifi-
cations of DIN EN 50110-1 (VDE 0115-1)):
• Disconnect.
• Secure the device against a restart.
• Check that no voltage is applied.
• Ground and short-circuit.
• Cover or cordon off neighboring live parts.
Observe that the fact that the operation LED and other display elements are no longer
illuminated does not indicate that the product has been disconnected from the supply
system and no longer carries any voltage.
Dangerous voltage All the power connections and the cables and terminals connected thereto have dan-
gerous voltages when powered on. This is also the case if the product is inhibited and
the motor is at a standstill. Observe the following information to prevent electric shock:
• Do not touch any exposed live parts (e.g., male contacts, the plug connectors, ter-
minals).
• Secure all open live components with a touch guard.
• Ensure that the connection boxes are closed and screwed down before applying
the supply voltage.
• Before applying the supply voltage, make sure that all required covers are mount-
ed.
• Secure the output shaft against rotation when working without touch guard.
Danger due to
electric arc
An electric arc may occur when plug-in connections are disconnected or connected
while voltage is applied (e.g. connection between drive and control). Observe the fol-
lowing information to prevent damage to electrical components:
• Do not disconnect power connections during operation.
• Do not connect power connections during operation.
• Ensure that the product is de-energized before disconnecting and connecting the
plug-in connections.
Dangerous voltage Voltage may still be present in live product parts and the power connectors, even after
disconnecting the supply voltage, due to charged capacitors. Observe the following in-
formation:
• Observe the following waiting periods before performing electrical work and after
disconnecting the supply voltage: 5minutes.
• Please also observe the labels and hazard symbols on the product.
27803899/EN – 02/2023

2
Safety notes for MOVIMOT® advanced
Installation/assembly
Operating Instructions – MOVIMOT® advanced 11
2.6 Installation/assembly
Ensure that the product is installed and cooled in accordance with the regulations in
the documentation.
Protect the product from excessive mechanical strain. The product and its mounted
components must not protrude into the path of persons or vehicles. Ensure that no
components are deformed or no insulation spaces are modified, particularly during
transportation. Electrical components must not be mechanically damaged or de-
stroyed.
Observe the notes in chapter "Mechanical installation" in the documentation.
2.7 Protective separation
The product meets all requirements for protective separation of power and electronics
connections in accordance with IEC 61800-5-1. The connected signal circuits must
meet requirements according to SELV (Safety Extra Low Voltage) or PELV (Protective
Extra Low Voltage) to ensure protective separation. The installation must meet the re-
quirements for protective separation.
In order to avoid exceeding the permitted contact voltages in SELV or PELV power cir-
cuits in the event of a fault, continuous equipotential bonding is required in the vicinity
of these power circuits. If this is not possible, other preventive measures must be
taken. These preventive measures are described in IEC61800-5-1.
27803899/EN – 02/2023

2Safety notes for MOVIMOT® advanced
Electrical installation
Operating Instructions – MOVIMOT® advanced
12
2.8 Electrical installation
The preventive measures and protection devices must comply with the applicable reg-
ulations (e.g. EN60204-1 or EN61800-5-1).
2.8.1 Stationary application
The necessary preventive measure for the product is:
Type of energy transfer Preventive measure
Direct power supply Ground connection
2.8.2 Regenerative operation
The drive is operated as a generator due to the kinetic energy of the system/machine.
Before opening the connection box, secure the output shaft against rotation.
2.9 Startup/operation
Observe the safety notes in chapters "Startup" and "Operation" in this documentation.
Depending on the degree of protection, products may have live, uninsulated, and
sometimes moving or rotating parts as well as hot surfaces during operation.
Never plug or unplug plug connectors while they are energized.
Do not separate the connection to the product during operation. This may result in
dangerous electric arcs damaging the product.
If you disconnect the product from the voltage supply, do not touch any live compo-
nents or power connections because capacitors might still be charged. Observe the
following minimum switch-off time:
5minutes.
Observe the corresponding information signs on the product.
The fact that the operation LED and other display elements are no longer illuminated
does not indicate that the product has been disconnected from the supply system and
no longer carries any voltage.
Mechanical blocking or internal protective functions of the product can cause a motor
standstill. Eliminating the cause of the problem or performing a reset may result in the
drive restarting automatically. If, for safety reasons, this is not permitted for the drive-
controlled machine, first disconnect the product from the supply system and then start
troubleshooting.
Risk of burns: The surface temperature of the product can exceed 60°C during opera-
tion. Do not touch the product during operation. Let the product cool down before
touching it.
27803899/EN – 02/2023

3
Device structure
Example nameplate and type designation of the drive unit
Operating Instructions – MOVIMOT® advanced 13
3 Device structure
3.1 Example nameplate and type designation of the drive unit
3.1.1 MOVIMOT®advanced nameplates
The MOVIMOT® advanced drive unit is always equipped with 2 nameplates:
• Nameplate 1: Data of the drive unit.
• Nameplate 2: Data of the motor and additional data of the drive unit
Nameplate 1 (MOVIMOT® advanced DSI drive unit)
The following figure shows an example of a drive unit nameplate. The format of the
type designation can be found in chapter entitled “Type designation ...”.
LISTED
IND.CONT.EQ.
2D06
UL Enclosure Type1
01
FS
76646 Bruchsal/Germany
R97 R57 DRN80M4/DI/DSI/BW1
01.1234567890.0001.0
0025 IES2
3~ IEC60034 ML
P
MA
03
0.75kW
820Nm
1:12VT
fN 50..60Hz
UN 380Y/220..
500Y/289V
nA
nR
0.67...8.1r/min
IN 1.90A
2102 107 4
TEFC Made in Germany
[6]
[8]
[9]
[7]
[2]
[3]
[4]
[1]
[5]
27021630184769035
[1] FS logo
[2] Identification/approvals of the drive unit
[3] Mechanic output data of the drive unit
• Output speed range
• Speed setting range
• Nominal torque
• Nominal power
[4] System efficiency of the drive unit
[5] Nominal output current of the electronics cover (inverter)
0020 = 2.0A
to
0160 = 16.0A
[6] Product label with QR code. The QR code can be scanned. You will be
redirected to the digital services of SEW‑EURODRIVE. There, you
have access to product-specific data, documents, and further services.
In the "Documentation" > "Data and documents" area, the
product manual of the device with further information is available.
[7] Electrical input data of the drive unit
• Voltage range
• Line frequency range
• Nominal line current (at 400V)
[8] Serial number of the drive unit
[9] Type designation of the drive unit
27803899/EN – 02/2023

3Device structure
Example nameplate and type designation of the drive unit
Operating Instructions – MOVIMOT® advanced
14
Nameplate 2 (..DR2C.. motor)
The following image shows an example of a nameplate of the WA..DR2C.. gearmotor
76646 Bruchsal/Germany
WA20 DR2C71MSA4/TF
01.01234567890.0001.22 Inverter duty only 3~IEC60034
VPWM
Hz
67
67
A
1.77
2.3
2000
2000
nmax6000r/min Imax 4.8 A Mpk9.0 Nm
Thermal permissible load
r/min Usys 400 V Y
Up 273 V
kW
0.69
0.9
3.3
4.3
eff%
84.5
81.1
IE5
IE3
Th.Kl. 155(F)
i19.5 ne pk 4500 r/min Ma pk 42 Nm
SEW PG 460 Synth.Öl/0.24 l
IM M1A
kg 8.645 MadeinGermany 2102 366 2 DE
ML03
Nm
-20..40 °C
IP 55
PM
N S
[13]
[12]
[11]
[14]
[15]
[9]
[10]
[8][7][6][5][1] [2] [3] [4]
40120498955
[1] Rated speed of the motor
[2] Rated frequency of the motor
[3] Rated current in the connection type of the motor
[4] Rated power of the motor
[5] Efficiency and IE class of the motor at the measurement point
[6] Nominal voltage and connection type of the motor
[7] Number of phases and rating/performance standards
[8] Identification/approvals of the motor
[9] Motor thermal class
[10] Ambient temperature range of the drive unit
[11] Degree of protection of the drive unit
[12] Weight of drive unit
[13] Gear unit data:
• Gear unit ratio
• Output speed of the gear unit
• Output torque of the gear unit
• Oil type and oil fill volume
[14] Serial number of the drive unit
[15] Type designation of the drive unit
27803899/EN – 02/2023

3
Device structure
Example nameplate and type designation of the drive unit
Operating Instructions – MOVIMOT® advanced 15
Nameplate 2 (DRN.. motor)
The following image shows an example of a nameplate of the DRN.. motor
76646 Bruchsal / Germany
DRN80M4/FF/DI/DFC/BW1
01.1774473607.0001.00 Inverter duty 3~IEC60034VPWM
Hz 60 r/min 1751 V266 Δ
kW 0.75 S1 [1.0 hp]
Duty S1
Th.Kl. 155(F)
CT 300-1800rpm
FF FF165 D200
MtgPos B5
MtgPos M1
i 30,18 Nm 245
CLP 220 Miner.Öl/0.8 l
DI0C00
kg 20.000 AMB °C -20..40 Made in Germany
188 695 9 DE
WE 19X40
ML 03
Vbr 230AV
Nm 20
P.F. 0.7 S.F.1.0 IP54 TEFC
A2.7 eff% 85,5 IE3
[17]
[16]
[15]
[14]
[13]
[12]
[10]
[9] [8]
[11]
[7]
[6]
[5]
[4]
[3]
[2][1]
18014430930092299
[1] Rated speed of the motor
[2] Identification/approvals of the motor
[3] Number of phases and rating/performance standards
[4] Nominal voltage and connection type of the motor
[5] IEclass and efficiency of the motor at the rating point
[6] Degree of protection of the drive unit
[7] Rated current in the connection type of the motor
[8] Only for motors with brake:
• Brake supply voltage
• Deceleration torque of the brake
[9] For motors without a gear unit:
• Flange
• Shaft end
• Mounting position
For motors with gear units:
• Gear unit ratio
• Output torque of the gear unit
• Mounting position
• Oil type and oil fill volume
[10] Ambient temperature range of the drive unit
[11] Weight of drive unit
[12] Speed range of the motor
[13] Motor thermal class
[14] Rated power of the motor
[15] Rated frequency of the motor
[16] Serial number of the drive unit
[17] Type designation of the drive unit
27803899/EN – 02/2023

3Device structure
Example nameplate and type designation of the drive unit
Operating Instructions – MOVIMOT® advanced
16
3.1.2 Type designation of the MOVIMOT® advanced DSI
The following table shows the type designation of the drive unit.
R Gear unit series1)
R = Primary gear unit
87 Gear unit size2)
DRN Product family
DRN = Asynchronous motor of the DRN.. series
DR2C = Energy-efficient motor of the DR2C.. series
80 Motor size
71, 80, 90, 100 with electronics cover of size 1
100, 112, 132 with electronics cover of size 2
S Motor length
S = Short
MS = Medium Short
M = Medium
L = Long
MK = Medium (short version)
LS = Long (short version)
4 Number of poles
4 = 4-pole motor
/
BE1 Brake
BE03 = BE03 brake
BE05 = BE05 brake
BE1 = BE1 brake
BE2 = BE2 brake
BE5 = BE5 brake
BE11 = BE11 brake
BE20 = BE20 brake
HF Brake options
HF = Manual brake release, lockable
HR = Manual brake release, automatic disengaging function
/
DI Digital motor integration
DI = Digital interface
/
DSI Communication version
DSI = Direct System Bus Installation
/
27803899/EN – 02/2023

3
Device structure
Electronics
Operating Instructions – MOVIMOT® advanced 17
EI8Z Option
EI8Z = Single-turn encoder with DDI connection
AK8Z = Multi-turn absolute encoder with DDI connection
IV = Plug connector
TF = Motor protection
D11 = Switch disconnector with feedback contact
BW1 = Integrated BW 1 braking resistor
BW2 = Integrated BW 2 braking resistor
PE = Electronics pressure compensation fitting
AL = Metal fan
C = Canopy
RI = Reinforced winding insulation
2W = Shaft end on the motor/brakemotor
1) You can find more gear unit series in the gearmotor catalog
2) You can find more gear unit sizes in the gearmotor catalog
3.2 Electronics
3.2.1 Overview of electronics cover
Devices with the following electronics covers are available depending on the nominal
output current:
Electronics cover
Nominal out-
put current
Type designation Size Image
2.0A DSI...-0020.. Size 1 without cooling fins
2.5A DSI...-0025..
3.2A DSI...-0032..
4.0A DSI...-0040.. Size1 with cooling fins
5.5A DSI...-0055..
7.0A DSI...-0070.. Size 2 without fan
9.5A DSI...-0095..
12.5A DSI...-0125.. Size 2 with fan
16.0A DSI...-0160..
27803899/EN – 02/2023

3Device structure
Electronics
Operating Instructions – MOVIMOT® advanced
18
3.2.2 Connection configuration of the electronics cover
The electronics covers are available in several connection configurations with M12
plug connectors.
If the M12 plug connectors X4233_1 and X4233_2 for fieldbus connection are not
available at the electronics cover, fieldbus connection is realized via the mini I/O plug
connectors X42 and X43 of the connection unit.
Type designation
electronics cover
• Connection configuration
Description Image
DFC.0..
DSI.0..
• Fieldbus connection is made
via M12 plug connectors at the
electronics cover.
M12 plug connector for:
• Fieldbus connection
X4233_1, X4233_2
• Digital inputs/outputs
X5133_1, X5133_2,
X5133_3
X5133_1
X5133_2
X5133_3
X4233_1
X4233_2
33710485643
DFC.1..
DSI.1..
• Fieldbus connection is made
via mini I/O plug connectors at
the connection unit.
M12 plug connector for:
• Digital inputs/outputs
X5133_1, X5133_2,
X5133_3
X5133_1
X5133_2
X5133_3
33710516747
27803899/EN – 02/2023

3
Device structure
Example nameplate and type designation of electronics
Operating Instructions – MOVIMOT® advanced 19
3.3 Example nameplate and type designation of electronics
3.3.1 Inner nameplate of DSI.. electronics cover
The following figure gives an example of a nameplate of the electronics cover. For the
structure of the type designation, refer to chapter "Type designation of the electronics
cover".
Eingang/ Input
U =AC 380Y/200...
500Y/289 V
I =
f = AC 5.0A 50..60Hz
T =-25..+35°C IE2 2.1%
03 Status: 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00
U = 3x0..Uinput
I = AC 5.5A
AC 16.0AImax=
f = 0...599Hz
Ausgang/ Output
Type: DSI20A-0055-503-A-T00-001/B
S0#: 01.1234567890.0001.22
D-76646 Bruchsal
Made in Germany
UK WF6 1GX Normanton
ML
[1]
[2]
54043223787645835
[1] Type designation of the electronics cover
[2] Unique serial number of the electronics cover
DataMatrix code with the unique serial number of the electronics cover
3.3.2 Outer nameplate of DSI.. electronics cover
The following figure gives an example of a nameplate of the electronics cover. For the
structure of the type designation, refer to chapter "Type designation of the electronics
cover".
01
FS

EBCM
DSI10A-0020-503-A-S00-000/B
EtherCAT / SBusPLUS
F-ERR F-RUN ERR RUN L/A L/A
DRIVE
[1]
Digital Services
[3][2] [4]
27021630753723019
[1] Type designation of the electronics cover
[2] Identification of the optional HV brake control /B
[3]
Digital Services
Product label with QR code. The QR code can be scanned. You
will be redirected to the digital services of SEW‑EURODRIVE.
There, you have access to product-specific data, documents, and
further services.
In the "Documentation" > "Data and documents" area, the
product manual of the device with further information is avail-
able.
[4] FS logo
27803899/EN – 02/2023

3Device structure
Example nameplate and type designation of electronics
Operating Instructions – MOVIMOT® advanced
20
3.3.3 Type designation DSI.. electronics cover
The following table shows the type designation of the electronics cover:
DSI Product family
DSI = Electronics cover Direct System bus Installation
1 Type communication
1 = EtherCAT®/SBusPLUS
0 Connection configuration
0 = M12-plug connector for digital inputs/outputs and fieldbus
1 = M12 plug connector for digital inputs/outputs1).
2 = Without M12 connector2)
A Communication version
–
0020 Nominal output current of the electronics cover
0020 = 2.0A
0025 = 2.5A
0032 = 3.2A
0040 = 4.0A
0055 = 5.5A
0070 = 7.0A
0095 = 9.5A
0125 = 12.5A
0160 = 16.0A
–
5 Connection voltage
5 = AC 500V
0 Power section design EMC
0 = Basic interference suppression
1 = IT system design
3 Connection type
3 = 3-phase
–
A Version
–
S Device variant
S = System bus profile3)
E = CiA402 device profile (DS402)
0 Technology level
0 = Technology level 0 (standard)
27803899/EN – 02/2023