SEW-Eurodrive MOVIMOT MM D Series User manual

*28503473_0420*
Drive Technology \ Drive Automation \ System Integration \ Services
Operating Instructions
Decentralized Drive Systems
Explosion-Protected MOVIMOT® MM..D Drives
with 3D Category EDRN.. AC Motors
Edition 04/2020 28503473/EN

SEW-EURODRIVE—Driving the world

Contents
Operating Instructions – Explosion-Protected MOVIMOT® MM..D Drives 3
Contents
1 Valid components..................................................................................................................... 6
1.1 1400 min-1 W3 × 400 – 500V (400V)...........................................................................6
1.2 2900 min-1 m3 × 400 – 500V (400V) ..........................................................................6
1.3 Fieldbus interfaces in category 3D (zone 22)1)  ..............................................................7
1.4 Setpoint converter MLA12A in category 3D....................................................................7
2 General information.................................................................................................................. 8
2.1 About this documentation ...............................................................................................8
2.2 Structure of the safety notes ...........................................................................................8
2.3 Decimal separator in numerical values .........................................................................10
2.4 Rights to claim under limited warranty ..........................................................................10
2.5 Other applicable documentation ...................................................................................10
2.6 Product names and trademarks....................................................................................10
2.7 Copyright notice ............................................................................................................10
3 Safety notes ............................................................................................................................ 11
3.1 Preliminary information .................................................................................................11
3.2 Duties of the user..........................................................................................................11
3.3 Target group .................................................................................................................12
3.4 Designated use .............................................................................................................12
3.5 Functional safety technology ........................................................................................13
3.6 Transportation/storage..................................................................................................13
3.7 Installation/assembly.....................................................................................................14
3.8 Electrical installation .....................................................................................................14
3.9 Protective separation ....................................................................................................14
3.10 Startup/operation ..........................................................................................................15
4 Unit design .............................................................................................................................. 16
4.1 MOVIMOT® drive .........................................................................................................16
4.2 MOVIMOT® inverter .....................................................................................................17
4.3 Fieldbus interfaces........................................................................................................19
4.4 MOVIMOT® drive type designation ..............................................................................21
4.5 MOVIMOT® inverter type designation ..........................................................................22
4.6 Type designation of fieldbus interfaces.........................................................................24
4.7 Type designation of module terminal box .....................................................................25
4.8 Identification of explosion-protected drives...................................................................25
5 Mechanical installation .......................................................................................................... 28
5.1 Installation notes ...........................................................................................................28
5.2 Tools required ...............................................................................................................28
5.3 Installation requirements...............................................................................................28
5.4 Installation of MOVIMOT® gearmotor...........................................................................29
5.5 Setpoint converter MLA12A installation ........................................................................31
5.6 Tightening torques ........................................................................................................31
6 Electrical installation.............................................................................................................. 34
6.1 Installation notes ...........................................................................................................34
6.2 Installation instructions..................................................................................................34
28503473/EN – 04/2020

Contents
Operating Instructions – Explosion-Protected MOVIMOT® MM..D Drives
4
6.3 Protection concept ........................................................................................................44
6.4 Connecting MOVIMOT® in conjunction with a fieldbus interface .................................44
6.5 Connection of MOVIMOT® options ..............................................................................52
6.6 Connection of the RS485 bus master ...........................................................................55
7 Startup ..................................................................................................................................... 56
7.1 General information concerning startup........................................................................56
7.2 Requirements................................................................................................................57
7.3 Description of the controls ............................................................................................57
7.4 Description of the DIP switches S1...............................................................................59
7.5 Description of DIP switches S2.....................................................................................60
7.6 Selectable additional functions MM..D-503-14 ............................................................60
7.7 Startup with binary control ............................................................................................64
7.8 Startup with MLA12A setpoint converter.......................................................................67
8 "Easy" startup with RS485 interface/fieldbus...................................................................... 70
8.1 General information concerning startup........................................................................70
8.2 Requirements................................................................................................................71
8.3 Startup procedure .........................................................................................................71
8.4 Coding of process data .................................................................................................73
8.5 Function with RS485 master.........................................................................................81
8.6 Startup with MFP PROFIBUS interface ........................................................................86
8.7 Function of MFP PROFIBUS interface .........................................................................89
9 "Expert" startup with parameter function ............................................................................ 92
10 Operation................................................................................................................................. 93
10.1 Operating notes ............................................................................................................93
10.2 Operating display ..........................................................................................................94
10.3 Drive ID module ............................................................................................................94
11 Service..................................................................................................................................... 96
11.1 Status and error display ................................................................................................96
11.2 Inspection and maintenance .......................................................................................102
11.3 Unit replacement.........................................................................................................103
11.4 Electronics Service by SEW‑EURODRIVE.................................................................105
11.5 Shutdown ....................................................................................................................105
11.6 Storage .......................................................................................................................105
11.7 Extended storage........................................................................................................105
11.8 Waste disposal............................................................................................................106
12 Technical data....................................................................................................................... 107
12.1 Motor with operating point 400V/50Hz or 400V/100Hz..........................................107
12.2 Technical data of option MLA12A 3D .........................................................................110
12.3 Integrated RS485 interface .........................................................................................110
12.4 Diagnostic interface ....................................................................................................111
12.5 Assignment of the drive ID module .............................................................................111
12.6 Permitted operating modes.........................................................................................111
12.7 Overhung and axial loads for motor shaft ends ..........................................................114
12.8 Permitted rolling bearing types ...................................................................................118
28503473/EN – 04/2020

Contents
Operating Instructions – Explosion-Protected MOVIMOT® MM..D Drives 5
12.9 Lubricant tables...........................................................................................................119
12.10 Order information for lubricants, anti-corrosion agents and sealants .........................119
12.11 Operating characteristics ............................................................................................120
12.12 Braking torque assignment .........................................................................................121
12.13 Braking work, working air gap, and brake lining carrier thickness ..............................121
12.14 Resistance and assignment of the brake coil .............................................................121
12.15 Assignment of internal braking resistors .....................................................................122
12.16 PROFIBUS interface MFP21D/Z21D/3D ....................................................................122
13 Declaration of conformity .................................................................................................... 124
Index ...................................................................................................................................... 126
28503473/EN – 04/2020

1Valid components
1400 min-1 3 × 400 – 500V (400V)
Operating Instructions – Explosion-Protected MOVIMOT® MM..D Drives
6
1 Valid components
INFORMATION
These operating instructions apply to the following MOVIMOT® drives:
1.1 1400 min-1 W3 × 400 – 500V (400V)
1400 min-1
3 × 400 –
500V
(400V)
Type PNMNMA/MNnNIline cos φ Brake MB
kW Nm Nm min-1 A Nm
EDRN71MS4../MM03/3D 0.25 1.7 1.8 1400 1.0 0.99 BE05 3.5
EDRN71M4../MM05/3D 0.37 2.5 1.8 1400 1.3 0.99 BE1 5
EDRN80MK4../MM07/3D 0.55 3.75 1.8 1400 1.6 0.99 BE1 7
EDRN80M4../MM11/3D 0.75 5.1 1.8 1400 1.9 0.99 BE2 10
EDRN90S4../MM15/3D 1.1 7.5 1.8 1400 2.4 0.99 BE2 14
EDRN90L4../MM22/3D 1.5 10.2 1.8 1400 3.5 0.99 BE2 14
EDRN100LS4../MM30/3D 2.2 15 1.8 1400 5.0 0.99 BE5 28
EDRN100L4../MM40/3D 3.0 20.5 1.8 1400 6.7 0.99 BE5 28
1.2 2900 min-1 m3 × 400 – 500V (400V)
2900 min-1
m3 x 400 –
500V
(400V)
Type PNMNMA/MNnNIline cos φ Brake MB
kW Nm Nm min-1 A Nm
EDRN71MS4../MM05/3D 0.37 1.2 1.8 2900 1.3 0.99 BE05 3.5
EDRN71M4../MM07/3D 0.55 1.8 1.8 2900 1.6 0.99 BE1 5
EDRN80MK4../MM11/3D 0.75 2.5 1.8 2900 1.9 0.99 BE1 7
EDRN80M4../MM15/3D 1.1 3.6 1.8 2900 2.4 0.99 BE2 10
EDRN90S4../MM22/3D 1.5 4.9 1.8 2900 3.5 0.99 BE2 14
EDRN90L4../MM30/3D 2.2 7.2 1.8 2900 5.0 0.99 BE2 14
EDRN100LS4../MM40/3D 3.0 9.9 1.8 2900 6.7 0.99 BE5 28
28503473/EN – 04/2020

1
Valid components
Fieldbus interfaces in category 3D (zone 22) in conjunction with MOVIMOT in category 3D (zone 22)
Operating Instructions – Explosion-Protected MOVIMOT® MM..D Drives 7
1.3 Fieldbus interfaces in category 3D (zone 22)1)
Fieldbus
interfaces
in category
3D (zone
22) in
conjunction
with
MOVIMOT
in category
3D (zone
22)
The following figure shows the fieldbus interfaces available in category3D:
MFZ21
MFP21
P R OF I
BU S
PROCESS FIELD BUS
®
9007203048847755
1) In conjunction with MOVIMOT® in category3D (zone 22).
1.3.1 PROFIBUS variants
Fieldbus interface + module terminal box MFP21D/Z21D/3D
Part number 08236801
Connection technology sensors/actuators Terminals
Digital inputs 4
Digital outputs 2
1.4 Setpoint converter MLA12A in category 3D
The following figure shows the setpoint converter MLA12A in category 3D:
Setpoint converter MLA12A
Part number 08232342
The setpoint converter MLA12A in category 3D is
available mounted to the MOVIMOT® connection
box only.
28503473/EN – 04/2020

2General information
About this documentation
Operating Instructions – Explosion-Protected MOVIMOT® MM..D Drives
8
2 General information
2.1 About this documentation
The documentation at hand is the original.
This documentation is an integral part of the product. The documentation is intended
for all employees who perform work on the product.
Make sure this documentation is accessible and legible. Ensure that persons respon-
sible for the systems and their operation as well as persons who work on the product
independently have read through the documentation carefully and understood it. If you
are unclear about any of the information in this documentation or if you require further
information, contact SEW‑EURODRIVE.
2.2 Structure of the safety notes
2.2.1 Meaning of signal words
The following table shows the graduation and meaning of the signal words for safety
notes.
Signal word Meaning Consequences if disregarded
DANGER Imminent hazard Severe or fatal injuries
WARNING Possible dangerous situation Severe or fatal injuries
CAUTION Possible dangerous situation Minor injuries
NOTICE Possible damage to property Damage to the product or its en-
vironment
INFORMATION
ON EXPLO-
SION PROTEC-
TION
Important information about
explosion protection
INFORMATION Useful information or tip: Sim-
plifies handling of the product.
2.2.2 Structure of section-related safety notes
Section-related safety notes do not apply to a specific action but to several actions
pertaining to one subject. The hazard symbols used either indicate a general hazard
or a specific hazard.
This is the formal structure of a safety note for a specific section:
SIGNAL WORD
Type and source of hazard.
Possible consequence(s) if disregarded.
• Measure(s) to prevent the hazard.
28503473/EN – 04/2020

2
General information
Structure of the safety notes
Operating Instructions – Explosion-Protected MOVIMOT® MM..D Drives 9
Meaning of the hazard symbols
The hazard symbols in the safety notes have the following meaning:
Hazard symbol Meaning
General hazard
Warning of dangerous electrical voltage
Warning of hot surfaces
Warning of automatic restart
EX
Note on explosion protection
2.2.3 Structure of embedded safety notes
Embedded safety notes are directly integrated into the instructions just before the de-
scription of the dangerous action.
This is the formal structure of an embedded safety note:
SIGNAL WORD! Type and source of hazard. Possible consequence(s) if disregar-
ded. Measure(s) to prevent the hazard.
28503473/EN – 04/2020

2General information
Decimal separator in numerical values
Operating Instructions – Explosion-Protected MOVIMOT® MM..D Drives
10
2.3 Decimal separator in numerical values
In this document, a period is used to indicate the decimal separator.
Example: 30.5kg
2.4 Rights to claim under limited warranty
Read the information in this documentation. This is essential for fault-free operation
and fulfillment of any rights to claim under limited warranty. Read the documentation
before you start working with the product.
2.5 Other applicable documentation
Also observe the following publication:
• Operating instructions "Explosion-Protected EDR..71–315 AC Motors, EDRN63–
315"
Refer to the corresponding documentation for all further components.
2.6 Product names and trademarks
The brands and product names in this documentation are trademarks or registered
trademarks of their respective titleholders.
2.7 Copyright notice
©2020SEW‑EURODRIVE. All rights reserved. Unauthorized reproduction, modifica-
tion, distribution or any other use of the whole or any part of this documentation is
strictly prohibited.
28503473/EN – 04/2020

3
Safety notes
Preliminary information
Operating Instructions – Explosion-Protected MOVIMOT® MM..D Drives 11
3 Safety notes
3.1 Preliminary information
The following general safety notes serve the purpose of preventing injury to persons
and damage to property. They primarily apply to the use of products described in this
documentation. If you use additional components, also observe the relevant warning
and safety notes.
3.2 Duties of the user
As the user, you must ensure that the basic safety notes are observed and complied
with. Make sure that persons responsible for the machinery and its operation as well
as persons who work on the device independently have read through the documenta-
tion carefully and understood it.
As the user, you must ensure that all of the work listed in the following may be carried
out only by qualified specialists:
• Setup and installation
• Installation and connection
• Startup
• Maintenance and repairs
• Shutdown
• Disassembly
Ensure that the persons who work on the product pay attention to the following regula-
tions, conditions, documentation, and information:
• National and regional safety and accident prevention regulations
• Warning and safety signs on the product
• All other relevant project planning documents, installation and startup instructions,
and wiring diagrams
• Do not assemble, install or operate damaged products
• All system-specific specifications and conditions
Ensure that systems in which the product is installed are equipped with additional
monitoring and protection devices. Observe the applicable safety regulations and leg-
islation governing technical work equipment and accident prevention regulations.
28503473/EN – 04/2020

3Safety notes
Target group
Operating Instructions – Explosion-Protected MOVIMOT® MM..D Drives
12
3.3 Target group
Specialist for me-
chanical work
Any mechanical work may be performed only by adequately qualified specialists. Spe-
cialists in the context of this documentation are persons who are familiar with the
design, mechanical installation, troubleshooting, and maintenance of the product who
possess the following qualifications:
• Qualifications in the field of mechanics in accordance with the national regulations
• Familiarity with this documentation
Specialist for elec-
trotechnical work
Any electrotechnical work may be performed only by electrically skilled persons with a
suitable education. Electrically skilled persons in the context of this documentation are
persons who are familiar with electrical installation, startup, troubleshooting, and main-
tenance of the product who possess the following qualifications:
• Qualifications in the field of electrical engineering in accordance with the national
regulations
• Familiarity with this documentation
Additional qualific-
ations
In addition to that, these persons must be familiar with the valid safety regulations and
laws, as well as with the requirements of the standards, directives, and laws specified
in this documentation.
The persons must have the express authorization of the company to operate, pro-
gram, parameterize, label, and ground devices, systems, and circuits in accordance
with the standards of safety technology.
Instructed persons All work in the areas of transportation, storage, operation and waste disposal must be
carried out by persons who are trained appropriately. The purpose of the training is to
give persons the ability to perform the required tasks and work steps in a safe and cor-
rect manner.
3.4 Designated use
The product is intended for use in industrial and commercial systems.
In the case of installation in electrical systems or machines, it is prohibited to start the
proper operation of the product until it is determined that the machine meets the re-
quirements stipulated in the local laws and directives.
The standards given in the declaration of conformity apply to the product.
INFORMATION
• The motor may only be operated with an inverter when the requirements of the
prototype test certificates, the documentation in hand, and the information on the
nameplate of the motor are adhered to.
• The motor must not be operated in areas/applications that produce strong charges
on the motor housing.
– Example: As a fan motor inside a tube. Dust in the tube can produce a buildup
of static electricity. The dust can ignite as a result of electrostatic discharge.
3.4.1 Lifting applications
The product may not be used for lifting applications or on slopes.
28503473/EN – 04/2020

3
Safety notes
Functional safety technology
Operating Instructions – Explosion-Protected MOVIMOT® MM..D Drives 13
3.4.2 Restrictions under the European WEEE Directive 2012/19/EU
You may use options and accessories from SEW-EURODRIVE exclusively in connec-
tion with products from SEW-EURODRIVE.
3.5 Functional safety technology
The product must not perform any safety functions without a higher-level safety sys-
tem unless explicitly allowed by the documentation.
3.6 Transportation/storage
Inspect the shipment for damage as soon as you receive the delivery. Inform the ship-
ping company immediately about any damage. If the product is damaged, it must not
be assembled, installed or started up.
The lifting eyebolts are designed to carry only the weight of the motor without gear
unit. Tighten installed lifting eyebolts. Mounted gear units have separate suspension
attachments, which must be used according to the gear unit operating instructions
when lifting the gearmotor. Do not mount any additional loads.
The installed lifting eyebolts are in accordance with DIN580. Observe the loads and
regulations specified there. The tension force vector of the slings must not exceed a
45° angle in accordance with DIN580.
If necessary, use suitable, sufficiently dimensioned handling equipment.
Observe the following notes when transporting the device:
• Always use all attachment points if available. The attachment points are designed
to carry only the mass of the product. Severe or fatal injuries. Do not apply any ad-
ditional loads.
• Ensure that the product is not subject to mechanical impact.
If the product is not immediately installed, it must be stored in a dry and dust-free loca-
tion. The product can be stored for up to 9 months without requiring any special mea-
sures before startup. Do not store the product outdoors.
Do not transport or store the product on the fan guard.
28503473/EN – 04/2020

3Safety notes
Installation/assembly
Operating Instructions – Explosion-Protected MOVIMOT® MM..D Drives
14
3.7 Installation/assembly
Note the following points during installation:
• Make sure that the supports are even, the foot and flange mounting is correct and
if there is direct coupling, align with precision.
• Avoid resonance between the rotational frequency and the double supply system
frequency.
• Release brake (for motors with mounted brake).
• Turn the rotor by hand and listen for unusual grinding noise.
• Check the direction of rotation in decoupled state.
• Only install or remove belt pulleys and couplings using suitable devices (heat up).
Cover the belt pulleys and couplings with a touch guard. Avoid unacceptable belt
tension.
• Establish any necessary pipe connections.
• Mounting positions with the shaft end pointing upward must be equipped with a
cover to prevent foreign objects from falling into the fan. Ensure that ventilation
openings are not obstructed and that used air cannot be drawn in again straight
away. The same applies to air from adjacent units.
See also the information in chapter Mechanical installation.
3.7.1 Restrictions of use
The following applications are prohibited unless the device is explicitly designed for
such use:
• Use in areas exposed to harmful oils, acids, gases, vapors, dust, and radiation
• Operation in applications with impermissibly high mechanical vibration and shock
loads in excess of the regulations stipulated in EN61800-5-1
3.8 Electrical installation
Ensure that all of the required covers are correctly attached after carrying out the elec-
trical installation.
Make sure that preventive measures and protection devices comply with the applica-
ble regulations (e.g. EN60204-1 or EN61800-5-1).
3.8.1 Required preventive measure
Make sure that the product is correctly attached to the ground connection.
3.9 Protective separation
The product meets all requirements for protective separation of power and electronics
connections in accordance with EN 61800-5-1. The connected signal circuits must
meet requirements according to SELV (Safety Extra Low Voltage) or PELV (Protective
Extra Low Voltage) to ensure protective separation. The installation must meet the re-
quirements for protective separation.
28503473/EN – 04/2020

3
Safety notes
Startup/operation
Operating Instructions – Explosion-Protected MOVIMOT® MM..D Drives 15
3.10 Startup/operation
Observe the safety notes in chapters Startup and "Operation"(→293) in this docu-
mentation.
Make sure the connection boxes are closed and screwed before connecting the sup-
ply voltage.
Depending on the degree of protection, products may have live, uninsulated, and
sometimes moving or rotating parts as well as hot surfaces during operation.
When the device is switched on, dangerous voltages are present at all power connec-
tions as well as at any connected cables and terminals. This also applies even when
the product is inhibited and the motor is at standstill.
Do not separate the connection to the product during operation. This may result in
dangerous electric arcs damaging the product.
If you disconnect the product from the voltage supply, do not touch any live compo-
nents or power connections because capacitors might still be charged. Observe the
following minimum switch-off time:
1minute.
Observe the corresponding information signs on the product.
The fact that the operation LED and other display elements are no longer illuminated
does not indicate that the product has been disconnected from the supply system and
no longer carries any voltage.
Mechanical blocking or internal protective functions of the product can cause a motor
standstill. Eliminating the cause of the problem or performing a reset may result in the
drive restarting automatically. If, for safety reasons, this is not permitted for the drive-
controlled machine, first disconnect the product from the supply system and then start
troubleshooting.
Risk of burns: The surface temperature of the product can exceed 60°C during opera-
tion. Do not touch the product during operation. Let the product cool down before
touching it.
28503473/EN – 04/2020

4Unit design
MOVIMOT drive
Operating Instructions – Explosion-Protected MOVIMOT® MM..D Drives
16
4 Unit design
4.1 MOVIMOT® drive
MOVIMOT
drive
The following figure shows an example of a MOVIMOT® drive with helical gear unit:
[1]
[2]
[3]
[4]
3992077451
[1] MOVIMOT® inverter
[2] Connection box
[3] Motor
[4] Helical gear unit
A MOVIMOT® drive is a combination of:
• MOVIMOT® inverter
• Motor
• Gear unit (optional, see gear unit operating instructions)
28503473/EN – 04/2020

4
Unit design
MOVIMOT inverter
Operating Instructions – Explosion-Protected MOVIMOT® MM..D Drives 17
4.2 MOVIMOT® inverter
MOVIMOT
inverter
The following figure shows the connection box and the MOVIMOT® inverter:
[7][6][5] [7][11]
0 1 2 0 1 2
[5] [12][8] [9] [10]
[4]
[3][1] [2]
N2936
CH01
Type : MM15D-503-00
P# : 18215033
Eingang / Input
U
f
I
T -30. . .+40°C
I3.5A AC 4A AC
f50...60Hz
D-76646 Bruchsal
MOVIMOT
Antriebsumrichter P-Motor 1.5kW / 2HP
Drive Inverter
Made in Germany 2...120Hz
3x0V. . .Uin
U =
=
=
=
=
=
=
3x380. . .500V AC
Ausgang / Output
S# : 1757110
[13] [15][14] [16] [17] [18]
9007199880561035
[1] Connection box
[2] X10: Plug connector for BEM option
[3] Connection plug for the MOVIMOT® inverter
[4] MOVIMOT® inverter with heat sink
[5] Cable glands
[6] Connection unit with terminals
[7] Screw for PE connection
[8] X5, X6: Electronics terminal strips
[9] X1: Connection for brake coil (motors with brake) or braking resistor (motors without brake)
[10] X1: Line connection L1, L2, L3
[11] Connection type identification
[12] Drive ID module
[13] MOVIMOT® inverter nameplate
[14] Setpoint switch f2 (green)
[15] DIP switches S2/5toS2/8
[16] Switch t1 for integrator ramp (white)
[17] DIP switches S1/1toS1/8
[18] DIP switches S2/1toS2/4
28503473/EN – 04/2020

4Unit design
MOVIMOT inverter
Operating Instructions – Explosion-Protected MOVIMOT® MM..D Drives
18
The following figure shows the top side of the MOVIMOT® inverter:
[4]
[3]
[2]
[1]
1 min
28722977291
[1] X50: Diagnostic interface with screw plug
[2] Setpoint potentiometer f1 with screw plug
[3] Status LED
[4] Identification tag
4.2.1 MOVIMOT® device properties
• Frequency inverter with vector-oriented motor control mode
• Power range: 0.25 – 3.0kW
• Voltage range: 3 × 400 – 500V
• Application-specific parameterization is possible
• Pluggable parameter memory for data backup (drive ID module)
• Comprehensive protection and monitoring functions
• Low-noise thanks to PWM switching frequency 16kHz
• Status LED for fast diagnostics
• Diagnostic interface with plug connector as a standard feature
• Diagnostics and manual operation using MOVITOOLS® MotionStudio
• 4Q operation as standard
• Integrated brake management:
– For motors with a mechanical brake, the brake coil is used as the braking resis-
tor.
– For motors without a brake, MOVIMOT® is supplied with an internal braking re-
sistor as standard.
• Is controlled via binary signals, via the serial interface RS485, or optionally with
PROFIBUS.
28503473/EN – 04/2020

4
Unit design
Fieldbus interfaces
Operating Instructions – Explosion-Protected MOVIMOT® MM..D Drives 19
4.3 Fieldbus interfaces
4.3.1 MF.21 fieldbus interface
[1]
[2]
1132777611
[1] Status LEDs
[2] Diagnostic interface (underneath the screw fitting)
INFORMATION
Do not loosen the screw fitting of the diagnostic interface[2] in potentially explosive
atmospheres.
4.3.2 Interface bottom side
[2]
[3]
[1]
1132786955
[1] Connection to connection module
[2] DIP switches (dependent on variant)
[3] Gasket
28503473/EN – 04/2020

4Unit design
Fieldbus interfaces
Operating Instructions – Explosion-Protected MOVIMOT® MM..D Drives
20
4.3.3 Device structure of MFZ connection module
The following figure shows the MFZ connection module.
[3]
[5]
[4]
[3]
[4]
[2]
[3]
[1]
9007200390917003
[1] Terminal strip X20
[2] Isolated terminal block for 24 V through-wiring
(NOTICE: Do not use for shielding.)
[3] M20 cable gland
[4] M12 cable gland
[5] Grounding terminal
The scope of delivery includes 2 EMC cable glands.
28503473/EN – 04/2020