Shark S4701 Series User manual

S4701 Series
OWNER’S GUIDE

11-800-798-7398
WHEN USING YOUR SHARK®2-IN-1
BLAST & SCRUB STEAM POCKET®MOP,
BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED, INCLUDING THE
FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING
YOUR SHARK 2-IN-1 BLAST & SCRUB
STEAM POCKET MOP.
WARNING: DANGER OF SCALDING.
The steam emitted from the Steam Mop
is very hot and may cause scalding.
Please use caution when using the
Steam Mop.
WARNING: KEEP STEAM MOP AWAY
FROM CHILDREN.
POLARIZED PLUG:
This Steam Mop has a polarized plug (one
blade is wider than the other). As a safety
feature, this plug will fit into a polarized outlet
only one way. If the plug does not fit fully
into the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician. Do not
attempt to defeat this safety feature.
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
1. CAUTION: When in use, never turn the
Steam Mop over or on its side. Never direct
steam toward people, pets, or plants.
2. Always unplug and allow the Steam Mop to cool
before attaching or removing accessories.
3. Use the Steam Mop only for its intended use.
4. DO NOT use for space-heating purposes.
5. DO NOT use outdoors.
6. DO NOT leave the Steam Mop unattended
when plugged in. Always unplug the power cord
from the electrical outlet when not in use and
beforeservicing.
7. DO NOT allow the Steam Mop to be used by
children. Close attention is necessary when
used near children, pets, or plants.
8. Use only as described in this manual.
9. Use only manufacturer’s recommended
accessories.
10. DO NOT use with damaged cord or plug. If
Steam Mop is not working as it should or has
been dropped, damaged, left outdoors, or
dropped into water, return it to EURO-PRO
Operating LLC for examination and repair.
Incorrect re-assembly or repair can cause a risk
of electrical shock or injury to persons when the
Steam Mop is used.
11. To protect against a risk of electric shock, DO
NOT immerse the Steam Mop in water or any
other liquids.

2www.sharkclean.com
12. DO NOT handle plug or Steam Mop with wet
hands or operate the Steam Mop without
wearing shoes.
13. DO NOT pull or carry by cord, use cord as
a handle, close a door on cord, or pull cord
around sharp edges or corners. Do not run
Steam Mop over cord. Keep cord away from
heated surfaces.
14. DO NOT unplug by pulling on power cord. To
unplug, grasp the plug not the power cord.
Do not use extension cords or outlets with
inadequate current-carrying capacity.
15. DO NOT put any objects into the the Steam
Nozzle openings. Discontinue use if the steam
nozzle is blocked.
16. DO NOT put hands or feet under the Steam
Mop—it gets very hot.
17. When mopping, use ONLY on flat, horizontal
surfaces. Do not use on walls, counters,
orwindows.
18. DO NOT use on leather, wax-polished furniture,
synthetic fabrics, velvet, or other delicate,
steam-sensitive materials.
19. DO NOT use on electronics, such as televisions,
video game consoles, and cable boxes.
20. DO NOT add cleaning solutions, vinegar,
scented perfumes, oils, or any other chemicals
to the water used in the Steam Mop as this
may damage it or make it unsafe for use. If you
live in a hard-water area, we recommend using
distilled water in your Steam Mop.
21. Never leave any wet Cleaning Pad in one
spot while using or storing for any period of
time, as this may damage your surfaces.
22. Carefully remove all Cleaning Pads after you have
unpluged and allowed the Steam Mop to cool.
23. When cleaning the exterior of the Steam Mop,
unplug the power cord from the electrical outlet
and clean with a dry or damp cloth. Do not pour
water or use alcohol, benzene, or paint thinner on
the
Steam Mop .
24. Extreme caution should be exercised when
using the Steam Mop to clean stairs.
25. Keep your work area well lit.
26. Store Steam Mop indoors in a cool, dry place.
27. To avoid circuit overload, do not operate another
appliance on the same socket (circuit) as the
Steam Mop.
29. To avoid scalding injuries, always unplug and
allow the Steam Mop to cool before removing or
changing Mop Heads, Accessories, or Cleaning
Pads.
WARNING: Your Steam Mop is
designed to clean hard-floor surfaces that will
withstand high heat. Do not use on unsealed
wood or unglazed ceramic floors. On surfaces
that have been treated with wax and on some
no-wax floors, the sheen may be removed
by the heat and steam action. It is always
recommended to test an isolated area of the
surface to be cleaned before proceeding. We
also recommend that you check the use and
care instructions from the floor manufacturer.
SAVE THESE
INSTRUCTIONS

31-800-798-7398
Thank you for purchasing the Shark®2-in-1 Blast & Scrub Steam Pocket®Mop.
This Owner’s Guide is designed to help you get a complete understanding of your new Steam Mop. Please read it
carefully and keep for future reference.
For a list of what is included with this model, refer to inside flap of box.
If you should have a question about your Shark®2-in-1 Blast & Scrub Steam Pocket®Mop, please call Shark
Customer Service at 1-800-798-7398.
REGISTER YOUR PURCHASE:
www.sharkclean.com
1-800-798-7398
RECORD THIS INFORMATION:
Model Number: ____________________________________
Date of Purchase (Keep receipt):_________________________
TECHNICAL SPECIFICATIONS:
Voltage: 120 V., 60 Hz
Watts: 1200W
Water Capacity: 410 ml (13 oz.)

4www.sharkclean.com
Contents
Getting Started............................................................................................... 5
Assembling Your Steam Mop .......................................................................... 7
Using Your Steam Mop ................................................................................... 8
Using Your Handheld Steamer........................................................................10
Using the Precision Clean Pocket Accessory..............................................12
Using the Total Clean Pocket Accessory.....................................................12
Using the Scrub Blast Accessory ...............................................................13
Using the EZ Reach Bending Duster Accessory..........................................13
Using the Flat Scrubber Accessory ............................................................14
Using the Steam Duster Accessory............................................................14
Caring for Your Steam Mop............................................................................15
Ordering Optional Accessories .......................................................................17
Troubleshooting Guide ...................................................................................19
Frequently Asked Questions.......................................................................... 21
Warranty...................................................................................................... 22
Thank you for
purchasing the
Shark®2-in-1
Blast & Scrub
Steam Pocket®
Mop.

51-800-798-7398
Getting Started
When assembling your Steam Mop there may be a little water in or around the water tank. This is because we test all
our Steam Mops before you buy them, so you get a quality Shark®2-in-1 Blast & Scrub Steam Pocket®Mop.
a Mop Handle
bQuick-Release Swivel Cord Wrap
cCord Management Clip
dEngage Scrubber/Release Head
eSteam Control Button
fWater Tank Lid
gWater Tank
hMop Body
iSteam Control Button for Above-Floor Mode
jStain Scrubber
kSteam Nozzle
lRectangle Mop Head
mPocket Pad for Rectangle Mop Head
nFilling Flask
a
f
g
h
j
i
d
c
b
l
k
m n
e

6www.sharkclean.com
HANDHELD ACCESSORIES
ACCESSORY HOSE
The Shark®2-in-1 Blast & Scrub Steam Pocket®Mop comes
with an assortment of accessories that easily attach to the
Accessory Hose for optimal range and mobility.
SCRUB BLAST ACCESSORY & PAD
Ideal for large, flat surfaces.
Do not use without the Scrub Blast Pad attached.
TOTAL CLEAN POCKET ACCESSORY & PAD
Ideal for flat surfaces, corners, and edges.
Do not use without a Total Clean Pocket Pad attached.
PRECISION CLEAN POCKET ACCESSORY & PAD
Ideal for small uneven surfaces, corners, and edges.
Do not use without a Precision Clean Pocket Pad attached.
EZ REACH BENDING STEAM DUSTER & PAD
Ideal for cleaning and dusting a variety of surfaces, like large
areas, especially hard-to-reach places, and crevices.
Do not use without the EZ Reach Bending Steam Duster
Padattached.
FLAT SCRUBBER ACCESSORY & PAD
Ideal for dusting a variety of surfaces, especially hard-to-
reach ones.
Do not use without the Flat Scrubber Pad attached.
STEAM DUSTER ACCESSORY & PAD
Ideal for cleaning and dusting a variety of surfaces, like large
areas, hard-to-reach places, and crevices.
Do not use without the Steam Duster Padattached.
For a full list of what is included with your Steam Mop, please refer to the inside flap of your box.
CAUTION: Test in a small inconspicuous area and contact your surface manufacturer/installer for
specific information on your surface.

71-800-798-7398
Assembling Your Steam Mop
fig. 1 fig. 2
WARNING: Always make sure the Steam Mop
is UNPLUGGED from the wall when not in use.
Never fill the Steam Mop, attach the Mop Head,
or change or remove the Pocket Pad when the
Steam Mop is plugged into the wall. Unplug from
the wall and allow to cool before you fill the
Steam Mop, attach or remove the Mop Head, or
change or remove the Cleaning Pad. To prolong
the life of your Steam Mop, we recommend using
distilled water. Make sure you add only water
to the tank. Chemicals or cleaning solutions
(including vinegar) may damage the Steam Mop
and could be unsafe for you and your family.
STEAM MOP ASSEMBLY
1Insert the Mop Handle into the Mop Body. (fig. 1) Push
the Mop Handle in until you hear it click into place.
2Select the Rectangle Mop Head and Pocket Pad. If
the Pocket Pad is not already attached, fit one side
of the Pocket Pad onto the Mop Head first, then,
using the loop, pull the Pocket Pad over the Mop
Head. Attach the hook-and-loop fasteners on the top
of the Pocket Pad to secure it in place.
3Insert the Mop Head into the Mop Body. Push until
you hear it click into place (fig. 2).
4Attach the Scrubbing Pad to the hook-and-loop
surface of the Stain Scrubber (fig. 3).
5Pull up on the Water Tank Cap to open (fig. 4).
6Use the Filling Flask to pour water into the Water
Tank (fig. 5). Do not overfill. Press the Water Tank
Cap firmly to close it.
NOTE: Steps 2–6 also apply to the Triangle Mop Head.
NOTE: The Triangle Mop Head may not be included
with your product. See box for specific product details.
fig. 4
fig. 5
fig. 3

8www.sharkclean.com
NOTE: To prolong the life of your Steam Mop, we
recommend using distilled water.
NOTE: Sweep or vacuum your floors prior to
cleaning with your Steam Mop.
1Pull and twist the Quick-Release Cord Holder to
unwrap the power cord completely (fig. 6). Plug into
an electrical outlet.
2The Steam Mop will be in Standby Mode as soon as it
is plugged in. The Standby Mode can be identified by a
blinking light around the Steam Control Button (fig. 7).
3Press the Steam Control Button to select either the LO or
HI Setting (the ACCESSORY Setting is not available for
floor cleaning) (fig. 7).Press once for the low setting, twice
for HI, and three times to return to Standby Mode. Once in
Standby Mode, a light will blink around the Steam Control
Button, but all other Steam Setting Lights will be off.
4Clean your floors with a forward and backward motion.
5
When you come to a tough, dried-on floor stain, use
the Steam Blast Scrub Mode to clean it away.
IMPORTANT: Make sure you do not use the Steam Mop without attaching a Pocket Pad and adding water
to the Water Tank first. When you are using the Steam Mop for the first time, it might take longer than
the normal 30 seconds to start steaming.
IMPORTANT: Do not use on unsealed wood or unglazed ceramic floors. On surfaces that have been treated
with wax and on some no-wax floors, the sheen may be removed by the heat and steam action. Test an
isolated area of the surface to be cleaned before proceeding. Check the use and care instructions from the
floor manufacturer.
Using Your Steam Mop
6To engage the Steam Blast Scrub Mode, slide the
Engage Scrubber/Release Head Button all the
way down until you hear a click (fig. 8). The Stain
Scrubber will automatically pop into position. Lift
the Mop Body off the Mop Head and place the Stain
Scrubber on the floor to start scrubbing.
CAUTION: While in Scrub Blast Mode, do not
leave the Steam Mop stationary.
CAUTION: Do not Scrub any one area for an
extended period of time.
7To go back to mopping, re-dock the Mop Body onto
the Mop Head. The Stain Scrubber will automatically
retract.
8When you are done mopping, press the Steam
Control Button until you return to Standby Mode.
9When the Water Tank is empty, the Steam Mop will stop
producing steam. You can refill the Water Tank at any
time as long as the Steam Mop is unplugged. Follow the
Water Tank filling instructions on page 7.
NOTE: Please wait 2 to 3 minutes for the Steam
Mop to cool off before switching the Mop Head or
Cleaning Pad. Never leave the Steam Mop with a
damp/wet Cleaning Pad on any floor.
fig. 6
fig. 7
fig. 8

91-800-798-7398
The Shark®2-in-1 Blast & Scrub Steam Pocket®Mop has Intelligent steam settings that allow you to select the right
amount of steam for your floors and produces greater steam for your accessories. See below for tips on when to use
each setting.
Using Your Steam Mop - continued
SETTING IDEAL FOR THESE SURFACES RECOMMENDED USAGE
Laminate
Hardwood
Marble
Cleaning delicate surfaces
Light cleaning and dusting
Loosening and lifting light dirt
Sanitizing floors
Hardwood
Marble
Tile
Stone
Cleaning most surfaces and large areas
Basic, everyday cleaning
Removing spots and smaller messes
Cleaning moderate- and heavy-traffic areas
Sanitizing floors
Sealed above-floor hard surfaces
around the house Dusting or cleaning above-floor sealed hard surfaces.
SCRUB BLAST
LO HI
To engage the Scrub Blast Mode, slide the Engage Scrubber/Release Head Button down until
you hear a click. The Stain Scrubber will automatically pop in to position. Lift the Mop body off
the Mop Head and place the Stain Scrubber on the floor to start scrubbing. You can select your
preferred level of steam. Use LO Setting for low-moisture scrubbing. Use the HI Setting for
stubborn, stuck-on stains.
TO SANITIZE* WITH THE RECTANGLE MOP HEAD
1 Start with a clean Pocket Pad.
2Plug in the unit and press the Steam Control Button to select either the LO or HI Setting.
3Wait 30 seconds for the unit to begin producing steam.
4Start mopping on an appropriate sealed hard-floor surface with a forward and backward motion. After three minutes,
your unit is ready to be used to sanitize.
5Using a forward and backward motion, move the unit over the area you seek to sanitize. Repeat at least 15 times.
* Sanitization studies were conducted under controlled test conditions. Household conditions and results may vary.
With Rectangle Mop Head only. Not with Above-Floor Accessories or in Blast & Scrub mode.

10www.sharkclean.com
Your Shark®Steam Blast 2-in-1 Steam Pocket®
Mop can be converted to a Handheld Steamer that is
designed to clean surfaces that can withstand high heat
and moisture. Do not use on unsealed wood surfaces
(especially antique wood furniture), unglazed ceramic
tile, painted surfaces, or surfaces that have been
treated with wax, oils, varnishes, or shellac. The sheen
may be removed by the heat, steam, and friction of the
cleaning Accessories. It is always recommended to test
an isolated area of the surface to be cleaned before
proceeding.
We also recommend you check the use and care
instructions from the surface manufacturer.
When cleaning finished wood surfaces, use broad,
continuous strokes. To prevent surface damage, avoid
focusing steam or allowing the cleaning Accessories to
remain stationary in any one spot.
Using Your Handheld Steamer
CAUTION: To avoid scalding injuries, always
unplug and allow the Steam Mop to cool before
transitioning it to the Handheld Steamer.
1To transition the Handheld Steamer, press and hold
down the Handle Release Button while pulling out
the Mop Handle (fig. 9).
2To remove the Mop Head, press down on the
Engage Scrubber/Release Head Button and lift the
Mop Body off the Mop Head (fig. 10).
NOTE: When you remove the Mop Handle, steam
will automatically stop.
NOTE: Do not leave the wet Mop Head on any floor
for a prolonged period of time.
fig. 9
fig. 10
NOTE: To ensure constant steam flow, make sure
the Steam Nozzle is not facing upward.

11 1-800-798-7398
5To remove the Accessory Hose, press and hold
down the Hose Release Button, then slide out the
Accessory Hose.
3First attach the Accessory Hose to the Handheld
Steamer by snapping the Accessory Hose into the
Steam Nozzle (fig. 11).
4Select the desired cleaning accessory. Follow
the Accessory sub-assembly instructions (pages
12–14). Then insert the Direct Steam Nozzle into the
Accessory (fig. 12).
Using Your Handheld Steamer - continued
fig. 11
Hose Release Button
Direct Steam
Nozzle
EZ Reach Bending Duster Accessory
Steam Duster Accessory
Flat Scrubber Accessory
Scrub Blast Accessory
Total Clean Pocket Accessory
Precision Clean Pocket Accessory
CAUTION: Make sure the Steam Mop is
unplugged or in Standby Mode while
attaching or removing the Accessory Hose
from the Steam Nozzle.
Handheld Steamer
Accessory Release
Buttons
Accessory Hose
NOTE: Some accessories may not be included with your
product. See box for specific product details.
fig. 12

12www.sharkclean.com
USING THE TOTAL CLEAN POCKET ACCESSORY
Cleaning Tip: The Total Clean Pocket Accessory is ideal
for large, flat surfaces. The pointed tip is great for edges
and corners.
CAUTION: Make sure the Steam Mop is
unplugged or in Standby Mode while attaching
or removing the Total Clean Pocket Accessory.
Avoid touching the Accessory, as it will be very
hot after steaming.
CAUTION: To avoid scalding injuries, always unplug
and allow the Steam Mop to cool before removing
or changing Accessories or Cleaning Pads.
CAUTION: Do not use on wallpaper.
1Slide the Total Clean Pocket Pad over the Total Clean
Pocket Accessory so it fits snuggly.
2Cinch the elastic band and slide the locking toggle
to tighten.
3Attach the Total Clean Pocket Accessory by
connecting it to the Direct Steam Nozzle until it clicks
into place.
4When you press the Steam Control Button Accessory
Mode (ACCESSORY) will automatically be selected
and you can begin cleaning (LO and HI Settings are
not available for above-floor cleaning).
5To remove the Total Clean Pocket Accessory,
squeeze the Accessory Release Buttons, then slide
out the Accessory.
USING THE PRECISION CLEAN POCKET ACCESSORY
Cleaning Tip: The Precision Clean Pocket Accessory is
ideal for small, uneven surfaces. The pointed tip is great for
edges and corners.
CAUTION: Make sure the Steam Mop is
unplugged or in Standby Mode while attaching
or removing the Precision Clean Pocket
Accessory. Avoid touching the Accessory, as it
will be very hot after steaming.
CAUTION: To avoid scalding injuries, always unplug
and allow the Steam Mop to cool before removing
or changing Accessories or Cleaning Pads.
CAUTION: Do not use on wallpaper.
1Slide the Precision Clean Pocket Pad over the
Precision Clean Pocket Accessory so it fits snuggly.
2Cinch the elastic band and slide the locking toggle
to tighten.
3Attach the Precision Clean Pocket Accessory by
connecting it to the Direct Steam Nozzle until it clicks
into place.
4When you press the Steam Control Button Accessory
Mode (ACCESSORY) will automatically be selected
and you can begin cleaning (LO and HI Settings are
not available for above-floor cleaning).
5To remove the Precision Clean Pocket Accessory,
squeeze the Accessory Release Buttons, then slide
out the Accessory.

13 1-800-798-7398
USING THE EZ REACH BENDING DUSTER
ACCESSORY
Cleaning Tip: The EZ Reach Bending Duster Accessory is
ideal for dusting a variety of surfaces, especially hard-to-
reach ones .
CAUTION: Make sure the Steam Mop is
unplugged or in Standby Mode while attaching
or removing the EZ Reach Bending Duster
Accessory. Avoid touching the Accessory, as it
will be very hot after steaming.
CAUTION: To avoid scalding injuries, always unplug
and allow the Steam Mop to cool before removing
or changing Accessories or Cleaning Pads.
CAUTION: Make sure ceiling fans are off before
cleaning/dusting them.
1Slide the EZ Reach Bending Duster Pad all the way up the
EZ Reach Bending Duster Accessory so it fits snuggly.
2Cinch the elastic band and slide the locking toggle
to tighten.
3Attach the EZ Reach Bending Duster Accessory
by connecting it to the Direct Steam Nozzle until it
clicks into place.
4When you press the Steam Control Button Accessory
Mode (ACC) will automatically be selected and you
can begin cleaning (LO and HI Settings are not
available for above-floor cleaning).
5To bend the accessory into the desired position, pull
back on the buttons on the sides of the EZ Reach
Bending Duster Accessory.
6To remove the EZ Reach Bending Duster Accessory,
squeeze the Accessory Release Buttons, then slide
out the Accessory.
USING THE SCRUB BLAST ACCESSORY
Cleaning Tip: The Scrub Blast Accessory is ideal for
large, flat surfaces. Its design allows you to apply more
force when scrubbing, which redistributes the steam
toward the Cleaning Pad when pressed against a surface.
CAUTION: Make sure the Steam Mop is unplugged
or in Standby Mode while attaching or removing
the Scrub Blast Accessory. Avoid touching the
Accessory, as it will be very hot after steaming.
CAUTION: To avoid scalding injuries, always unplug
and allow the Steam Mop to cool before removing
or changing Accessories or Cleaning Pads.
CAUTION: Do not use on wallpaper.
CAUTION: This is not an iron. Do not use on
garments or soft surfaces. It may result in damage.
1To attach the Scrub Blast Pad, place it exterior side
down on a flat surface, then set the Scrub Blast
Accessory into the inside of it. Pull the Pad over the
edges of Accessory until it fits snuggly.
2Attach the Scrub Blast Accessory by connecting it to
the Direct Steam Nozzle until it clicks into place.
3When you press the Steam Control Button Accessory
Mode (ACCESSORY) will automatically be selected
and you can begin cleaning (LO and HI Settings are
not available for above-floor cleaning). Steam will
blast from the front tip of the Accessory—press the
Accessory against the surface you wish to clean,
and the steam will redirect into the Pad. Continue to
press the Accessory down as you clean.
4To remove the Scrub Blast Accessory, squeeze the
Accessory Release Buttons, then slide out the
Accessory.
Using Your Handheld Steamer - continued

14www.sharkclean.com
USING THE STEAM DUSTER ACCESSORY
Cleaning Tip: The Steam Duster Accessory is ideal for
cleaning and dusting a variety of surfaces, like large areas,
hard-to-reach places, and crevices.
CAUTION: Make sure the Steam Mop is unplugged
or in Standby Mode while attaching or removing
the Steam Duster Accessory. Avoid touching the
Accessory, as it will be very hot after steaming.
CAUTION: To avoid scalding injuries, always unplug
and allow the Steam Mop to cool before removing
or changing Accessories or Cleaning Pads.
1Slide the Steam Duster Pad all the way up the Steam
Duster Accessory so it fits snuggly.
2Cinch the elastic band and slide the locking toggle to
tighten.
3Attach the Steam Duster Accessory by connecting it
to the Direct Steam Nozzle until it clicks into place.
4When you press the Steam Control Button Accessory
Mode (ACCESSORY) will automatically be selected
and you can begin cleaning (LO and HI Settings are
not available for above-floor cleaning).
5 To remove the Steam Duster Accessory, squeeze
the Accessory Release Buttons, then slide out the
Accessory.
USING THE FLAT SCRUBBER ACCESSORY
Cleaning Tip: The Flat Scrubber Accessory is ideal for
a variety of surfaces. Its design allows you to apply more
force when scrubbing.
CAUTION: Make sure the Steam Mop is
unplugged or in Standby Mode while attaching
or removing the Flat Scrubber Accessory.
Avoid touching the Accessory, as it will be
very hot after steaming.
CAUTION: To avoid scalding injuries, always unplug
and allow the Steam Mop to cool before removing
or changing Accessories or Cleaning Pads.
CAUTION: Do not use on wallpaper.
1To attach the Flat Scrubber Pad, place it exterior side
down on a flat surface, then set the Flat Scrubber
Accessory into the inside of it. Pull the Pad over the
edges of Accessory until it fits snuggly.
2Attach the Flat Scrubber Accessory by connecting it
to the Direct Steam Nozzle until it clicks into place.
3When you press the Steam Control Button Accessory
Mode (ACCESSORY) will automatically be selected
and you can begin cleaning (LO and HI Settings are
not available for above-floor cleaning).
4To remove the Flat Scrubber Accessory, squeeze
the Accessory Release Buttons, then slide out the
Accessory.

15 1-800-798-7398
AFTER USE AND STORAGE
1Press the Steam Control Button until the Steam Mop
returns to Standby Mode. Unplug the cord from the
outlet and place the Steam Mop into the upright
position. Let it cool.
2If you have been using the Handheld Steamer,
reattach it to the Mop Handle.
3 Remove the Pocket Pad from the Mop Head by
undoing the hook-and-loop closure and using the
loop on the side to pull it off the Mop Head, avoiding
contact with the hot Pocket Pad.
Caring for Your Steam Mop
fig. 13
4Empty the Water Tank before storing. Open the
Water Tank Cap and empty the Tank in a sink. Close
the Cap.
5 To store the Steam Mop hanging up, first remove
the Mop Head (after it has cooled and the steam
has been released), then hang on a large hook (not
included) (fig. 13).

16www.sharkclean.com
fig. 15
POCKET PAD CARE INSTRUCTIONS
Care
Before washing, close the hook-and-loop fasteners so they
won’t snag on the Pocket Pads. Machine wash the Pocket
Pads separately with warm water using liquid detergent.
NEVER USE BLEACH, POWDERED DETERGENT, OR
FABRIC SOFTENERS as they may damage or leave a
coating on the Pocket Pads that will reduce their cleaning
performance and absorbancy . Pocket Pads should be
line-dried or tumble-dried on a low setting, as this will
extend the life of the microfiber fabric (fig. 14).
Loose fibers can indicate wearing of the microfiber
fabric. Do not pull the loose fibers as this can cause the
weave to come undone. Simply trim the loose fibers with
scissors (fig. 15).
Caring for Your Steam Mop - continued
fig. 14
Replacement Pocket Pads
For best cleaning results, we recommend replacing your
Pocket Pads every 3 to 4 months following normal use.
As with any fabric, dirt particles, grease, friction, and
repeated washing can cause the fibers to break down, and
you may notice an increase in the effort needed to push or
pull the Steam Mop.
You can purchase replacement Pocket Pads and
Accessories by visiting www.sharkclean.com or calling
1-800-798-7398.
STEAM NOZZLE CARE
If you believe the Steam Nozzle or the Direct Steam
Nozzle is clogged, please contact Customer Service at
1-800-798-7398 or [e-mail].

17 1-800-798-7398
ACCESSORY
Triangle Mop Head
For cleaning corners and hard-to-reach areas (not for sanitization).
101SC4601
Rectangle Mop Head
For all-purpose cleaning.
102SC4601
XL Mop Head
For large-area cleaning (not for sanitization).
100SC4601
Triangle Washable All-Purpose Scrub Pocket Pad
One side features scrubbing strips to help remove tough, dried-on stains; the other
features shaggy fingers to lift and lock in dust and dirt.
P179W
Rectangle Washable All-Purpose Scrub Pocket Pad
One side features scrubbing strips to help remove tough, dried-on stains; the other
features shaggy fingers to lift and lock in dust and dirt.
P139W
XL Rectangle All-Purpose Pocket Pad
Shaggy fingers on both sides lift and lock in dust and dirt.
P180W
NOTE: Select Accessories are included. Others are available for purchase at www.sharkclean.com or
by calling 1-800-798-7398.
For a list of what is included with this model, refer to inside flap of box.
Ordering Optional Accessories

18www.sharkclean.com
ACCESSORY
Scrub Blast Pad
Quilted microfiber deep-cleans hard-to-clean surfaces.
P168W
Total Clean Pocket Pad
One side features a scrubber to help remove stuck-on messes; the other features
quilted microfiber to lift and lock in dust and dirt.
P173W
Precision Clean Pocket Pad
One side features a scrubber to help remove stuck-on messes; the other features
quilted microfiber to lift and lock in dust and dirt.
P171W
EZ Reach Bending Duster Pad & Steam Duster Pad
Extra-large shaggy fingers on both sides lift and lock in dust and dirt.
P170W
Flat Scrubber Pad
Shaggy fingers lift and lock in dust and dirt.
P123W
Stain Blast Scrubber Pad
Breaks apart tough, dried-on stains fast.
P176W

19 1-800-798-7398
Troubleshooting Guide
PROBLEM POSSIBLE REASONS & SOLUTIONS
The Steam Mop isn’t
producing any steam.
The Steam Mop should be securely plugged into an electrical outlet. Check your
fuse or circuit breaker or try a different outlet.
Make sure the Water Tank is full, the unit is plugged in, and the light around the
Steam Control Button is solid.
If the light around the Steam Control Button is not lit, try a different
electricaloutlet.
If the light around the Steam Control Button is blinking, press the Steam Control
Button to select a Steam Setting.
If the light around the Steam Control Button is solid, wait 30 seconds for the unit
to warm up.
If after following the above steps the Steam Mop still does not
produce any steam, contact Customer Service at 1-800-798-7398 or
consumer[email protected].
The Steam Mop is producing
intermittent steam.
This is normal—for more consistent steam select the HI Setting.
Also make sure the Water Tank is full.
I can’t select a Steam Setting.
Make sure the Steam Mop is plugged in and the light around the Steam Control
Button is solid.
If your Steam Mop is producing steam but the light around the Steam Control
Button is not lit, call customer service at 1-800-798-7398
I am getting streaky/cloudy
floors.
The Pocket Pad might be dirty. If it is, flip it over to the clean side or change it
entirely. If you washed the Pocket Pad with powdered detergent, then it could be
damaged and require replacement.
This could also be an indication of soap or grease residue that has accumulated
on the floor. As our Steam Mops use only a small amount of water, it may not
be enough to rinse off the accumulation of residue that the steam is bringing to
the surface. We suggest rinsing the floor with nothing but water, letting it dry,
and then steam mopping again with a clean Pocket Pad. One or more rinses will
generally remove the residue.
A more stubborn case may require you to rinse the floor with a mix of one part
vinegar and two parts water* (but DO NOT put vinegar or any other cleaner into
the Steam Mop’s Water Tank).
*Please consult your flooring manufacturer’s care and maintenance instructions
before applying any cleaning products or solutions including vinegar.