Sharp XL-ES5 User manual

Thank you for purchasing this SHARP product.
To obtain the best performance from this product, please read this
manual carefully. It will guide you in operating your SHARP product.
MICRO COMPONENT SYSTEM
MODEL
XL-ES5
XL-ES50
OPERATION MANUAL
XL-ES5 Micro Component System consisting of XL-ES5 (main unit), CP-
ES5F (front speakers) and CP-ES5SW (subwoofer).
XL-ES50 Micro Component System consisting of XL-ES50 (main unit),
CP-ES50F (front speakers) and CP-ES50SW (subwoofer).
The illustrations printed in this operation manual are for the model XL-
ES50.

2
XL-ES5
XL-ES50
Important Instruction
SPECIAL NOTES
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols:
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s en-
closure that may be of sufficient magnitude
to constitute a risk of electric shock to per-
sons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and main-
tenance (servicing) instructions in the lit-
erature accompanying the appliance.
0012
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE. 0012
Caution - use of controls or adjustments or performance
of procedures other than those specified herein may re-
sult in hazardous radiation exposure. 0012
Note:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency en-
ergy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
●Consult the dealer or an experienced radio/TV technician for help.
WARNING
FCC Regulations state that any unauthorized changes or modifications
to this equipment not expressly approved by the manufacturer could
void the user's authority to operate this equipment.
FOR YOUR RECORDS
Foryourassistanceinreportingthisunitincaseoflossortheft,
pleaserecordbelowthemodel numberandserial numberwhich
are located on the rear of the unit.
Please retain this information.
Model number .......................................................
Serial number .......................................................
Date of purchase .......................................................
Place of purchase .......................................................
0202

3
XL-ES5
XL-ES50
Important Instruction
IMPORTANT SAFETY INSTRUCTIONS
1Read Instructions - All the safety and operating instructions should
be read before the product is operated.
2Retain Instructions - The safety and operating instructions should be
retained for future reference.
3Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4Follow Instructions - All operating and use instructions should be
followed.
5Cleaning - Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
6Attachments - Do not use attachments not recommended by the prod-
uct manufacturer as they may cause hazards.
7Water and Moisture - Do not use this product near water - for ex-
ample, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a
wet basement; or near a swimming pool; and the like.
8Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to
a child or adult, and serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table recommended by the manufac-
turer, or sold with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a mounting ac-
cessory recommended by the manufacturer.
9A product and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces
may cause the product and cart combination to over-
turn.
10 Ventilation - Slots and openings in the cabinet are provided for venti-
lation and to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked or cov-
ered. The openings should never be blocked by placing the product on
a bed, sofa, rug, or other similar surface. This product should not be
placed ina built-in installation suchas abookcaseor rack unless proper
ventilation is provided or the manufacturer’s instructions have been
adhered to.
11 Power Sources - This product should be operated only from the type
of power source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product dealer or
local power company. For products intended to operate from battery
power, or other sources, refer to the operating instructions.
12 Grounding or Polarization - This product may be equipped with a
polarized alternating-current line plug (a plug having one blade wider
than the other). This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
Alternate Warnings - This product is equipped with a three-wire
grounding-type plug, a plug having a third (grounding) pin. This plug
will only fit into a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact your electri-
cian to replace your obsolete outlet. Do not defeat the safety purpose
of the grounding-type plug.
13 Power-Cord Protection - Power-supply cords should be routed so
that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from the product.
14 Protective Attachment Plug - The product is equipped with an at-
tachment plug having overload protection. This is a safety feature. See
Instruction Manual for replacement or resetting of protective device. If
replacement of the plug is required, be sure the service technician has
used a replacement plug specified by the manufacturer that has the
same overload protection as the original plug.

4
XL-ES5
XL-ES50
Important Instruction
IMPORTANT SAFETY INSTRUCTIONS (continued)
15 OutdoorAntenna Grounding - If an outside antenna or cable system
is connected to the product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges and
built-up staticcharges.Article 810oftheNationalElectricalCode,ANSI/
NFPA 70, provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire to an an-
tenna discharge unit, size of grounding conductors, location of antenna
discharge unit, connection to grounding electrodes, and requirements
for the grounding electrode.
16 Lightning - For added protection for this product during a lightning
storm, or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning and
power-line surges.
17 Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits,
or where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be
fatal.
18 Overloading - Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock.
19 Object and Liquid Entry - Never push objects of any kind into this
product through openings as they may touch dangerous voltage points
or short-out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
20 Servicing - Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
21 Damage Requiring Service - Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged,
b)If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d)If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the op-
erating instructions as an improper adjustment of other controls may
result in damage and will often require extensive work by a qualified
technician to restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this
indicates a need for service.
22 Replacement Parts - When replacement parts are required, be sure
the service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
23 Safety Check - Upon completion of any service or repairs to this prod-
uct, ask the service technician to perform safety checks to determine
that the product is in proper operating condition.
24 Wall or Ceiling Mounting - The product should be mounted to a wall
or ceiling only as recommended by the manufacturer.
25 Heat - The product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products (including ampli-
ANTENNA LEAD IN WIRE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELECTRICAL CODE
S2898A
ELECTRIC
SERVICE
EQUIPMENT
GROUND
CLAMP
Example of antenna grounding as per
National Electrical Code, ANSI/NFPA 70
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
fiers) that produce heat.
0304

5
XL-ES5
XL-ES50
General Information
Accessories
Please confirm that the following accessories are included.
Note:
Only the above accessories are included.
Contents
Page
General Information
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Controls and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 - 9
Preparation for Use
System connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 12
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Basic Operation
General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
CD Playback
Listening to a CD (CDs) . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 - 18
Advanced CD playback . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 - 21
Radio
Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22, 23
Advanced Features
Timer and sleep operation . . . . . . . . . . . . . . . . . . . . . . . . .24 - 26
Enhancing your system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
References
Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28, 29
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
CONSUMER LIMITED WARRANTY . . . . . . . . . . . . . . .Back cover
Remote control 1 FM/AM loop antenna 1
(RRMCGA003SJSA) (QANTL0009SJZZ)
AC power cord 1
(QACCU0003SJ00)

6
XL-ES5
XL-ES50
General Information
Precautions
General
zPlease ensure that the equipment is positioned in a well-venti-
lated area and ensure that there is at least 4" (10 cm) of free
space along the sides, top and back of the equipment.
zDo not place anything on top of the unit.
zDo not expose the unit to moisture, to temperatures higher than
140°F (60°C) or to extremely low temperatures.
zIf your system does not work properly, disconnect the AC power
cord from the AC outlet. Plug the AC power cord back in, and
then turn on your system.
zThis unit should only be used within the range of 41°F - 95°F
(5°C - 35°C).
Warning:
The voltage used must be the same as that specified on this unit.
Using this product with a higher voltage other than that which is
specified is dangerous and may result in a fire or other type of acci-
dent causing damage. SHARP will not be held responsible for any
damage resulting from use of this unit with a voltage other than that
which is specified.
Volume control
The sound level at a given volume setting depends on speaker effi-
ciency, location and various other factors. It is advisable to avoid
exposure to high volume levels, which occurs while turning the unit
on with the volume control setting up high, or while continually lis-
tening at high volumes.
zUse the unit on a firm, level surface free from
vibration.
zKeep the unit away from direct sunlight,
strong magnetic fields, excessive dust,
humidity and electronic/electrical equip-
ment (home computers, facsimiles, etc.)
which generate electrical noise.
zIn case of an electrical storm, unplug the
unit for safety.
4" (10 cm)
4" (10 cm) 4" (10 cm) 4" (10 cm)
zHold the AC power plug by the head when
removing it from the AC outlet, as pulling
the cord can damage internal wires.
zDo not remove the outer cover, as this
may result in electric shock. Refer inter-
nal service to your local SHARP service
facility.

7
XL-ES5
XL-ES50
General Information
Controls and indicators
Front panel Reference page
1.Equalizer Mode Select Button . . . . . . . . . . . . . . . . . . . . . . 14
2.Extra Bass/Demo Mode Button . . . . . . . . . . . . . . . . . . 12, 14
3.Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.Power On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.Video/Auxiliary Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
8.Disc Compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
9.Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
10.Remote Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
11.CD Stop, Tuning Down Button . . . . . . . . . . . . . . . . . . . 18, 22
12.CD Play or Repeat, Tuning Up Button . . . . . . . . . . 17, 20, 22
13. CD Track Down or Fast Reverse,
Tuner Preset Down Button. . . . . . . . . . . . . . . . . . . . . . . 18, 23
14.CD Track Up or Fast Forward,
Tuner Preset Up Button . . . . . . . . . . . . . . . . . . . . . . . . . 18, 23
15.Memory/Set Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21, 23
16.Disc Compartment Open/Close Button . . . . . . . . . . . . . . . 16
17. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 19
18.Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Display Reference page
1.Disc Number Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.CD Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.CD Pause Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4.Memory Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.CD Repeat Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.Extra Bass Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.Sleep Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
8.Timer Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
9.FM Stereo Mode Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 22
10.FM Stereo Receiving Indicator . . . . . . . . . . . . . . . . . . . . . . 22
10
18
11
12
13
14
15
16
17
6 7321 4 5 8
9
10
4
8
9
1
2
3
5
6
7

8
XL-ES5
XL-ES50
General Information
Controls and indicators (continued)
Rear panel Reference page
1.AC Power Input Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.Speaker Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.FM/AM Loop Antenna Jack . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.Video/Auxiliary (Audio Signal) Input Jacks . . . . . . . . . . . . 27
5.Cooling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Front speaker
1.Super Tweeter
2.Woofer
3.Bass Reflex Duct
4.Speaker Wire
Subwoofer
1.Sub Duct Pipe
2.Subwoofer
3.Speaker Wire
Note:
The speaker grilles are not removable.
13
4
5
3
3
4
2
1
2
1
2

9
XL-ES5
XL-ES50
General Information
Remote control Reference page
1.Remote Control Transmitter . . . . . . . . . . . . . . . . . . . . . . . . 13
2.Power On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.Direct Track Search Buttons . . . . . . . . . . . . . . . . . . . . . . . . 19
4.CD Track Down or Fast Reverse,
Tuner Preset Down, Time Down Button . . . . . . . . . 15, 18, 23
5.CD Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.Extra Bass Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.CD Play or Repeat Button . . . . . . . . . . . . . . . . . . . . . . . 17, 20
8.Volume Up and Down Buttons . . . . . . . . . . . . . . . . . . . . . . 14
9.Memory/Set Button . . . . . . . . . . . . . . . . . . . 15, 21, 23, 24, 26
10.CD Clear Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
11.CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
12. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 19
13.CD Track Up or Fast Forward,
Tuner Preset Up, Time Up Button . . . . . . . . . . . . . . 15, 18, 23
14.CD Pause Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
15.Equalizer Mode Select Button . . . . . . . . . . . . . . . . . . . . . . 14
16.CD Random Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
17.Timer/Sleep Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24, 26
18.Video/Auxiliary Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
19.Clock Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
20.Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
1
19
18
20
17
16
15
14
13
12
4
5
6
7
8
9
10
11
2
3

10
XL-ES5
XL-ES50
Preparation for Use
System connections
Front speaker (left)Front speaker (right)Subwoofer
AC outlet
(AC 120V, 60 Hz)
Speaker connection (see page 11)
AM loop antenna
FM antenna
Make sure to unplug the AC power cord before any connections.
FM/AM loop antenna connection (see page 11)
Connecting the AC power cord (see page 12)

11
XL-ES5
XL-ES50
Preparation for Use
FM/AM loop antenna connection
Connect the FM/AM loop antenna to the ANTENNA jack.
Position the FM antenna wire and rotate the AM loop antenna for
optimum reception. Place the AM loop antenna on a shelf, or attach
it to a stand or a wall.
Notes:
zPlacing the antenna on the stereo system or near the AC power
cord may cause noise pickup. Place the antenna away from the
stereo system for better reception.
zDo not connect the attached FM antenna to an external antenna
as this may cause trouble.
Installing the AM loop antenna:
Speaker connection
Connect the black wire to the minus (-) terminal, and the red wire to
the plus (+) terminal.
Caution:
< Assembling > < Attaching to the wall >
Wall Screws (not supplied)
zUse speakers with an impedance of 6 ohms or more, as lower im-
pedance speakers can damage the unit.
zDo not mistake the right and the left chan-
nels.The rightspeaker istheoneon theright
side when you face the unit.
zDo not let the bare speaker wires touch
each other.
zDo not allow any objects to fall into or to be
placed in the bass reflex ducts.
zDo not standor sit on the speakers. You may
be injured. Incorrect
Red Black
Front speaker
(right)
Subwoofer Front speaker
(left)

12
XL-ES5
XL-ES50
Preparation for Use
System connections (continued)
Connecting the AC power cord
After checking all the connections have been made correctly, con-
nect the AC power cord to the AC power input jack, then plug the AC
power cord of this unit into the AC outlet. If you plug in the unit first,
the unit will enter the demonstration mode.
Notes:
zNever use a power cord other than the one supplied. Otherwise,
a malfunction or an accident may occur.
zUnplug the AC power cord from the AC outlet if the unit will not be
in use for a prolonged period of time.
Demonstration mode
Notes:
zThe speakers are magnetically shielded.
Therefore, they do not affect the display even ifyou use them near
the TV. However, some color variation may occur, depending on
the type of TV used.
If color variation occurs...
Turn off the TV (from the power switch).
After 15 - 30 minutes, turn the TV on again.
If the color variation is still present...
Move the speakers further away from the TV.
zIf any kind of magnet or an electromagnet is placed too close to
the TV and the system, irregular colors may appear on the TV
screen.
AC outlet
(AC 120V, 60 Hz)
Cooling fan:
This product is equipped with a cooling fan inside for better heat ra-
diation.
The first time the unit is plugged in, the
unit will enter the demonstration mode.
You will see words scroll.
To cancel the demonstration
mode:
When the unit is in the power stand-
by mode (demonstration mode),
press the X-BASS/DEMO button.
The unit will enter the low power
consumption mode.
To return to the demonstration mode:
When the unit is in the power stand-by mode, press the X-BASS/
DEMO button again.
Note:
When the power is on, the X-BASS/DEMO button can be used to se-
lect the extra bass mode.

13
XL-ES5
XL-ES50
Preparation for Use
Remote control
Battery installation
Precautions for battery use:
zReplace all old batteries with new ones at the same time.
zDo not mix old and new batteries.
zRemove the batteries if the unit will not be used for long periods
of time. This will prevent potential damage due to battery leak-
age.
Caution:
zDo not use rechargeable batteries (nickel-cadmium battery, etc.).
zInstalling the batteries incorrectly may cause the unit to malfunc-
tion.
Notes concerning use:
zReplace the batteries if the operating distance is reduced or if the
operation becomes erratic.
zPeriodically clean the transmitter on the remote control and the
sensor on the unit with a soft cloth.
zExposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit if this
occurs.
zKeep the remote control away from moisture, heat, shock, and
vibrations.
Test of the remote control
Check the remote control after checking all the connections (see
pages 10 - 12).
Point the remote control directly at the remote sensor on the unit.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now, you
can enjoy music.
Use 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar).
Batteries are not included.
1 Remove the battery cover.
2 Insert the batteries according to the direction indicated in
the battery compartment.
When inserting or removing the batteries, push them toward the
battery terminals.
3 Replace the cover.
8" - 20'
(0.2 m - 6 m)
Remote sensor

14
XL-ES5
XL-ES50
Basic Operation
General control
To turn the power on
Press the ON/STAND-BY button to turn the power on.
Volume control
Main unit operation:
When the VOLUME control is turned clockwise, the volume will
increase. When it is turned counterclockwise, the volume will
decrease.
Remote control operation:
Press the VOLUME (+ or -) button to increase or decrease the vol-
ume.
Bass control (X-BASS)
When the power is first turned on, the unit will enter the extra bass
mode which emphasizes the bass frequencies, and "X-BASS" will
appear. To cancel the extra bass mode, press the X-BASS/DEMO
(X-BASS) button.
Equalizer
When the EQUALIZER (EQUALIZER MODE) button is pressed, the
current mode setting will be displayed. To change to a different
mode, press the EQUALIZER (EQUALIZER MODE) button repeat-
edly until the desired sound mode appears.
After use:
Press the ON/STAND-BY button to enter the power stand-by
mode.
30 MAXIMUM0 .....
ROCK
FLAT
CLASSIC
The sound is not modified.
Bass and treble are emphasized.
POPS
Bass and treble are slightly emphasized.
JAZZ
Treble is slightly emphasized.
Treble is cut a little.
VOCAL
Vocals (midrange tones) are emphasized.

15
XL-ES5
XL-ES50
Basic Operation
Setting the clock
In this example, the clock is set for the 12-hour (AM 12:00) display.
To confirm the time display:
Note:
The "CLOCK" or time will flash at the push of the CLOCK button
when the AC power supply is restored after a power failure or
unplugging the unit.
Readjust the clock as follows.
To readjust the clock:
Perform "Setting the clock" from step 1. If the "CLOCK" is not flash-
ing in step 1, step 2 (for selecting the 12-hour or 24-hour display) will
be skipped.
To change the 12-hour or 24-hour display:
1Press the CLOCK button and within 8 seconds, press the
MEMORY/SET button.
2Within 30 seconds, press the PRESET ( or ) button to
select 12-hour or 24-hour display and then press the MEM-
ORY/SET button.
"AM 12:00" The 12-hour display will appear.
(AM 12:00 - PM 11:59)
"0:00" The 24-hour display will appear.
(0:00 - 23:59)
3Within 30 seconds, press the PRESET ( or ) button to
adjust the hour and then press the MEMORY/SET button.
Press the PRESET ( or ) button once to advance the time
by 1 hour. Hold it down to advance continuously.
4Within 30 seconds, press the PRESET ( or ) button to
adjust the minutes and then press the MEMORY/SET but-
ton.
Press the PRESET ( or ) button once to advance the time
by 1 minute. Hold it down to advance continuously.
Press the CLOCK button.
The time display will appear for
about 8 seconds.
1 Clear all the programmed contents. [Refer to "Clearing all the
memory (reset)" on page 29 for details.]
2 Perform "Setting the clock" from step 1.

16
XL-ES5
XL-ES50
CD Playback
Listening to a CD (CDs)
This system can also play audio CD, CD-R and CD-RW discs, but
cannot record.
Some audio CD-R and CD-RW discs may not be playable due to the
state of the disc or the equipment used for recording.
CD playback
1Press the ON/STAND-BY button to turn the power on.
2Press the CD button.
3Press the OPEN/CLOSE button
to open the disc compartment.
All trays open in tiers.
4Place the CD on the disc tray 1, label side up.
Be sure to place 3" (8 cm) CD in the middle of the disc trays.
5To place discs in the trays 2 - 5
1. Slide in the tray with a disc to-
ward the unit.
2. Place a disc in an empty tray.
5" (12 cm) 3" (8 cm)

17
XL-ES5
XL-ES50
CD Playback
zPlayback will begin from track 1 on disc 1. After that disc finishes
playing, the next disc will automatically play.
zAfter the last track on the fifth disc is played, the CD player stops
automatically.
zWhen there is no CD in one of the disc trays (1 - 5), the empty
tray will be skipped to the next tray with a CD.
To exchange other CDs while playing a disc:
Press the OPEN/CLOSE button. When trays open, exchange discs.
The tray in use does not open.
To remove the CDs:
To specify a tray to open:
6Press the OPEN/CLOSE button to close the disc compart-
ment.
Total number of tracks on the CD
whose number is flashing Total playing time of the CD whose number is
flashing
7Press the / button to start playback.
CD play indicator
1. In the stop mode, press the
OPEN/CLOSE button.
zAll trays open in tiers.
2. Remove the disc in the tray 1.
3. Slide in the tray 1 toward the unit.
In the same way, remove discs in
the trays 2 - 5.
4. After removing the discs, press
the OPEN/CLOSE button again.
1. In the stop mode, press the 1 - 5 button.
2. Press the OPEN/CLOSE button.
3. Remove the disc, then press the OPEN/CLOSE button again.

18
XL-ES5
XL-ES50
CD Playback
Listening to a CD (CDs) (continued)
Various CD functions Notes:
Caution:
zDo not place two CDs in one disc tray.
zDo not play discs with special shapes (heart- or octagon-shaped)
as it may cause malfunctions.
zDo not push the disc compartment while it is moving.
zIf the power fails while the disc compartment is open, wait until
the power is restored.
zIf the disc compartment is stopped with force, the unit will not
function. If this occurs, press the ON/STAND-BY button to enter
the power stand-by mode and then turn the power on again.
zIf TV or radio interference occurs during CD operation, move the
unit away from the TV or radio.
zIf a disc is damaged, dirty, or loaded upside down, the disc will
skip or not play.
Function Main unit Remote
control Operation
Play Press in the stop mode.
Stop Press in the playback
mode.
Pause Press in the playback
mode. Press the / but-
ton to resume playback
from the paused point.
Track up/
Track down Press in the playback or stop mode.
Ifyoupressthebuttoninthe
stop mode, press the /
button to start the desired
track.
Fast for-
ward/Fast
reverse
Press and hold down in the
playback mode.
Release the button to re-
sume playback.
zTrack up/track down and fast forward/fast reverse are possible
only within one disc.
zWhen the end of the last track is reached during fast forward, "
END" will appear on the display and CD operation will bepaused.
When the beginning of the first track is reached during fast re-
verse, the unit will enter the playback mode.
( : Last track number)

19
XL-ES5
XL-ES50
CD Playback
Advanced CD playback
To play from a specified disc
You can start playback from the desired disc by selecting the num-
ber.
zPlayback will begin from track 1 on the chosen disc. After that
disc finished playing the next disc automatically play.
zAfter the last track on the fifth disc is played, the CD player stops
automatically.
Note:
If a disc tray with no disc is selected, playback will not start and the
disc indicator will go out.
To stop playback:
Press the button.
Direct track search
By using the direct search buttons, the desired tracks on the current
disc can be played.
If the direct search buttons are pressed while the disc is stopped,
press the / button to start the desired track on the current disc.
Notes:
zA track number higher than the number of tracks on the disc can-
not be selected.
zDuring random play, direct search is not possible.
1Press one of the 1 - 5 buttons to select the desired disc.
Selected disc number
2Press the / button.
Use the direct search buttons on
the remote control to select the de-
sired track while playing the se-
lected disc.
Selected track number
zThe direct search buttons allow you to select up to number 9.
zWhen selecting number 10 or higher, use the +10 button.
A. For example, to choose 13
1 Press the "+10" button once.
2 Press the "3" button.
B. For example, to choose 30
1 Press the "+10" button three times.
2 Press the "0" button.

20
XL-ES5
XL-ES50
CD Playback
Advanced CD playback (continued)
Repeat play
You can play up to 5 discs, or a programmed tracks continuously.
To cancel repeat play:
Press the / button again.
" " will go out.
Caution:
After performing repeat play, be sure to press the button. Other-
wise, the disc(s) will play continuously.
Random play
The tracks on the disc(s) can be played in random order automati-
cally.
To cancel random play:
Press the button.
"R" will go out.
Notes:
zRandom play will stop automatically when all tracks are played
once. (The same track will not be played back twice.)
zIf you press the button during random play, you can move to
the next track by the random operation. On the other hand, the
button does not allow you to move to the previous track. The
beginning of the track being played will be located.
zIn random play, the CD player will select and play tracks automat-
ically. (You cannot select the order of the tracks.)
To repeat all tracks on up to 5 discs:
Press the / button twice.
To repeat desired tracks:
Perform steps 1 - 4 in the "Programmed play" section on page 21
and then press the / button twice.
To repeat random play:
Press the / button during random play.
To random play all tracks on up to 5 discs:
Press the RANDOM button on the remote control.