Sharp EC-SC75H-H User manual

EC-SC75H-H
Read this operation manual carefully before first
use. Keep this manual for further guidance in case.
Operation
Manual
Cordless Vacuum Cleaner

Personal Safety:
Contents
……………………………………………………………………............... EN-1
Introduction of Product Components
…………………………………………………… EN-3
Operation Method
…………………………………………………………………………………….…… EN-4
Troubleshooting ……………………………………………………………………………………………… EN-7
Safety Operation Guide
Safety Operation Guide
EN-1
Specifications…………………………………………………………………………………………...........…EN-7

Aluminium
Tube
Charger Long Crevice Nozzle
Bristle Brush Nozzle
Hanger
EN-2 EN-3
Introduction of Product Components
Safety Operation Guide
Power Rolling Nozzle
Dust Cup
On/Off Button
Handle Latch
Aluminium
Tube Latch
Head Latch

4.Press the On/Off button to start the machine.
Two suction speeds control.
II. How to use as a handheld vacuum:
Insert the accessory(bristle brush or long crevice ) to the main part as
shown below until hearing the click sound
I.Use as the stick vacuum cleaner:
1.Assemble the battery into the dust cup, make sure the battery bolt head is inserted
into the dust cup slot rightly as below.
2.Attach the aluminium tube to the main part as below until hearing the click sound.
3.Attach the head to the tube as shown below.
Operation Method Operation Method
Battery Bolt head
On/Off button
Dust Cup Slot
III. How to charge:
Note： Hanger installation method
1. Use expansion screws to hang the vacuum cleaner on the wall.
Blinking
Charging port
Wall
EN-5EN-4
a. Turn on the On/Off button to the low speed mode.
b.
c. Press the On/Off button again to stop the machine.
Press the On/Off button again to change to
high speed mode.
1) When only one indicator light is blinking, please turn off the appliance. Hang up the
machine and then plug in charger power cable into the main body for charging.
When charging, the indicate lights will become flashing green.

2) It will have 3 green lights on after fully charged.
IV. Dust cup cleaning method:
Operation Method Troubleshooting/Specifications
1）Press the handle locker to
remove the battery from dust cup.
3）Take out the filter case, then
take out the filter.
5）Please dry the filter and the filter
case completely before assembling
back.
7）Put the filter case back to the
dust cup.
※Troubleshooting:
※Specifications
8）Assemble the top cover to the
dust cup.
6）After drying, assemble the filter
to the case.
）4
by water.
Wash the filter case and the filter
2）Separate and remove the top cover
as shown below.
Suction gets weak
1. Empty the dust cup
2. Check if the dust cup is installed correctly
3.
correctly
4. Clean the filter
Stop working 1. Charge the vacuum
2. Clean the rolling brush and the bearing thoroughly
Battery doesn t hold
a charger
1. Check if the plug has been inserted already
2. Check if the socket is useful
4-5
hours
Power supply Input 100-240V~50-60Hz (Charger)
Power supply method Rechargeable type ( lithium ion battery,22.2V )
Electric power consumption While charging : Approx. 11.7W;
After charging : Approx. 0W
Low: Approx. 40 mins
High: Approx. 20 mins
Dust collecting capacity 0.55L
Charging time 4-5 hrs
Weight(Charger) 88g
Base unit dimensions 240mm W × 1050mm H × 210mm D
Charger dimensions 51mm W × 36mm H ×77mm D
Cord length（Charger） 180cm
2.4kg
Weight(Suction head,pipe,
base unit and battery included)
EN-7EN-6
Continuous operation time
Check if the filter case and the filter are installed

SHARP CORPORATION