Shop fox W1742W User manual

OWNER'S MANUAL
(FOR MODELS MANUFACTURED SINCE 9/15)
MODEL W1742W, W1742SW,
W1754W, W1754SW
15" & 20" PLANERS
Phone: [phone] • Online Technical Support: [email protected]
COPYRIGHT © JANUARY, 2016 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#17486WK Printed in China

This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre-
hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property
damage from negligence, improper training, machine modifications or
misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement and other masonry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip-
ment, such as those dust masks that are specially designed to filter
out microscopic particles.

SET UPELECTRICAL MAINTENANCE SERVICE PARTS
OPERATIONS
SAFETYINTRODUCTION
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
INTRODUCTION .....................................2
Contact Info....................................... 2
Machine Differences ............................. 2
Manual Accuracy.................................. 2
Machine Specifications .......................... 3
Identification ..................................... 5
Controls & Components ......................... 6
Internal Components ............................ 7
SAFETY ...............................................8
Standard Machinery Safety Instructions ...... 8
Additional Safety for Planers................. 10
ELECTRICAL ....................................... 11
Circuit Requirements .......................... 11
Grounding Requirements...................... 12
Extension Cords ................................ 12
SETUP .............................................. 13
Unpacking ....................................... 13
Items Needed for Setup....................... 13
Inventory ........................................ 14
Cleaning Machine............................... 15
Machine Placement ............................ 16
Lifting & Moving ................................ 17
Assembly......................................... 18
Dust Collection ................................. 19
Checking Gearbox Oil Level .................. 20
Test Run.......................................... 21
OPERATIONS....................................... 22
General .......................................... 22
Workpiece Inspection.......................... 23
Wood Types...................................... 23
Planing Tips ..................................... 24
Cutting Problems ............................... 24
Depth of Cut .................................... 26
Bed Roller Height .............................. 27
Setting Feed Rate .............................. 28
Adjusting/Replacing Knives
(W1742W & W1754W) ......................... 28
Adjusting/Replacing Knives................... 28
Rotating/Replacing Cutterhead Inserts
(W1742SW & W1754SW)....................... 30
ACCESSORIES ...................................... 31
Planer Accessories ............................. 31
MAINTENANCE .................................... 32
Schedule ......................................... 32
Cleaning & Protecting ......................... 32
Lubrication ...................................... 32
SERVICE ............................................ 35
General .......................................... 35
Tensioning/Replacing V-Belts................. 35
Tensioning Table Height Chain ............... 36
Feed Rollers, Chip Breaker &
Pressure Bar Heights........................... 37
Adjusting Roller Spring Tension .............. 41
Positioning Chip Deflector .................... 42
Calibrating Table Height Scale ............... 43
Anti-Kickback Fingers.......................... 43
Pulley Alignment ............................... 44
Troubleshooting................................. 45
Electrical Safety Instructions................. 47
W1742W & W1742SW Wiring Diagram....... 48
W1754W & W1754SW Wiring Diagram....... 49
PARTS: W1742W & W1742SW ................. 50
Headstock ....................................... 50
Table ............................................. 52
Base .............................................. 53
Gearbox.......................................... 54
Feed Gearing.................................... 55
Cabinet Stand................................... 56
PARTS: W1754W & W1754SW ................. 58
Headstock ....................................... 58
Table ............................................. 60
Base .............................................. 61
Gearbox.......................................... 62
Feed Gearing.................................... 63
Cabinet Stand................................... 64
PARTS: LABELS & COSMETICS.................. 66
WARRANTY ........................................ 69
Contents

-2-
W1742W, W1742SW, W1754W, W1754SW (Mfd. Since 9/15)
INTRODUCTION
INTRODUCTION
We are proud to provide a high-quality owner’s
manual with your new machine!
We
made every effort to be exact with
the
instructions, specifications, drawings, and pho-
tographs contained inside. Sometimes we make
mistakes, but our policy of continuous improve-
ment
also means that sometimes the
machine
you receive will be slightly different than what
is shown in the manual
.
If you find this to be the case, and the difference
between the manual and machine leaves you
confused about a procedure
,
check our website
for an updated version. W
e post current
manuals
and
manual updates for free
on our website at
www.
woodstockint.com.
Alternatively, you can call our Technical Support
for help. Before calling, make sure you write
down the
Manufacture Date and Serial Number
from the machine ID label (see below). Also, if
available, have a copy of your original purchase
receipt on hand. This information is required for
all Tech Support calls.
MODEL XXXX
MACHINE NAME
Motor:
Specification:
Specification:
Specification:
Specification:
Weight:
Specifications
To reduce risk of serious personal injury when using this
machine:
1. Read & understand owner’s manual before operating.
2. Always wear approved eye protection and respirator.
3. Only plug power cord into a grounded outlet.
4. Only use this machine to collect wood dust/chips—never
use to collect glass, metal, liquids, asbestos, silica,
animal parts, biohazards, burning material/ashes, etc.
5. Always disconnect power before servicing or cleaning.
6. Do not expose to rain or wet areas.
7. Keep hands, long hair, and loose clothing away from
inlet.
8. Never leave machine unattended while it is running.
9. Do not use if cord/plug becomes damaged—promptly
repair and protect cord from future damage.
10. Do not use without dust bag or filters in place.
11. Always wear a respirator when emptying bags.
12. Prevent unauthorized use by children or untrained users.
Date
Serial Number
Manufactured for Woodstock in Taiwan
WARNING!
Manufacture
Date
Serial Number
Manual Accuracy
We are committed to customer satisfaction. If
you have any questions or need help, use the
information below to contact us.
IMPORTANT: Before contacting, please get the
original purchase receipt, serial number, and
manufacture date of your machine. This infor-
mation is required for all Technical Support
calls and it will help us help you faster.
Woodstock International Technical Support
Phone: [phone]
Email: [email protected]
We want your feedback on this manual. What did
you like about it? Where could it be improved?
Please take a few minutes to give us feedback.
Technical Documentation Manager
P.O. Box 2309
Bellingham, WA 98227
Email: [email protected]
Contact Info
• Models W1742W and W1742SW are 3 HP, 15"
planers.
— Model W1742W has a 3-knife cutterhead.
— Model W1742SW has a spiral cutterhead.
• Models W1754W and W1754SW are 5 HP, 20"
planers.
— Model W1754W has a 4-knife cutterhead.
— Model W1754SW has a spiral cutterhead.
Machine Differences

-3-
W1742W, W1742SW, W1754W, W1754SW (Mfd. Since 9/15)
INTRODUCTION
Model Number W1742W W1742SW W1754W W1754SW
Product Dimensions
Weight 532 lbs. 534 lbs 781 lbs. 790 lbs.
Width (side-to-side) x Depth
(front-to-back) x Height 38" x 42" x 44" 38" x 42" x 44" 44" x 56
1⁄2" x 45" 44" x 56 1⁄2" x 45"
Foot Print (Length x Width) 19" x 231⁄2"23" x 29"
Shipping Dimensions
Type Wood Crate
Weight 614 lbs. 625 lbs. 878 lbs. 891 lbs.
Width (side-to-side) x Depth
(front-to-back) x Height 37" x 25" x 48" 37" x 25" x 48" 43" x 30" x 48" 43" x 30" x 48"
Electrical
Power Requirement 240V, Single-Phase, 60 Hz
Full-Load Current Rating 15A 20A
Minimum Circuit Size 20A 30A
Connection Type Cord & Plug
Power Cord Included Yes
Power Cord Length 7 ft. 7 ft.
Power Cord Gauge 12 AWG
Plug Included Yes
Included Plug Type 6-20 L6-30
Switch Type Magnetic Switch w/Overload Protection
Motor
Type TEFC Capacitor-Start Induction
Horsepower 3 HP 5 HP
Phase Single-Phase
Amps 15A 20A
Speed 3450 RPM
Power Transfer Belt Drive
Bearings Sealed & Permanently Lubricated
Manufacturer Specifications
Country of Origin China
Warranty 1 Year
Approx. Assembly & Setup
Time 1 Hour
Serial Number Location ID Label
ISO 9001 Factory Yes
Certified by NRTL No
© Woodstock International, Inc. • Phone #: [phone] • Web: www.shopfox.biz
MACHINE
SPECIFICATIONS

-4-
W1742W, W1742SW, W1754W, W1754SW (Mfd. Since 9/15)
INTRODUCTION
Model Number W1742W W1742SW W1754W W1754SW
Main Specifications
Planer Size 15 in. 20 in.
Max. Cut Width 15 in. 20 in.
Max. Stock Thickness 8 in.
Min. Stock Thickness 3⁄16 in.
Min. Stock Length 61⁄2in. 71⁄2in.
Number of Cuts Per Inch 104, 56 104, 83
Number of Cuts Per Minute 15,000 20,000
Cutterhead Speed 5000 RPM
Planing Feed Rate 16, 20 FPM
Max. Cut Depth Planing Full
Width
1⁄8in.
Max. Cut Depth Planing
6-Inch Wide Board
5⁄32 in. 1⁄4in.
Cutterhead Info
Cutterhead Type 3-Knife Spiral 4-Knife Spiral
Cutterhead Diameter 27⁄8in. 31⁄16 in.
Number of Knives 3N/A 4N/A
Knife Type HSS, Single-
Sided, Solid N/A HSS, Single- Sided, Solid N/A
Knife Length 15 in. N/A 20 in. N/A
Knife Width 1 in. N/A 1 in. N/A
Knife Thickness 1⁄8in. N/A 1⁄8in. N/A
Knife Adjustment Jack Screws N/A Jack Screws N/A
Number of Spirals N/A 4N/A 4
Number of Indexable Cutters N/A 72 N/A 96
Cutter Insert Type N/A Indexable
Carbide N/A Indexable Carbide
Cutter Insert Length N/A 14 mm N/A 14 mm
Cutter Insert Width N/A 14 mm N/A 14 mm
Cutter Insert Thickness N/A 2 mm N/A 2 mm
Table Info
Table Movement 8 in.
Table Bed Length x Width 413⁄4x 16 in. 561⁄2x 21 in.
Table Bed Thickness 23⁄8in.
Flo or-to-Table Height 25–323⁄4 in. 253⁄8–333⁄4in.
Construction
Table Precision-Ground Cast Iron
Body Cast Iron
Stand/Cutterhead Assembly Steel
Feed Rollers Infeed: Serrated Steel/Outfeed: Rubber
Paint Type/Finish Powder Coated

-5-
W1742W, W1742SW, W1754W, W1754SW (Mfd. Since 9/15)
INTRODUCTION
Identification
Become familiar with the names and locations of the controls and features shown below to better
understand the instructions in this manual.
To reduce your risk of serious injury
or damage to the machine, read this
entire manual BEFORE using machine.
Feed Rate
Control Knob
Table
Locks
Bed Rollers
Lifting
Bars
(2 of 4)
Front
Extension
Wing
Mobile-Base
Foot Pedal
Cabinet
Access
Panel
Control Panel Return Rollers
Table
Height
Handwheel
Gearbox
Table
Height
Scale

-6-
W1742W, W1742SW, W1754W, W1754SW (Mfd. Since 9/15)
INTRODUCTION
Controls & Components
Refer to the Figures 1–3 and the following descriptions to
become familiar with the basic controls and components
of this machine. Understanding these items and how they
work will help you understand the rest of the manual and
stay safe when operating this machine.
A. Control Panel for Magnetic Switch: Green START
button turns motor ON when pressed. Red Emergency
STOP button turns motor OFF when pressed; for
safety purposes, this button will remain depressed
and prevent restarting until reset. Reset by rotating
clockwise until it pops out.
B. Table Height Handwheel: Raises and lowers table
to accommodate different workpiece thicknesses.
One complete revolution moves the table
approximately 1⁄16".
C. Feed Rate Control Knob: Selects 20 FPM feed rate
when pushed in, and 16 FPM feed rate when pulled
out.
D. Table Locks: Secure table height position when
tightened.
E. Depth-of-Cut Limiter: Limits depth of cut to a
maximum of 1⁄8" at full width.
F. Return Rollers: Assist sliding workpiece back to
operator following planing operation.
G. Dust Port: Connects to a dust collection system to
extract shavings and dust during operation.
To reduce your risk of serious injury
or damage to the machine, read this
entire manual BEFORE using machine.
Figure 1. Table elevation and feed
controls.
AB
C
D
Figure 2. Return rollers and dust port.
G
F
Figure 3. Mobile-base foot pedal.
H
H. Mobile-Base Foot Pedal: When engaged, lifts
machine onto casters for repositioning. When
disengaged, allows machine to rest firmly on floor
during operations.
E

-7-
W1742W, W1742SW, W1754W, W1754SW (Mfd. Since 9/15)
INTRODUCTION
Internal Components
F. Pressure Bar (W1754W & W1754SW):
Stabilizes the workpiece as it leaves the
cutterhead and assists in deflecting wood
particles toward the dust port.
G. Outfeed Roller: Pulls the workpiece
through the planer.
H. Table Rollers: Provide upward pressure on
the workpiece,enabling the feed rollers to
pull the workpiece along.
I. Planer Table: Provides a smooth and level
path for the workpiece as it moves through
the planer.
A. Anti-Kickback Fingers: Provide additional
safety for the operator.
B. Serrated Infeed Roller: Pulls the workpiece
toward the cutterhead.
C. Chip Breaker: Breaks off chips created by
the cutterhead to prevent tear out and
diverts the chips to the dust port.
D. Chip Deflector: Directs chips into the dust
hood.
E. Cutterhead: Holds the knives/indexable
carbide inserts that remove material from
the workpiece.
Like all machinery there is potential danger when operating this machine. Accidents are fre-
quently caused by lack of familiarity or failure to pay attention. Use this machine with respect
and caution to decrease the risk of operator injury. If normal safety precautions are overlooked
or ignored, serious personal injury may occur.
Workpiece
Figure 4. Workpiece path and major planing components (side cutaway view).
A
C
B
E
H H
I
F
G
D
FRONT REAR

-8-
SAFETY
W1742W, W1742SW, W1754W, W1754SW (Mfd. Since 9/15)
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
This symbol is used to alert the user to useful information about
proper operation of the equipment or a situation that may cause
damage to the machinery.
NOTICE
SAFETY
OWNER’S MANUAL.
Read and understand this
owner’s manual BEFORE using machine.
TRAINED OPERATORS ONLY.
Untrained operators
have a higher risk of being hurt or killed. Only
allow trained/supervised people to use this
machine. When machine is not being used,
disconnect power, remove switch keys, or
lock-out machine to prevent unauthorized
use—especially around children. Make
workshop kid proof!
DANGEROUS ENVIRONMENTS.
Do not use
machinery in areas that are wet, cluttered,
or have poor lighting. Operating machinery
in these areas greatly increases the risk of
accidents and injury.
MENTAL ALERTNESS REQUIRED.
Full mental
alertness is required for safe operation of
machinery. Never operate under the influence
of drugs or alcohol, when tired, or when
distracted.
ELECTRICAL EQUIPMENT INJURY RISKS. You can
be shocked, burned, or killed by touching live
electrical components or improperly grounded
machinery. To reduce this risk, only allow an
electrician or qualified service personnel to
do electrical installation or repair work, and
always disconnect power before accessing or
exposing electrical equipment.
DISCONNECT POWER FIRST. Always disconnect
machine from power supply BEFORE making
adjustments, changing tooling, or servicing
machine. This eliminates the risk of injury
from unintended startup or contact with live
electrical components.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating
or observing machinery to reduce the risk of
eye injury or blindness from flying particles.
Everyday eyeglasses are not approved safety
glasses.
Standard Machinery Safety Instructions
For Your Own Safety,
Read Manual Before Operating Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This
manual uses a series of symbols and signal words intended to convey the level of importance of the
safety messages. The progression of symbols is described below. Remember that safety messages by
themselves do not eliminate danger and are not a substitute for proper accident prevention mea-
sures—this responsibility is ultimately up to the operator!
SAFETY
Standard Machinery Safety Instructions