Shop fox M1111 User manual

OWNER'S MANUAL
MODEL M1111
MILLING MACHINE
W/DOVETAIL COLUMN
Phone: [phone] • Online Technical Support: [email protected]
COPYRIGHT © MAY, 2007 BY WOODSTOCK INTERNATIONAL, INC. REVISED DECEMBER 2007.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. Printed in China
#9074CR



















 
 
 






SET UPELECTRICAL MAINTENANCE SERVICE PARTS
OPERATIONSSAFETYINTRODUCTION
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
INTRODUCTION ...................................... 2
Woodstock Technical Support .................. 2
Machine Specifications .......................... 3
Identification ..................................... 5
SAFETY ................................................ 6
Safety Instructions for Machinery ............. 6
Additional Safety for Milling Machines ........ 8
ELECTRICAL .......................................... 9
110V Operation ................................... 9
Extension Cords .................................. 9
Electrical Specifications ........................ 9
SETUP ................................................10
Unpacking ........................................10
Inventory .........................................10
Machine Placement .............................11
Cleaning Machine ................................11
Bench Mounting .................................12
Test Run and Spindle Break-In ................13
OPERATIONS ........................................14
General ...........................................14
Spindle Height Control .........................15
Table Travel .....................................15
Headstock Travel ................................16
Drill Chuck .......................................17
R-8 Collets ........................................18
Control Panel ....................................19
Calculating Spindle RPM .......................20
Milling/Drilling Mode ...........................21
Tapping Mode ....................................21
Accessories .......................................22
MAINTENANCE ......................................24
Schedule ..........................................24
Lubrication .......................................24
SERVICE ..............................................25
Troubleshooting .................................25
Troubleshooting .................................26
Gibs and Backlash ...............................27
Service Lubrication .............................29
Electrical Components .........................30
Wiring Diagram .................................32
PARTS ................................................33
Column, Table, and Inverter ..................33
Headstock and Controls ........................35
Label Placement ................................38
Contents

-2-
M1111 Mill with Dovetail Column
INTRODUCTION
Woodstock Technical Support
Your new SHOP FOX® Mill with Dovetail Column has been specially designed to provide many years of
trouble-free service. Close attention to detail, ruggedly built parts and a rigid quality control program
assure safe and reliable operation.
Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to
include the basic information for safety, setup, operation, maintenance, and service of this product.
We stand behind our machines! In the event that questions arise about your machine, please contact
Woodstock International Technical Support at [phone] or send e-mail to: tech-support@shopfox.
biz. Our knowledgeable staff will help you troubleshoot problems and process warranty claims.
INTRODUCTION
If you need the latest edition of this manual, you can download it from http://www.shopfox.biz.
If you have comments about this manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation Manager
P.O. Box 2309
Bellingham, WA 98227
Email: [e-mail]

-3-
M1111 Mill with Dovetail Column
INTRODUCTION
Machine
Specifications
Motor:
Type .............................................................220V Brushless DC Motor (BLDC)
Horsepower ....................................................................................... 1HP
Amps ...........................................................................................12 Amp
Phase ............................................................................................Single
Speed ....................................................................................... 3500 RPM
Cycle .............................................................................................60 Hz
Power Transfer ........................................................................ Cogged Belt
Bearings ......................................................... Sealed, Permanently Lubricated
Product Dimensions:
Weight ........................................................................................ 364 lbs.
Length/Width/Height ..................................................... 27"L x 30"W x 333⁄4"H
Foot Print (Length/Width ................................................................ 16" x 13"
Shipping Dimensions:
Type ..................................................................................... Wood Crate
Content .......................................................................................Machine
Weight ........................................................................................ 437 lbs.
Length/Width/Height .........................................................33"L x 32"W x 42"H
Electrical:
Switch ............................................................................ Forward/Reverse
Switch Voltage .................................................................................. 110V
Cord Length ..................................................................................... 7 ft.
Cord Gauge ................................................................................. 14 gauge
Recommended Circuit Size .................................................................15 Amp
Plug ........................................................................................ NEMA 5-15
Power Supply ....................................................................110V, Single-Phase
Power Inverter ........................................................................ 110V to 220V
Phone #: [phone] • Online Tech Support: [e-mail] • Web: www.shopfox.biz
MACHINE
SPECIFICATIONS
MODEL M1111
MILLING MACHINE WITH DOVETAIL COLUMN
Continued on next page

-4-
M1111 Mill with Dovetail Column
INTRODUCTION
General:
Spindle Travel ................................................................................... 23⁄4"
Drawbar ................................................................................ 7⁄16" x 20 TPI
Spindle Taper .......................................................................................R8
Swing ............................................................................................... 18"
Longitudinal Table Travel .....................................................................157⁄8"
Cross Table Travel .............................................................................. 53⁄4"
Head Travel .....................................................................................147⁄8"
Max. Distance Spindle To Column ............................................................... 8"
Max. Distance Spindle To Table ..............................................................143⁄4"
Max. Drilling Capacity ............................................................................. 1"
Max. Tapping Capacity .......................................................................... 1⁄2"
Max. End Mill Capacity ............................................................................ 1"
Max. Face Mill Capacity ........................................................................... 2"
Spindle Speed Range ..................................................... 100-1750 RPM, +/- 10%
Quill Diameter ................................................................................. 2.362"
Table:
Table Length ...................................................................................215⁄8"
Table Width ...................................................................................... 61⁄4"
Table Thickness ................................................................................. 11⁄2"
No. of T-Slots ........................................................................................ 3
T-Slot Width ................................................................................... 0.470"
T-Slot Height ................................................................................... 0.750"
T-Slot Centers ................................................................................. 111⁄16"
Stud Size .......................................................................................... 3⁄8"
Lead Screw Diameter ........................................................................... 5⁄8"
Lead Screw TPI ..................................................................................... 12
Lead Screw Length ............................................................................... 26"
Construction:
Spindle Housing Construction ............................................................Cast Iron
Table Construction .................................................... Surface Ground Cast Iron
Head Construction .........................................................................Cast Iron
Column Construction .................................................. Surface Ground Cast Iron
Base Construction .........................................................................Cast Iron
Paint ............................................................................................ Epoxy
Features:
3-16mm Drill Chuck with Key R-8/JT-6 Arbor
Leveling Feet
Digital RPM Readout
Digital Milling Depth Readout
Digital Tapping Controls and RPM Adjustment
Tapping Direction Quick-Shift Buttons on Quill Levers
Manual Micro Depth Adjustment
Dovetailed Table Ways
Dovetailed Column Ways

-5-
M1111 Mill with Dovetail Column
INTRODUCTION
Identification
Figure 1. M1111 Identification.
A. Safety Cap and Drawbar
B. Fine Feed Knob
C. Headstock Tilt Scale
D. Main Power Switch
E. Fine Feed Lock Knob w/Assist Lever
F. HHeadstock Lock Lever
G. Precision Dovetailed Column
H. Longitudinal (X-Axis) Handwheel
I. Cast-Iron Base
J. Vertical (Z-Axis) Handwheel
K. Cross (Y-Axis) Handwheel
L. Adjustable Foot
M. Table Locks
N. Longitudinal Scale
O. Milling Table
P. Quill Handle Tapping Button
Q. Drill Chuck
R. Spindle Lock Lever
S. Chip Guard
T. Digital Spindle Depth Unit and Readout
U. Chip Guard Safety Kill Switch
V. Emergency Stop Button
W. Control Panel
X. Digital Spindle RPM Readout
X
I
J
G
F
D
C
E
A
R
S
P
O
N
L
W
V
U
K
T
Q
B
H
M

-6-
M1111 Mill with Dovetail Column
SAFETY
1. READ THROUGH THE ENTIRE MANUAL BEFORE STARTING MACHINERY. Machinery presents seri-
ous injury hazards to untrained users.
2. ALWAYS USE ANSI APPROVED SAFETY GOGGLES WHEN OPERATING MACHINERY. Everyday eye-
glasses only have impact resistant lenses, they are NOT safety goggles.
3. ALWAYS WEAR AN ANSI APPROVED RESPIRATOR WHEN OPERATING MACHINERY THAT PRODUCES
DUST. Wood dust is a carcinogen and can cause cancer and severe respiratory illnesses.
4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause
permanent hearing damage.
5. WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, or jewelry which
may get caught in moving parts. Wear protective hair covering to contain long hair and wear non-
slip footwear.
6. NEVER OPERATE MACHINERY WHEN TIRED, OR UNDER THE INFLUENCE OF DRUGS OR ALCOHOL.
Be mentally alert at all times when running machinery.
For Your Own Safety, Read Instruction Manual
Before Operating this Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This
manual uses a series of symbols and signal words which are intended to convey the level of impor-
tance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper accident
prevention measures.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
This symbol is used to alert the user to useful information about
proper operation of the machine.
NOTICE
Safety Instructions for Machinery
SAFETY

-7-
M1111 Mill with Dovetail Column
SAFETY
7. ONLY ALLOW TRAINED AND PROPERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY.
Make sure operation instructions are safe and clearly understood.
8. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe distance from the
work area.
9. MAKE WORKSHOP CHILD PROOF. Use padlocks, master switches, and remove start switch keys.
10. NEVER LEAVE WHEN MACHINE IS RUNNING. Turn power off and allow all moving parts to come
to a complete stop before leaving machine unattended.
11. DO NOT USE IN DANGEROUS ENVIRONMENTS. DO NOT use machinery in damp, wet locations, or
where any flammable or noxious fumes may exist.
12. KEEP WORK AREA CLEAN AND WELL LIT. Clutter and dark shadows may cause accidents.
13. USE A GROUNDED EXTENSION CORD RATED FOR THE MACHINE AMPERAGE. Undersized cords
overheat and lose power. Replace extension cords if they become damaged. DO NOT use exten-
sion cords for 220V machinery.
14. ALWAYS DISCONNECT FROM POWER SOURCE BEFORE SERVICING MACHINERY. Make sure switch is
in OFF position before reconnecting.
15. MAINTAIN MACHINERY WITH CARE. Keep blades sharp and clean for best and safest performance.
Follow instructions for lubricating and changing accessories.
16. MAKE SURE GUARDS ARE IN PLACE AND WORK CORRECTLY BEFORE USING MACHINERY.
17. REMOVE ADJUSTING KEYS AND WRENCHES. Make a habit of checking for keys and adjusting
wrenches before turning machinery ON.
18. CHECK FOR DAMAGED PARTS BEFORE USING MACHINERY. Check for binding and alignment
of parts, broken parts, part mounting, loose bolts, and any other conditions that may affect
machine operation. Repair or replace damaged parts.
19. DO NOT FORCE MACHINERY. Work at the speed for which the machine or accessory was
designed.
20. SECURE WORKPIECE. Use clamps or a vise to hold the workpiece when practical. A secured
workpiece protects your hands and frees both hands to operate the machine.
21. DO NOT OVERREACH. Keep proper footing and balance at all times.
22. MANY MACHINES WILL EJECT THE WORKPIECE TOWARD THE OPERATOR. Know and avoid condi-
tions that cause the workpiece to "kickback."
23. BE AWARE THAT CERTAIN DUST MAY BE HAZARDOUS to the respiratory systems of people and
animals, especially fine dust. Make sure you know the hazards associated with the type of dust
you will be exposed to and always wear a respirator approved for that type of dust.

-8-
M1111 Mill with Dovetail Column
SAFETY
Additional Safety for Milling Machines
USE this and other machinery with caution
and respect. Always consider safety first,
as it applies to your individual working
conditions. No list of safety guidelines can
be complete—every shop environment is
different. Failure to follow guidelines could
result in serious personal injury, damage
to equipment or poor work results.
READ and understand this
entire instruction manual
before using this machine.
Serious personal injury
may occur if safety and
operational information is
not understood and fol-
lowed. DO NOT risk your
safety by not reading!
1. UNDERSTANDING CONTROLS. Make sure you understand the use and operation of all controls.
2. SAFETY ACCESSORIES. Always use the chip guard in addition to your safety goggles when milling to
prevent bodily injury.
3. HOLDING WORK. Before starting the machine, be certain the workpiece has been properly
clamped to the table. NEVER hold the workpiece by hand when using the mill.
4. CHUCK KEY SAFETY. Always remove your chuck key, drawbar wrench, and any service tools imme-
diately after use.
5. SPINDLE SPEEDS. Select the spindle speed that is appropriate for the type of work and material.
Allow the mill to gain full speed before beginning a cut.
6. SPINDLE DIRECTION CHANGES. Never reverse spindle direction when milling or boring.
7. BE ATTENTIVE. DO NOT leave mill running unattended for any reason.
8. MACHINE CARE AND MAINTENANCE. Never operate the mill with damaged or worn parts. Maintain
your mill in proper working condition. Perform routine inspections and maintenance promptly. Put
away adjustment tools after use.
9. DISCONNECT POWER. Make sure the mill is turned OFF, disconnected from its power source, and
all moving parts have come to a complete stop before starting any inspection, adjustment, or
maintenance procedure.
10. AVOIDING ENTANGLEMENT. Keep loose clothing articles such as sleeves, belts or jewelry items
away from the mill spindle. Never wear gloves when operating the mill.
11. CUTTING TOOL INSPECTION. Inspect drills and end mills for sharpness, chips, or cracks before
each use. Replace dull, chipped, or cracked cutting tools immediately. Handle new cutting tools
with care. Leading edges are very sharp and can cause lacerations.
12. EXPERIENCING DIFFICULTIES. If at any time you are experiencing difficulties performing the
intended operation, stop using the machine! Contact our Technical Support at [phone].

-9-
M1111 Mill with Dovetail Column
ELECTRICAL
DO NOT work on your electrical system
if you are unsure about electrical
codes and wiring! Seek assistance from
a qualified electrician. Ignoring this
warning can cause electrocution, fire,
or machine damage.
ELECTRICAL
110V Operation
The Model M1111 is designed for a 110V power supply;
however, the motor receives 220V current from the built-
in 110V–to–220V power inverter. We recommend connect-
ing this machine to a dedicated circuit with a verified
ground, using the circuit size below as a minium. Never
replace a circuit breaker with one of higher amperage
without consulting a qualified electrician to ensure com-
pliance with wiring codes.
This machine must be grounded! The electrical cord sup-
plied with this machine comes with a grounding pin. If
your outlet does not accommodate a ground pin, have it
replaced by a qualified electrician.
If you are unsure about the wiring codes in your area
or you plan to connect your machine to a shared cir-
cuit, you may create a fire or circuit overload hazard—
consult a qualified electrician to reduce this risk.
Operating Voltage Amp Draw Min. Circuit Size Plug/Receptacle Extension Cord
110V Operation 12 Amps 15A NEMA 5-15 14 Gauge
Figure 2. 5-15 plug and receptacle.
Electrical Specifications
We do not recommend using an extension cord; however,
if you have no alternative, use the following guidelines:
• Use a cord rated for Standard Service (S).
• Do not use an extension cord longer than 50 feet.
• Ensure that the cord has a ground wire and pin.
• Use the gauge size listed below as a minimum.
Extension Cords
The machine must be properly set up before it is
safe to operate. DO NOT connect this machine to the
power source until instructed to do so in the "Test
Run" portion of this manual.

-10-
M1111 Mill with Dovetail Column
SETUP
Keep machine disconnected from
power until instructed otherwise.
This machine has been carefully packaged for safe trans-
portation. If you notice the machine has been damaged
during shipping, please contact your authorized Shop Fox
dealer immediately.
Unpacking
SETUP
The following is a description of the main components
shipped with the Model M1111. Lay the components out to
inventory them.
Note: If you can't find an item on this list, check the
mounting location on the machine or examine the pack-
aging materials carefully. Occasionally we pre-install cer-
tain components for safer shipping.
Box Inventory (Figures 3 & 4) Qty
A. Assembled Mill/Drill .......................................1
B. Drill Chuck and JT6 x R8 Arbor .........................1
C. Oil Bottle ...................................................1
D. T-Nuts .......................................................2
E. Open-End Wrenches 8-10, 12-14, 17-19mm .......1 ea
F. Drawbar Hex Wrench .....................................1
G. Spindle Spanner Wrench .................................1
H. Chuck Key ...................................................1
I. Hex Wrench Set 3, 4, 5, and 6mm .................1 ea
Inventory
Figure 3. M1111 out of the crate.
AB
Figure 4. Inventory.
E
G
C
F
D
H
I

-11-
M1111 Mill with Dovetail Column
SETUP
• Bench Load: This machine distributes
a heavy load in a small footprint. Some
workbenches or tool tables may require
additional bracing to support both machine
and workpiece.
• Working Clearances: Consider existing and
anticipated needs, size of material to be
processed through the machine, and space
for auxiliary stands, work tables or other
machinery when establishing a location for
your mill.
• Lighting: Lighting should be bright enough
to eliminate shadow and prevent eye strain.
• Electrical: Electrical circuits must be
dedicated or large enough to handle
amperage requirements. Outlets must be
located near each machine, so power or
extension cords are clear of high-traffic
areas. Follow local electrical codes for
proper installation of new lighting, outlets,
or circuits.
MAKE your shop “child
safe.” Ensure that your
workplace is inaccessible
to youngsters by closing
and locking all entrances
when you are away. NEVER
allow untrained visitors in
your shop when assem-
bling, adjusting or operat-
ing equipment.
Cleaning Machine
The table and other unpainted parts of your
machine type are coated with a waxy grease
that protects them from corrosion during ship-
ment. Clean this grease off with a solvent clean-
er or citrus-based degreaser. DO NOT use chlo-
rine-based solvents such as brake parts cleaner
or acetone—if you happen to splash some onto a
painted surface, you will ruin the finish.
Machine Placement
USE helpers or power
lifting equipment to lift
this mill. Otherwise, seri-
ous personal injury may
occur.
NEVER use gasoline or
other petroleum-based
solvents to clean with.
Most have low flash
points, which make them
extremely flammable.
A risk of explosion and
burning exists if these
products are used. Serious
personal injury may occur
if this warning is ignored!
ALWAYS work in well-
ventilated areas far from
possible ignition sources
when using solvents to
clean machinery. Many
solvents are toxic when
inhaled or ingested. Use
care when disposing
of waste rags and
towels to be sure they
DO NOT create fire or
environmental hazards.

-12-
M1111 Mill with Dovetail Column
SETUP
Bench Mounting
Four leveling feet have been included with your mill.
However, for greater safety and better performance, your
mill should be bolted to a workbench to provide maxi-
mum rigidity and safety.
Secured Mounting
To mount the mill to the workbench, do these steps:
1. Determine the best position for the mill on the
workbench.
Note: For the best performance, make sure the
cross feed and the longitudinal handwheels extend
out beyond the edge of the table surface. This will
allow unrestricted handwheel operation.
2. Mark your hole locations using the mounting holes in
the base as a guide.
3. Drill the holes needed in the workbench.
4. Place a precision level on the mill table and shim
the mill until it is level side-to-side and front-to-
back.
5. Using appropriate power lifting equipment, place the
mill on the workbench.
6. Bolt the mill base to the top of the workbench
(Figure 6).
Unsecured Mounting
To setup the mill for temporary mounting, do these
steps:
1. Using appropriate power lifting equipment, tilt the
mill and install the four feet into the base.
2. Place the mill on the workbench.
3. Place your precision level on the mill table.
4. Loosen the hex nut(s), as shown in Figure 7, and turn
the feet until the mill is level side-to-side and front-
to-back.
5. Retighten the hex nuts.
Figure 5. Minimum working clearances and
mill mounting bolt pattern.
Figure 6. Example of a through mount
setup.








Figure 7. Leveling the mill.

-13-
M1111 Mill with Dovetail Column
SETUP
Test Run and Spindle
Break-In
The Model M1111 spindle speed can be set from 100–1750
RPM. You must follow the proper break-in procedures to
ensure the spindle bearings break-in and seat before put-
ting a load on the machine.
To test run and break-in the spindle bearings, do these
steps:
1. Do all lubrication procedures highlighted in
Lubrication in MAINTENANCE on Page 24.
2. Make sure there are no obstructions around or under-
neath the spindle.
3. Remove the drawbar if there is no arbor or collet in
the spindle.
4. Make sure all switches are OFF and connect the mill to
the power source.
5. Turn the main power switch ON, and push the START
button on the control panel. The spindle will begin to
turn at a low RPM.
6. Now push the + button until the mill reaches approxi-
mately 600 RPM, then let it run for a minimum of 10
minutes.
—If you suspect the mill is not working correctly,
shut the mill OFF, disconnect it from power, and
use the Troubleshooting table on Page 25 to cor-
rect the problem before proceeding further.
—If the mill is running smoothly, proceed to Step 7.
7. Increase the speed to 1000 RPM and let it run for
another ten minutes.
8. Increase the speed to 1750 RPM and let it run for
another ten minutes.
9. Turn the mill OFF.
10. Set the spindle to rotate in the opposite direction,
and let it run at 1750 RPM for another ten minutes.
Failure to follow start up and spindle
break-in procedures will likely cause
rapid deterioration of spindle and
other related parts.
NOTICE
DO NOT leave the area while break-in
procedure is under way. You must be
ready to stop the machine if any prob-
lem occurs.
NOTICE
Figure 8. Control panel.

-14-
M1111 Mill with Dovetail Column
OPERATIONS
OPERATIONS
General
This machine will perform many types of operations
that are beyond the scope of this manual. Many of these
operations can be dangerous or deadly if performed
incorrectly.
The instructions in this section are written with the
understanding that the operator has the necessary knowl-
edge and skills to operate this machine. If at any time
you are experiencing difficulties performing any oper-
ation, stop using the machine!
If you are an inexperienced operator, we strongly recom-
mend that you read books, trade articles, or seek train-
ing from an experienced mill operator before performing
any unfamiliar operations. Above all, your safety should
come first!
Always wear safety glasses when oper-
ating this machine. Failure to comply
may result in serious personal injury.
DO NOT investigate problems or adjust
the machine while it is running. Wait
until the machine is turned OFF,
unplugged and all working parts
have come to a complete stop before
proceeding!
READ and understand this entire instruc-
tion manual before using this machine.
Serious personal injury may occur if
safety and operational information is not
understood and followed. DO NOT risk
your safety by not reading!

-15-
M1111 Mill with Dovetail Column
OPERATIONS
Spindle Height Control
Figure 9. Spindle controls.
Quill Lock Lever
Spindle height is changed by unlocking the quill lock
and using the down feed handles or the fine feed knob
(Figure 9). The digital spindle height readout indicates
the spindle height.
To change the spindle position, do these steps:
1. Unlock the quill lock lever and loosen the fine feed
lock knob.
Note: Use the comfort lever (Figure 9) for addi-
tional leverage to unlock the fine feed lock knob if
the knob is too tight. Do not use the comfort lever
to tighten the knob.
2. Pull down on the quill feed levers to lower or raise
the spindle. Lock the quill lock to hold the spindle in
a particular position if you choose.
Note: Milling with the quill fully extended, can
cause tool chatter. For maximum spindle rigidity
when milling, lower the headstock, keep the spin-
dle retracted completely with the quill lock lever
locked, and the fine feed lock knob tightened.
Comfort Lever
Quill Feed Lever
Spindle
Figure 11. Table locks and scales.
Table Travel
(X-Axis and Y-Axis)
Longitudinal Feed
The longitudinal feed, or X-axis is moved by the
handwheel shown in Figure 10 at the end of the table.
The handwheel will move the table in both directions
side-to-side. One complete revolution of the handwheel
moves the longitudinal feed 0.100". There is also a scale
on the front of the table for use when a tight tolerance is
not required. The longitudinal feed can be locked in posi-
tion by a table lock located on the front of the table (see
Figure 11).
Cross Feed
The cross feed or Y-axis in Figure 10, is moved with the
handwheel on the front of the table base. One complete
revolution of the handwheel moves the cross slide 0.100".
The cross feed can be locked into position by a table lock
located on the right side of the cross slide underneath the
table (see Figure 11).
Figure 10. Table X and Y-axis controls.
Y-Axis Handwheel
X-Axis Handwheel
X-Axis Table Lock Lever
X-Axis Scale
Y-Axis Table Lock Lever
Y-Axis Scale
Fine Feed Lock Knob
Fine
Feed
Knob

-16-
M1111 Mill with Dovetail Column
OPERATIONS
Figure 13. Z-axis control.
Headstock Travel
(Z-Axis and Rotation)
Headstock height is adjustable in the vertical Z-axis to
accept large workpieces. For unique milling operations,
the headstock can be tilted right or left between 0° and
90°. Your mill has a dovetailed slide that allows you to
reposition the headstock and change tooling without los-
ing your alignment with a hole or milling path.
To raise or lower the headstock, do these steps:
1. Unlock the headstock slide lock lever shown in
Figure 12.
2. Turn the Z-axis handwheel shown in Figure 13 to
raise or lower the headstock, then lock the head-
stock slide lock lever.
Note: Milling with the quill fully extended, can
cause tool chatter. For maximum spindle rigidity
when milling, lower the headstock, keep the spin-
dle retracted completely with the quill lock lever
locked, and the fine feed lock knob tightened.
To tilt the headstock to the left or right, do these
steps:
1. DISCONNECT THE MILL FROM POWER!
2. Using a 17mm wrench, loosen both headstock tilt
lock nuts (Figure 14).
3. Insert a 6mm hex wrench into the index pin release
port (Figure 14), and turn the hex wrench clockwise
to disengage the spring-loaded index pin from the
headstock.
4. While watching the tilt scale, rotate the headstock
to the required angle, and retighten the tilt lock
nuts to hold the headstock in place.
Note: The index pin is spring loaded and serves
only as a quick way to return the headstock close
to zero. It is not intended to be an absolute zero
degree stop. No other index holes exist at other
angles in the headstock.
Figure 12. Headstock slide controls.
Headstock Slide
Lock Lever
Figure 14. Headstock tilt controls.
Headstock Tilt
Lock Nut
Tilt Scale
Index Pin
Release Port
Z-Axis Handwheel

-17-
M1111 Mill with Dovetail Column
OPERATIONS
Drill Chuck
Figure 16. Tapping on the drawbar.
Figure 15. Spindle holes.
Holes Under Spindle
To remove the chuck and arbor from the spindle, do
these steps:
1. DISCONNECT THE MILL FROM POWER!
2. Remove the drawbar safety cap (Figure 16).
3. Lock the quill in place with the quill lock.
4. Insert the pin spanner (Figure 15) into the two holes
at the bottom of the spindle and hold the spindle.
5. Using the 17mm wrench, loosen the drawbar one
turn only. DO NOT remove it. DO NOT completely
unscrew the drawbar before striking it with the ham-
mer, or you will damage the threads on the drawbar
and the arbor.
6. Tap the top of the drawbar with the hammer. This
will unseat the taper of the arbor from the spindle
(see Figure 16).
7. Hold one hand under the chuck and finish loosening
the drawbar by hand until it falls out of the spindle.
Note: The chuck is attached to the arbor using a JT6
taper. This attachment is considered to be semi-
permanent. There should be no need to remove the
chuck from the arbor. Inspect the chuck from time
to time to make sure it is still tight on the arbor.
If it is loose, use a dead-blow or other soft headed
hammer to re-seat the taper.
To install the drill chuck and arbor, do these steps:
1. DISCONNECT THE MILL FROM POWER!
2. Insert the chuck arbor into the spindle so it engages
the alignment pin inside of the spindle and makes
contact with the drawbar threads.
3. While supporting the chuck with one hand, thread
the drawbar into the arbor until the arbor seated up
into the spindle taper.
4. Snug the drawbar with the drawbar hex wrench.
Note: Do not overtighten the drawbar.
Overtightening makes arbor removal difficult and
will damage the arbor and threads.
5. Install the drawbar safety cap (Figure 16).
Drawbar
Safety
Cap

-18-
M1111 Mill with Dovetail Column
OPERATIONS
R-8 Collets
Your Model M1111 features an R-8 spindle taper,
which gives the freedom to use standard R-8
collets.
To install the R-8 collet, do these steps:
1. DISCONNECT THE MILL FROM POWER!
2. Unscrew the drawbar cap.
3. Carefully clean the surface of the collet and
spindle taper. Ensure that they are free of
debris and are lightly oiled.
4. Insert the cutting tool into the collet, then
insert the collet up into the spindle taper.
5. Rotate the collet so it engages the align-
ment pin inside of the spindle, then slide the
collet upward until it makes contact with the
drawbar threads.
6. While supporting the tool in the collet with
one hand, thread the drawbar into the collet
until the collet draws up into the spindle
taper.
7. Snug the drawbar with the A 17MM wrench in
your opposite hand.
Note: Do not overtighten the drawbar.
Overtightening makes collet removal difficult
and will damage the drawbar threads, collet,
and the spindle taper. Keep in mind that the
taper keeps the collet and tool in place. The
drawbar simply aids in seating the taper.
LACERATION HAZARD!
Leading edges of end mills
and other cutting tools can
be very sharp. Protect your
hands with gloves or a shop
towel when handling.
To remove the collet, do these steps:
1. DISCONNECT THE MILL FROM POWER!
2. Tighten the headstock lock.
3. Protect the table surface with a piece of
cardboard or hold the cutter/tool with a
shop towel to prevent it from falling out of
the collet.
4. Using the drawbar hex wrench, loosen the
drawbar but DO NOT remove it.
5. Using the brass hammer, tap the drawbar to
unseat the taper.
6. Unscrew the rest of the drawbar by hand
and remove the collet.
Note: When not in use, always remove
collets and cutting tools from the spindle
taper. Oxidation may cause the collet to
seize and make it hard to remove later.