Shoprider XLR14-SS User manual

|User Manual
XLR14-SS K0835
XLR14-CS K0836

2
Disclaimer
This Powerchair is not intended to be used by individuals with physical limitations that could prevent
the user from operating the Powerchair safely. Shoprider ®disclaims all responsibility for any
personal injury or property damage, which may occur as a result of improper or unsafe use of its
products.
Warranty is only valid when genuine Shoprider ® parts are used. All modications on the Powerchair,
unless approved and authorized by Shoprider ®, will automatically invalidate the warranties.
Standard warranty does not extend to consumable items and parties other than the original user.
The preceding guidance is intended to assist you in the safe operation of this Powerchair. If you
should have any questions about the correct operation of your Powerchair, please contact your
authorized Shoprider ®provider.
Make: XLR 14
Pihsiang Machinery Mfg. Co., LTD. Model # P424LE
Serial No.:
Provider Stamp
Doc #300904-154

3
Introduction ................................................................................... 4
Emi Warning ................................................................................... 7
Electromagnetic Interference From Radio Waves .......................... 8
Feature Guide ................................................................................ 9
The Joystick Controller (VR2) ......................................................... 10
Locking / Unlocking The Joystick Controller .................................. 12
Drive / Freewheel Mechanism ........................................................ 13
Main Circuit Breaker ...................................................................... 13
Driving Your Powerchair ................................................................. 14
Tilt System Function ....................................................................... 18
Maintenance Chart ........................................................................ 19
General Maintenance, Storage, Cleaning, And Lubrication ............ 20
Batteries And Battery Charging ..................................................... 22
Troubleshooting ............................................................................. 24
Specications ................................................................................ 26
Warranty ........................................................................................ 28
Notes ............................................................................................. 31
Contents

4
Introduction
This power wheelchair is designed for comfort, safety, stability, and maneuverability with smooth
control for today’s active lifestyle. The XLR 14 helps you regain your mobility and independence.
The following innovations are included in the XLR Mobility Series:
• Mid-wheel drive for maximum maneuverability
• 6-wheel design for ultimate stability
• Full featured suspension system
• Programmable joystick controller
• Deluxe reclining captain seat (some units)
• Adjustable footplate and arm assemblies
• Flat-free tires
• 8A o-board battery charger
• Power tilt seating
• High ground clearance with 14” drive wheel
• Extra long range battery options
This manual contains important information to allow optimal use of the XLR 14 and to ensure
the safety of the user. Please read this manual carefully and thoroughly before using your power
wheelchair and make sure you understand all the instructions. If you have any questions, please
contact your provider or Shoprider ® Mobility, see below:
21184 S. Figueroa St.
Carson, CA. 90745
[phone]
Intended Use
The intended use of the Shoprider®XLR 14 powered wheelchair by Pihsiang Machinery Mfg. Co.,
LTD is to provide mobility solutions to individuals who are limited to a seated position.
Prescription Statement
CAUTION
Federal law restricts this device to sale by or on the order of a practitioner licensed by
the law of the state in which he/she practices.
The nal decision on the type of power wheelchair to be used is the responsibility of the user and
his or her healthcare professional (physician, physical therapist, etc.). Shoprider ®Mobility is not
responsible for the inappropriate selection of a power wheelchair model, its features, or improper
tting of the wheelchair.
Power Wheelchair Safety
Read carefully ALL safety tips to help ensure your safety while using the power wheelchair. Being

5
safe in a wheelchair requires anticipating potential problems, using common sense, maintenance of
equipment, and communicating with assistants.
Symbols
Symbols & key words are used in this manual and apply to hazards or unsafe practices that could
result in personal injury or property damage.
DANGER
Danger indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING
Warning indicates a potentially hazardous situation which, if not avoided, could result
in death or serious injury.
CAUTION
Caution indicates a potentially hazardous situation which, if not avoided, may result in
property damage, minor injury, or both.
Setup and Adjustments for Safety
For maximum safety, a qualied technician must perform the initial setup and all adjustments of this
wheelchair. Incorrect settings could cause injury to the driver, wheelchair, bystanders, or surrounding
property. After the wheelchair has been set-up/adjusted, check to make sure that the wheelchair
performs to the specications entered during the set-up procedure. If the wheelchair does not
perform to specications, re-enter set-up specications. Repeat this procedure until the wheelchair
performs to specications.
Operator Safety
There are many inherent dangers while operating a power wheelchair. Read carefully and observe all
of the precautions below.
DANGER
Cell phones are a vital necessity for your safety, and should be used in case of an
emergency to call for help and to notify loved ones. However, warnings about driving
while talking on cell phones also apply to power wheelchair operation. In addition to
the distraction safety issue, you also have possible electromagnetic interference
(EMI) that can disrupt the control system (see the EMI section for more information).
Do not use a cell phone, walkie/talkie, laptop, or other radio transmitter while
operating your wheelchair.
Lap belts are very important in a wheelchair. Never operate your wheelchair without rst fastening
the lap belt.

6
DO NOT sit on the power wheelchair when riding in a vehicle: instead, transfer to a vehicle seat.
DO NOT transfer onto or from the wheelchair unless the brakes are engaged and the
controls are powered o.
DO NOT ride on streets, roads, or highways except for crossing walkways.
DO NOT attempt to move an occupied power wheelchair between oors using a stairway or
escalator. Use an Elevator to move an occupied power wheelchair between oors.
WARNING:
DO NOT let children play on or operate your power wheelchair.
DO NOT operate the power wheelchair if the unit is in freewheel mode.
DO NOT use the joystick in an erratic manner when traveling up or down an incline.
DO NOT carry passengers or exceed the maximum weight limit.
DO NOT perform weight bearing exercises while in your powered wheelchair. Your powered
wheelchair has NOT been designed or tested as a seat for any kind of weight training. Attempting
to perform weight bearing exercises may exceed the weight limit of the powered wheelchair will void
the warranty, and may cause serious injury.
DO NOT turn o the joystick controller when the power wheelchair is in motion. This will activate the
electromagnetic brakes and could cause damage to the joystick controller.
DO NOT drive over uneven and soft terrain (soft dirt, loose gravel, deep grass).
DO NOT attempt to mount a curb height greater than 1.5”(40mm).
DO NOT exceed any grade over 6º (10%)
ALWAYS stop fully before changing forward or reverse direction.
ALWAYS brake in an emergency by releasing the joystick.
ALWAYS use slow speed when going down gradients (move the joystick slowly toward center
position to reduce the speed).
ALWAYS reduce your speed before turning sharply.
ALWAYS try to use a “dropped curb” or “curb cutout” whenever possible.
ALWAYS approach and climb over curbs at slow speed.
ALWAYS approach curbs and gradients at 90 degrees.
ALWAYS keep both feet on the footplate while driving.
ALWAYS make sure the batteries are fully charged before operating the power wheelchair.
ALWAYS charge the power wheelchair in a well-ventilated area.
ALWAYS power o the power wheelchair before performing non-weight bearing exercises. Failure to
do so could result in injury.

7
ALWAYS check that the drive wheels are engaged and not in freewheel mode.
ALWAYS keep your power wheelchair maintained properly.
ALWAYS place the seatback in an upright position whenever negotiating an incline.
CAUTION:
NEVER try to use your power wheelchair beyond its limitations as described in
this manual.
NEVER operate the power wheelchair in the rain: the electronics are not waterproof
and you could lose traction on slippery surfaces.
Tips
• Power wheelchairs can be very quiet--make sure others are aware of your presence.
• Announce yourself at closed doors or blind corners to prevent a collision.
• Avoid tipping - DO NOT place heavy loads on the back of your power wheelchair.
• Avoid reaching out from the power wheelchair to pick up low objects.
• DO NOT lift the power wheelchair by its armrests.
• Keep loose items or lap covers away from the wheels.
• Wear brightly colored clothes when you are outdoors.
• Use optional headlights, reector tape, and/or ashing taillights at night.
Transportation Safety
Before transporting the power wheelchair, switch o the joystick controller and lock the brake. A
power wheelchair must be tightly secured to the oor of a transportation vehicle before departing.
Use the securement points (if available) at the front and at the back of the wheelchair as well as the
anchoring points in the transportation vehicle. A trained and experienced driver must be present to
perform the lifting and anchoring of the wheelchair and ensure owner and wheelchair safety.
DANGER
There are dangers present while using public or private transportation vehicles.
Securement points are provided for unoccupied transport only, if available.
Electromagnetic Interference (EMI)
CAUTION
It is very important that you thoroughly read this information regarding the possible
eects of EMI on your power wheelchair.

8
Tests by the Food and Drug Administration (FDA) have determined that EMI can, under certain
conditions, cause power wheelchairs and scooters to move unintentionally and/or erratically, or
cause unintended release of the brakes. Stronger EMI sources can also permanently damage the
power wheelchair’s control system. The intensity of the interfering EM energy can be measured in
volts per meter (V/m). Each powered wheelchair can resist EMI up to a certain intensity, or “immunity
level.” The higher the immunity level is, the greater the protection against EMI. At this time, current
technology is capable of achieving at least a 20V/m immunity level, which would provide useful
protection from the more common sources of radiated EMI.
WARNING
Although your power wheelchair has been tested to the current standard of 20V/m,
care should be taken to avoid electromagnetic sources.
The sources of radiated EMI can be broadly classied into three types:
Hand-held portable transceivers (transmitters-receivers) with the antenna mounted directly on the
transmitting unit. Examples include: citizens band (CB) radios; “walkie talkies;” security, re, and
police transceivers; cellular telephones; and other personal communication devices.
CAUTION
Some cellular telephones and similar devices transmit signals while they are ON, even
when not being used.
Medium-range mobile transceivers, such as those used in police cars, re trucks, ambulances, and
taxis. These usually have the antenna mounted on the outside of the vehicle.
Long-range transmitters and transceivers, such as commercial broadcast transmitters (radio and TV
broadcast antenna towers) and amateur (HAM) radios.
Note: Other types of hand-held devices, such as cordless phones, mobile devices, laptop computers, AM/FM radios,
TV sets, CD players, cassette players, and small appliances, such as electric shavers and hair dryers, are currently
unlikely to cause problems to your power wheelchair.
EMI radiations from hand-held radio sources (transceivers) are of special concern because they
can be brought close to the power wheelchair’s control system. As the transceiver nears the control
system, EMI energy rapidly becomes more intense. This can be unintentional if someone is not
aware of the hazard. Please observe the warnings listed below to prevent possible interference with
the control system of the power wheelchair.
Note: Adding accessories and components or modifying the unit may change the susceptibility to EMI.
WARNING
DO NOT operate hand-held transceivers (transmitters and receivers), such as CB
radios, or turn ON personal communication devices, such as cellular phones, while
the power wheelchair is turned ON.
Report all incidents of unintended movement or braking on your power wheelchair to a Shoprider ®
provider, and note whether there were sources of EMI nearby.

9
Feature Guide
01. Flip-Back, Height & Width Adjustable Armrest
02. Captain’s Seat
03. Headrest
04. Battery Deck Lid (Not Shown)
05. Interchangeable Color Fenders
06. Freewheel Release
07. Castor Fork (Rear)
08. Rear Stabilizing Castor Wheel
09. Castor Fork (Front)
10. Front Castor Wheel
11. Center Mount Foot Platform
12. Joystick
13. Recline Lever
Labels And Warnings
Fig. 01. EMI-RFI: notes that the unit has
passed FDA testing for 20-V/m performance.
Fig. 02. Read your user manual and
familiarize yourself with additional EMI
information and warnings.
Fig. 03. Battery Connection Diagram:
Illustrates battery orientation and information
on circuit protection devices.
Fig. 04. Freewheel: drive mode = Lever inward;
freewheel/push mode = Lever outward.
Fig. 05. Non-Spillable Battery Type.
Fig. 06. XLR Data Plate.
01
13
05
06
08
09
10
11
12
07
02
03
Model: P424LE (XLR 14)
Manufacturer: Pihsiang Machinery Mfg Co.
Country of Origin: Taiwan
Importer: Shoprider Mobility, Carson CA
Max Speed: 4.1 mph / 6.6 km/h
Max User Weight: 300 lb / 136 kg
Unit Weight (Unloaded): 217 lb / 98 kg
Website: WWW.SHOPRIDER.COM
Max Slope: 6˚
Max recommended Slope: 6˚
N36-45
Figure 01 Figure 02
Figure 03 Figure 04
Figure 05 Figure 06

10
Descriptions
The Seat and Arm Assemblies
The power wheelchair seat is built for comfort, style, and
stability. It may come equipped with a captain seat or pan seat,
which features a reclining back for comfort, ip-up armrests
that provide easy side access for transferring onto and o of
your XLR 14, and a durable long lasting black/gray vinyl seat
cover. These armrests also have a built-in height adjustment
knob that can be used to adjust the arm pad to a
comfortable level for the driver (Item A - Figure 07).
The backrest can be adjusted from 95º to 120º.
This can be accomplished by pulling up on the backrest
adjustment handle (Item B - Figure 07).
Adjustable Footplate
The length and height of the footplate can be adjusted to
maximize your comfort and stability. To adjust the height of
the footplate, loosen and remove the bolt (Item C-Figure 08),
adjust to height and replace. To adjust the length of the foot-
plate, loosen the tightening knobs on both sides of the base
(Item D-Figure 07), adjust the length, and tighten.
Battery Access
Refer to “Battery Access” - Maintenance Section for more information.
Seat Position Adjustment
WARNING
The seat position fore/aft (Forward/Rearward) has been set for optimal stability from
the factory. Modifying the seating position to a location other than has been set from
the factory could reduce the stability of the powered wheelchair, resulting in
serious injury.
CAUTION
The seat height should be adjusted by an authorized Shoprider ®provider only.
Joystick Controller Options
VR2 Joystick Controller Descriptions
The XLR 14 Power Wheelchair comes with a VR2 Joystick, 6 Key Controller (Figure 09) as standard
equipment. The joystick controller provides smooth control of speed and direction with 360
degrees of mobility for ease of operation. The joystick is spring-loaded and automatically returns
to the upright (neutral position) when released. Push the joystick in a given direction to move the
power wheelchair in that direction. The joystick has proportional drive control – the farther it is
Figure 08
Figure 07
C
D
B
A

11
pushed from the neutral position, the faster the wheelchair moves. Maximum speed is limited by
the speed adjustment buttons (increase and decrease). To slow the wheelchair to a STOP, simply
release the joystick.
CAUTION
When learning to drive, select a slow speed and try to drive the wheelchair as slowly
as possible by pushing the joystick forward slightly.
Wheelchair Controller Functions
The following is a quick review of the major functions
Turn the controller power button on.
Forward – push the joystick forward.
Reverse – pull the joystick back.
Turn right – push the joystick to the right.
Turn left – push the joystick to the left.
Stop – release the joystick.
VR2 Joystick Controller
On-O Button: Use this button
to turn the joystick controller
(hereinafter referred to as VR2) on
and o. Do not use this button to
stop the power wheelchair, except
in an emergency.
(Item A-Figure 09)
Battery Gauge: This is a
10-segment display, located on the
face of the VR2. It indicates if the
VR2 is switched on and provides
the state of charge of the battery.
It also indicates any faults in the
power wheelchair electrical system.
Refer to Table 1 for more details.
(Item B-Figure 09)
Horn Button: Press this button to sound the warning horn (Item C-Figure 09).
Maximum Speed Indicator: This is a 5-segment display that indicates the maximum
speed setting selected (Item D-Figure 09).
Speed Decrease Button: Press this button to decrease the maximum speed (Item
Figure 09
A
C
E
D
F
H
B
G

12
E-Figure 09).
Speed Increase Button: Press this button to increase the maximum speed (Item F-Figure 09).
Joystick: The joystick (Item G-Figure 09) controls the speed
and direction of the power wheelchair. Push the joystick in the direction you want to go. The farther
you push the joystick from the neutral position, the faster the power wheelchair will travel. Releasing
the joystick will automatically engage the brakes and stop the power wheelchair.
Note: The controller can be tted to suit either right-or left-handed users. Please contact your
provider for further assistance.
Actuator Control (Item H-Figure 09)
If your XLR 14 Power Wheelchair is equipped with optional power actuators, there will be two
additional keys on the VR2 controller for actuator adjustment. The functions of these keys will dier
depending on the number of actuators installed on the power wheelchair.
One Actuator is Installed on the Power Wheelchair:
1. With the VR2 powered on, press either actuator button to activate actuator adjustment mode.
2. The LED above each actuator button will light up.
3. Push the joystick forward or backward to adjust the actuator to the desired position.
4. Release the joystick to stop actuator adjustment.
5. Press either actuator button to return to drive mode.
6. The LED above each actuator button will go out.
Charging Port VR2
Use this port to charge the power wheelchair battery. This is the primary charging
port for the XLR 14 and should only be used with a qualified XLR 14 charger certified
by the original manufacturer of the power wheelchair. Do not use this port as a power
supply for any other electrical devices other than the optional USB charger available
from Shoprider ®. Failure to follow these instructions will void the warranty of the
power wheelchair.
Attention!
The power wheelchair controller may be programmed with a lock mode function to prevent
unauthorized use. The locking method is achieved one of two ways, depending on the controller
and programming.
To lock Powerchair controller
1. While the controller is switched on, depress and hold the on/o button.
2. After 1 second the controller will bleep. Now release the on/o button.
3. Push the joystick forward until the controller bleeps.
4. Push the joystick in reverse until the controller bleeps.
5. Release the joystick, there will be a long bleep.
6. The Powerchair controller is now locked.

13
To unlock the Powerchair controller
1. Use the on/o button to switch the controller on.
2. The maximum speed/prole indicator will be rippling up and down.
3. Push the joystick forward until the controller bleeps.
4. Push the joystick in reverse until the controller bleeps.
5. Release the joystick, there will be a long bleep.
6. The Powerchair is now unlocked.
Sleep Mode
If the controller is left on and not used for more than ten minutes, the
controller will automatically “go to sleep”. This is recognized by a slow
intermittent ash of the battery indicator lights. Simply turn the controller
o and back on to reset.
Drive/Freewheel Mode
The drive/freewheel levers are found at the rear of the Powerchair
(Figure 10). These levers will allow you to disengage the
electromagnetic brakes, and allow the unit to be maneuvered by
pushing the chair.
Make sure the VR2 is powered o. To place your power wheelchair
into freewheel mode, pull both drive/freewheel Drive levers outward.
This will disengage the electromagnetic brakes. To return the power
wheelchair to drive mode, push both levers inward. Press the on/o
button to power on the VR2. If the battery gauge is not ashing, proceed to drive your chair as
normal. If the power chair does not move when the joystick is moved in any direction, then double
check that the drive/freewheel levers have been engaged fully in the inward position.
Main Circuit Breaker
The main circuit breaker is a safety device that will trip to protect the motor and electronics when
they are subjected to excessive loads. It is located at the top-rear (left side) of the unit and can be
reset, should a trip occur.
If a circuit breaker trip occurs, allow the power wheelchair to rest for approximately 1 minute before
depressing the circuit breaker button. Should frequent circuit breaker trips occur, please contact
your Shoprider ®provider.
Preparing To Use Your Power Wheelchair
CAUTION
The XLR 14 is designed to assist with your individual mobility needs. Any usage
outside of the guidelines in this manual may result in damage to the chair or injury to
the user or third party.
Figure 10

14
First Time Use
Before using your XLR 14 power wheelchair for the rst time, you must charge the batteries fully
(refer to Battery Charging Instructions). It is recommended to charge your batteries for 12 hours.
Charging the batteries completely prior to rst time use will increase battery eciency and
battery life.
Before you operate your power wheelchair, check all systems
WARNING
Proper training on safety, operation, and maintenance are essential and can
potentially decrease the frequency of power wheelchair breakdowns and accidents.
Tips
• Inspect the XLR 14, making sure it is clean and ready for use.
• Keep loose items or lap covers away from the wheels.
• Turn o the joystick controller when you have nished using the power wheelchair and
immediately charge the battery.
XLR 14 Power Wheelchair Operation
To safely handle the XLR 14, pay close attention to your surroundings. Scan ahead and look for the
best path to take. Are there obstacles in the path or is it smooth and level? If there are obstacles,
how will you avoid them? Now is the time to put into use all that you have learned from your provider
training and this XLR 14 User Manual. It is important to practice these safety techniques until you are
comfortable in maneuvering around frequently encountered obstacles.
Recommended Driving Surfaces
The XLR 14 is intended to be operated on dry, level surfaces composed of concrete, asphalt, or
blacktop. Care should be taken on soft gravel, or dirt, and wet grass, please refer to additional
warnings under “Wet/Slippery Surfaces”
CAUTION
Before you begin to venture outside or away from your home, practice and master the
safety procedures and techniques involved in safe operation of your power
wheelchair. Have an experienced assistant help you before attempting to operate the
power wheelchair alone.
CAUTION
Keep your arms on or inside the armrests and feet on the footplate at all times
during operation. The handling and maneuverability characteristics of mid-wheel
drive power wheelchairs are inherently dierent from rear- or front-wheel drive power
wheelchairs. If you have used other types of wheelchairs, handling and

15
maneuverability dierences will be most noticeable when traveling over rough terrain
or when negotiating ramps and slopes. To determine and establish your particular
safety limits, practice use of this product on various sloping surfaces in the presence
of a qualied attendant before attempting active use of this power wheelchair.
WARNING
Do not use a cell phone, walkie/talkie, laptop, or other radio transmitter while operating
your wheelchair.
Using the Joystick Controller
Note: For more information, see the descriptions in the Joystick Controller Options section.
CAUTION
When learning to drive, select a slow speed and try to drive the wheelchair as slowly
as possible by pushing the joystick forward only slightly.
Weight Limitations
Your power wheelchair is rated for a maximum weight capacity. Please refer to the specications
table for this limit. Keep in mind that the maximum weight capacity includes the combined weight of
the user and any accessories mounted to the power wheelchair.
WARNING
Do not carry passengers on your power wheelchair. Carrying passengers may aect
the center of gravity, resulting in a tip over or fall.
Transferring Onto or O the Power Wheelchair
WARNING
Always fasten the lap belt when operating your power wheelchair; the lap belt is there
for safety and protection.
Before you transfer onto or o the power wheelchair, engage the drive/freewheel levers in drive
mode and power the joystick controller o. It can be dangerous if you bump into the joystick when
the power is on. When you are sitting or traveling in your wheelchair, always maintain your center of
gravity. Use a positioning belt if there is one available. For maximum safety, practice your transfer
onto and o of the wheelchair. All practice moves should be under the supervision of a trained
assistant. Do not stand on the footplate. Ensure armrests and footplate have been moved out of the
way before transferring onto or o the wheelchair.

16
Ramps and Slopes
WARNING
Always reduce your speed when driving down slopes to maintain stability and avoid
hard braking. Move the joystick slowly toward the center position to reduce speed. If
stopping is necessary, release the joystick and allow the power wheelchair to come
to a full stop.
Ramps are designed for negotiating steps or other obstacles with a manual or power wheelchair.
Inspect the ramp periodically for wear and loose or damaged parts and repair or replace if
necessary. Properly designed ramps will have “edge protection” along each side to prevent the
wheelchair from falling o the ramp. Make sure the ramp is secured in place and does NOT exceed
any grade greater than 6º (10%). Approach a ramp or slope straight on – not at an angle.
WARNING
If your power wheelchair is equipped with a reclining seat-back, do not attempt to
negotiate a steep grade with the back in a reclined position.
When driving down a ramp or slope, keep the chair’s speed to the lowest setting to ensure
controlled descent. If the power wheelchair starts to increase speed, release the joystick and the
chair will slow down and stop. Then, push the joystick forward slightly to continue down the slope
at a controlled speed.
DANGER
Shoprider
®Mobility recommends that you do not attempt to negotiate a slope greater
than 6º (10%). Driving conditions may change quickly, and exceeding the maximum
slope can place the power wheelchair in an unstable situation.
When climbing a ramp or incline, try to keep the power wheelchair moving. If you stop and start up
again, you will lose momentum and it will be harder to start up again. Special care must be taken
to avoid abrupt or sudden forward movement when you resume climbing a ramp or steep slope to
avoid tipping the chair backwards.
CAUTION
Avoid sudden or erratic action with the joystick when traveling up or down an incline.
Curbs And Sidewalks
CAUTION
DO NOT attempt to negotiate a curb with a height above 1.5”(40mm). When
approaching a sidewalk, look for a curb cutout or a driveway.

17
Wet/Slippery Surfaces
WARNING
NEVER operate the power wheelchair in the rain. It is NOT safe. Drive wheels lose
traction on wet ground or grass. The joystick controller and other power wheelchair
electronics are NOT waterproof.
Lawns are often watered and they can be very slick. Also, the water runo from sprinklers can make
sidewalks, driveways and streets wet and slippery.
Public Streets, Roadways & Crosswalks
DANGER
A public street or roadway is a very dangerous place for a power wheelchair. Use
special caution when crossing a busy street. Obey streetlights and proceed cautiously.
Make sure trac has stopped and that it is safe to proceed across the street.
Cornering Information
Even with front and rear caster wheels, excessive speed when cornering can cause the power
wheelchair to lose control and tip over. Reduce your speed and steering angle to lessen the
sharpness of the turn.
Stairs and Escalators
DANGER
Never use your power wheelchair to negotiate stairs or escalators.
Do not try to use escalators, because they pose a serious danger to a power wheelchair. If an
elevator is available, you may safely enter and use it to reach upper or lower oors.
Power Wheelchair Stability
Do not operate the power wheelchair in any direction while leaning forward in the chair. If an object
is to be picked up from the oor, the caster wheels must be positioned to support the chair. Drive
past the object, and then reverse so that the front casters are in the forward position. This position
will provide the power wheelchair with the greatest stability for this operation. Do not lean out of the
chair, because this will cause instability. Keep your arms on or inside the armrests and your feet on
the footplate at all times.
Note: Proper use, handling, and maintenance of your power wheelchair are critical to your
protection and to avoiding injury. Turn o the VR2 after you have nished using your power
wheelchair and charge the battery.

18
Tilt System Usage
The XLR 14 may be equipped with an actuator driven Tilt System as prescribed by your Therapist or
Physician. To activate the Tilt System, select the actuator mode on the VR2 6 Key Joystick
(Figure 11). Once activated, move the joystick in the direction you wish you tilt (Standard setting is
pull back to Tilt backwards, Push forward to return seating to an upright position).
There are two drive modes that will be engaged when the seat is tilted to given angles.
At an angle of 20º the unit speed will enter a reduced drive mode of 25% of the top speed. When
titled to an angle of 25º or greater will engage a drive lock out which will prevent driving altogether.
When the Joystick is returned to Drive Mode, the Speed Indicator will ash to advise that the unit is
in either Reduced Drive or Drive Lockout modes.
Note - Tilt and Inhibit angles may vary slightly due to manufacturing tolerances. Inhibit
angles are xed and cannot be modied.
Pinch points can cause minor to serious injury.
Be mindful of potential pinch points and use caution when using this product.
Actuator Mode Switch
Figure 11
25º or Greater, Drive Lock Out20º, Quarter Speed Reduction
Actuator Mode Switch
Speed/Drive lockout Indicator
Pinch Point Pinch Point

19
Maintenance
Caring for the XLR 14 Power Wheelchair
There are some maintenance procedures that can be performed by the user, if he/she is able. These
procedures include equipment inspection, cleaning, and servicing of the power wheelchair. All other
maintenance and repair must be performed by a provider with a trained and certied technician.
CAUTION
Please follow the procedures and precautions in this manual carefully. Failure to
adhere to these instructions can result in equipment damage or personal injury.
CAUTION
During all work on the power wheelchair and electrical system, make sure the circuit
breaker is disconnected (disconnect at least one battery connector).
Inspection
Inspect the power wheelchair on a regular basis, see the Maintenance Chart for periodic
inspection criteria. Regular inspection can spot problems before they can cause breakdown or
other dangerous issues.
CAUTION
Use only parts and accessories authorized by Shoprider ®Mobility. Unapproved tires,
batteries, and other equipment could make your wheelchair unstable or dangerous.
Such use may also void the warranty on the wheelchair.
Seat and Frame
Inspect the seat, armrests, cushions, lap belt, and footplate. Inspect the lap belt carefully - it is there
for your safety. Make sure it is not fraying or damaged and that it is attached securely to the power
wheelchair frame. Inspect the buckle and make sure it locks secure.
Inspect the seat cushions for wear and replace them if necessary. Make sure that the seat is
fastened securely to the frame. Look for missing fasteners or sharp edges on any seat hardware.
Check the footplate assembly and make sure there are no broken or missing parts. Make sure that
your footplate is adjusted properly according to your requirements.
Wheels and Tires
The wheels and tires should be checked periodically for cracks and wear and replaced if necessary.
The condition of the tires depends on how you drive and use your power wheelchair. Because your
tires are at-free tires, there is no need to worry about tire air pressure. Make sure the wheels have
no “sideplay,” wobbling, or utter when turning. Tighten loose wheel bolts and caster nuts on a
regular basis.
Inspect caster assemblies for wear and proper tightness by spinning the wheel and observing for
free movement or wobble of the wheel. Beware of caster utter, side-to-side motion, which may

20
occur at high speeds. If the casters utter, replace them immediately.
It is recommended that the driving axles (inside the drive wheel assembly) and caster assemblies be
checked and cleaned occasionally for debris buildup, which will hinder the performance of the unit.
Maintenance Chart
Use the following chart for periodic recommended inspection and adjustments of hardware and
electrical parts and systems:
Inspection Criteria Initially Inspect/Adjust
Monthly
Inspect/Adjust
Bi-Annually
Electrical Connections
Make sure all electrical connections are secure √ √
Check limit switch position √ √
Drive Lockout
Make sure Drive Lockout operate properly √ √
Tilt Mechanism
Make sure Tilt operates properly* √ √
Manual Recline Mechanism
Make sure the Recline operates smoothly and
properly*
√ √
Clothing Guards
Ensure all fasteners are secure (If available) √ √
Arms
Secure but easy to release; make sure adjustment
levers engage properly
√ √
Ensure height adjustment on arms operates and
locks securely
√ √
Armrests
Inspect for rips in upholstery √ √
Make sure armrest pad sits ush against arm tube √ √
Seat And Back Cushion
Inspect for rips √ √
Cleaning
Clean cushions and armrests (see cleaning
instructions on Pg. 21)
√ √