ShowPro LED PAR Hex-18 IP65 User manual

LED PAR Hex-18 IP65
1
User Manual
LED PAR Hex-18 IP65
www.showtech.com.au

LED PAR Hex-18 IP65
2
Table of Contents
1. Safety instructions…………………………………………………………3
1.1 Overhead rigging …………………………………………………….4
1.2 Power Connection …………………………………………………..6
1.3 Cleaning and Maintenance ……………………………………..6
2. Menu Navigation ............................................................7
3. DMX Allocation ...............................................................9
4. Technical Specifications ..................................................12

LED PAR Hex-18 IP65
3
1. Safety Instructions
FOR SAFE AND EFFICIENT OPERATION
Be careful with heat and extreme temperature.
Avoid exposing it to direct rays of sun near a heating appliance.
Do not put it in a temperature below 41°F/5°C, or exceeding 95°F/35°C.
Keep away from humidity, water and dust.
Do not place the set in a location with a high humidity or lots of dust.
Containers with water should not be placed on the set.
Keep away from sources of hum and noise
Such as transformer motor, tuner, TV set and amplifier.
To avoid placing on un-stable location
Select a level and stable location to avoid vibration.
Do not use chemicals or volatile liquids for cleaning
Use a dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt.
NO USER SERVICABLE PARTS INSIDE.
If unit is out of service please contact your point of purchase.
If any troubles arise, remove the power plug and contact your Pro Shop
representative for repair. Do not open the cabinet by yourself, it might result a
danger of electric shock.
Take care with the power cable. Never pull the power cable to remove the plug from
the receptacle, be sure to hold the plug.

LED PAR Hex-18 IP65
4
When not using the unit for an extended period of time be sure to disconnect the
plug form the receptacle.
1.1. Overhead Rigging
This item must be built in a way that it can hold 10 times more of its weight for 1
hour without causing any damages. The installation must be secured with a
secondary safety attachment. The Safety attachment has to be constructed in a way
that no part of the installation can fall down. When rigging, de-rigging or servicing
the fixture staying in the area below the installation place, on bridges, under high
working places and other endangered areas us forbidden. Before taking the device in
operation, the installation must be approved by an expert. The operator has to make
sure that safety-relating and machine-technical installations are approved by a skilled
person once a year.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE.
Including (but not limited to) calculating working load limits, installation material
being used, and periodic safety inspection of all installation material and the
projector. If you lack these qualifications, do not attempt the installations yourself,
but instead use a professional structural rigger. Improper installation can result in
bodily injury and/or damage to property.
IMPORTANT:
If multiple PixPad panels are being rigged together as a larger system, special care
must be taken to ensure total loads are adhered to. A maximum of 10 panels should
be hung under each other, longer drops require further bracing or load support,
please refer to a qualified expert. Horizontally mounted panels should also be picked
up from a minimum of every second panel to properly spread the load.

LED PAR Hex-18 IP65
5
Use only professional trussing system if the item shall be lowered from the ceiling or
high joists. Never let the device swing freely in a room.
CAUTION: Overhead Items may cause serious injuries when crashing down!! If there
is concern about the safety then DO NOT INSTALL the device.
DANGER OF FIRE!
When installing the device, make sure there is no highly-flammable material
(decoration articles, etc) within a distance of min. 0.5m.
Mount the projector with the mounting bracket to your trussing system using an
appropriate clamp.
For overhead use, always install a safety-rope that can hold at least 10 times the
weight of the fixture. You must only use safety –ropes with quick links with screw
cap. Pull the safety-rope through the hole in the mounting bracket and over the
trussing system or a safe fixation spot. Insert the end in the quick link and tighten the
safety screw. The maximum drop distance must never exceed 20cm
A safety rope which already held the strain of a crash or which is defective must not
be used again.
DANGER TO LIFE!
Before taking into operation for the first time, the installation has to be
approved by an expert.

LED PAR Hex-18 IP65
6
1.2. Power Connection
!! CAUTION !!
Never leave this device running unattended!! Every person that is involved with this
item has to be qualified!!
Connect item with main plug. The voltage and frequency must exactly be the same as
stated on the device. The power plug must always be inserted without force.
1.3. Cleaning and Maintenance
Please make sure that safety-relating and machine-technical installations are
inspected by a skilled person once a year.
1. Make sure before installing that all screws are tightly connected and not corroded.
2. There must be no deformations on the housings, fixations and installations spots
3. No damages must be showed on the power supply cables, material fatigue and
sediments
If the exterior of the unit is going to be cleaned, please use moist, lint free cloths.
Never use alcohol or solvents.
The Cooling fan must be cleaned monthly and check to ensure it is free of
obstructions.
To clean the interior of the device please use a vacuum cleaner or an air jet, however
we recommend cleaning the lenses weekly to ensure the best output from your unit.

LED PAR Hex-18 IP65
7
2. Menu navigation
NO.
Menu Level 1
Menu Level 2
Menu Level 3
Remark
1
6
-
C
H
d
1
d
5
1
2
（Default 12CH，d 1）
2
8
-
C
H
d
1
d
5
1
2
3
1
2
C
H
d
1
d
5
1
2
4
C
-
-
C
1
C
2
C
3
C
4
C
5
…
…
…
…
C
6
0
C
6
1
C
6
2
C
6
3
Default：C63
5
P
-
-
P
1
P
2
P
3
P
4
P
5
（Default：P1）
6
S
-
-
S
-
-
1
S
1
0
0
（Default：S100）
7
U
-
-
r
0
2
5
5
g
0
2
5
5
b
0
（Default：
RGBAWP=255）

LED PAR Hex-18 IP65
8
2
5
5
A
0
2
5
5
W
0
2
5
5
P
0
2
5
5
8
d
I
M
O
F
F
d
I
M
1
d
I
M
2
d
I
M
3
Dimmer speed OFF: （
Default：OFF）
Dimmer speed
Mode1(Fast)
Dimmer speed
Mode1(Middle)
Dimmer speed
Mode1(Slow)
9
t
e
M
P
3
2
10
P
A
S
S
O
n
O
F
F
（Default：ON）
If setting pass word to
“On”，need to press “UP
，DOWN，UP，DOWN
，ENTER” to release; if
press wrong, pls press
enter to input again.

LED PAR Hex-18 IP65
9
3. DMX Allocation
6-CH
Function
Value
Percent/Setting
Remark
1
Red
000-255
0~100%
2
Green
000-255
0~100%
3
Blue
000-255
0~100%
4
Amber
000-255
0~100%
Amber/White
5
White
000-255
0~100%
6
Purple
000-255
0~100%
8-CH
Function
Value
Percent/Setting
Remark
1
Dimmer
000-255
0~100%
2
Red
000-255
0~100%
3
Green
000-255
0~100%
4
Blue
000-255
0~100%
5
Amber
000-255
0~100%
Amber/White
6
White
000-255
0~100%
7
Purple
000-255
0~100%
8
strobe
000-010
011-255
NO Function
Strobe slow to fast
12CH
Function
Value
Percent/Setting
Remark
1
Dimmer
000-255
0~100%
2
Red
000-255
0~100%
3
Green
000-255
0~100%
4
Blue
000-255
0~100%
5
Amber
000-255
0~100%
5
White
000-255
0~100%
7
Purple
000-255
0~100%

LED PAR Hex-18 IP65
10
8
strobe
000-010
011-255
NO Function
Strobe slow to fast
9
Manual Color + Color
Temperature
000-010
011-030
031-050
051-070
071-090
091-110
111-130
131-150
151-170
171-200
201-205
206-210
211-215
216-220
221-225
226-230
231-235
236-240
241-245
246-250
251-255
No Function
R 100%, G 0~100%, B 0%
R 100%~0%, G 100%, B 0%
R 0%, G 100%, B 0~100%
R 0% G 100%~0% B 100%
R 0%~100% G 0% B 100%
R 100% G 0% B 100%~0%
R 100% G 0%~100% B
0%~100%
R 100%~0% G 100%~0% B 100%
R 100% G 100% B 100%
A100%
Color temperature1
Color temperature2
Color temperature3
Color temperature4
Color temperature5
Color temperature6
Color temperature7
Color temperature8
Color temperature9
Color temperature10
Color temperature11
10
Auto Programs
000-051
052-101
102-152
153-203
204-254
255
No Function
Auto Program 1
Auto Program 2
Auto Program 3
Auto Program 4
Auto Program 5
11
Auto Speed
000-255
Speed Slow to Fast

LED PAR Hex-18 IP65
11
12
Dim Mode
000-051
052-101
102-152
153-203
204-255
Preset dimmer speed from
display menu
Dimmer speed mode off
Dimmer speed mode1 (fast
speed)
Dimmer speed mode2 (middle
speed)
Dimmer speed mode3 (slow
speed)

LED PAR Hex-18 IP65
12
4. TECHNICAL SPECIFICATIONS
Color 1m LUX 3m LUX 5m LUX 7m LUX 10m LUX
R
G
B
A
W
P
RGBA
RGBW
RGBAW
U V
24934
2770
997.4
508.9
249.3
106.5
44.08
4.898
1.763
0.9
0.44
10652
1184
426
217.4
15
4159
462
166.3
84.9
41.6
1499
166.5
60
30.6
36.5
9344
1038
373.7
190.7
93.4
3649
405.5
146
74.5
c
Please note: Information is subject to change without prior notice ©
Power supply: 100 -240 V AC, 50/60 Hz ~
Fuse: N/A
Power consumption: 154w
Light Source: LED 6 IN 1 (10W 120°)
Beam Angle: 21.88°
Dimensions (LxWxH): 328 x 125.4 x 336.8 mm
Weight: 6kg
Maximum ambient temperature Ta: 45° C
Maximum housing temperature TC (steady state): 50°
Please note: Information is subject to change without prior notice ©