ShowPro NEPTUNE 200 BEAM User manual

NEPTUNE 200 BEAM
USER MANUAL
NEPTUNE 200 BEAM
SS673
®

410 mm
482mm
280 mm
412 mm
315 mm
LEDMOV620
410×280×482(mm)
22KG
180W
AC100~240VAC,50/60Hz
2.2A
-20℃~45℃
1.7°
DMX512/RDM/ArtNet/sACN
1
1
Product Introduction
1.1 Specification
Product Code
imensonD
Weight
Rated Power
Input Voltage
Frequency Range
Ambient Temperature
Beam Angle
Control Mode

2
IMPORTANT
ATTENTION
Caution, risk of electric shock
The light source contained in this luminaire shall only be replaced
by the manufacturer or his service agent or a similar qualified person.
1.2 Safety warning
ATTENTION !!
•Avoid shaking or strong impacts to any part of the equipment.
•Always make sure that the power connections are connected correct and secure.
•This product left the place of manufacture in perfect condition. In order to maintain this condition and for safe
operation, the user must always follow the instructions and safety warnings described in this user manual.
•Make sure that all parts of the equipment are kept clean and free of dust.
•When transferring the product, it is advisable to use the original packaging in which the product left the factory.
•Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent that their
effectiveness is impaired.
•The lamp (LED) shall be changed if it has become damaged or thermally deformed.
•If there is any malfunction of the equipment, contact your distributor immediately.
•Always operate the equipment as described in the user manual.
•Always make sure that the supporting structure is solid and can support the combined weight of the products.
•Always disconnect the power supply before attempting and maintenance.
•The earth wire must always be connected to the ground.
•The product must always be placed in a well ventilated area.
•A minimum distance of 0.5m must be maintained between the equipment and combustible surface.
•This product must be installed by a qualified professional.
•Do not touch the power cables if your hands are wet.
•Do not stand close to the equipment and stare directly into the LED light source.
•Always make sure that the equipment is installed securely.
Always read the user manual before operation.
Please confirm that the power supply stated on the product is the same as the mains power supply in your area.

3
2.1 Mounting
2 Installation
The fixture can be mounted in any position.
Always ensure that mounting surface can withstand 10 times the weight of the
fixture.
Always use a safety cable when mounting the fixture in any elevated position.
UPRIGHT
HANGING
2.2 Fuse replacement
● Remove the safety cap by a screwdriver.
etch the old fuse from safety cap.● F
nstall a new fuse. ● I
nstall the safety cap.● I
Safty cap
Fuse

4
Enter
Back
Down
Up
2.3 Power connections
This product uses input and output power cable is 1.5 square mm copper wire
Note:
If the signal cable is over 60m between the DMX512 controller and fixture or beween two fixtures, then a DMX signal amplifier is
needed as well.
3.1 Display operation
3 Display panel operation
ŸUp：Scroll 'UP' through the menu list or increase the value of the current function.
ŸDown：Scroll 'DOWN' through the menu list or decrease the value of the current function.
ŸLeft(Back)： When the Scroll through the main menu or exit from the current sub-menu (press and hold to turn off power).
display screen is off, you can long press 3~ seconds to start the display screen,Enter the password "up down up down" 5
to enter the display Settings.
ŸRight(Enter)：Enter the currently selected menu or confirm the current function value.

5
3.2 Menu
MENU
ADDRESS
PERSON
RUNMODE
001-512
BASIC
STANDARD
EXTEND
DMX512
ARTNET
sACN
AUTO
CUSTOM1
CUSTOM2
OPTION
BACKOUT
PAN INVERT
TILT INVERT
OFF/ON
DIM4
DIM3
DIM2
DIM1
OFF
DIMMER
LED PWM
1200Hz
2400Hz
4000Hz
6000Hz
25000Hz
DMX ERROR
SAVE/BLACK
DISPLAY ON
OFF/ON
DISPLAY LOCK
OFF/ON
OFF/ON
LOAD PARA
NO/YES
SETTING RECOVERY ****
****
****
YES/NO
NET SWITCH
UNIVERS
IP MODE
CLEAN EDIT 1
CUSTOM IP
CLEAN EDIT 2
WDMX HIDE
NETWORK
XXX
DEFAUL IP/CUSTOM IP
XX.XX.XX.XX
ARTNET TO DMX

6
EDIT
STEP(01-30)
EDIT 1-2
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~25
0~255(×0.1S)
YES/NO
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~25
PAN
TILT
PT SPEED
COLOR
ROTA.GOBO
GOBO.ROTA
PRISM1
PRISM2
FOCUS
DIMMER
STROBE
TIME
USE
MANUAL AUTO TEST
CHANNEL
OFF/ON
PAN
TILT
PT SPEED
COLOR
ROTA.GOBO
GOBO.ROTA
PRISM1
PRISM2
FOCUS
DIMMER
STROBE
DEBUG HIDE
RESET
YES/NO
ALL RESET
PT RESET
INFO
UID
LABEL
0x388Axxxxxxxx
NEPTUNE 200 BEAM
FIXTURE HOURS
LED USE HOURS
TEMPERATURE
VERSION
NETWORK
RDM
PT ENCODER
WDMX RESET
SIGNAL
OFF/ON
NO/YES
ONLY XLR
XLR FIRST
ONLY WDMX
WDMX FIRST
COLORGOBO RESET
PRISMFOCUS RESET
WDMX TO DMX

7
MEMORY IC
ANGLESENSOR
PAN SENSOR
PAN ENCODER
PAN DRIVEIC
TILT SENSOR
TILTENCODER
TILTDRIVEIC
TEMPERATURE
COLOR RESET
GOBO RESET
RGOBO RESET
FOCUS RESET
PRISM1 RESET
PRISM2 RESET
****
SERVICE
SYSTEM ERROR
PAN
TILT
COLOR
ROTA. GOBO
GOBO.ROTA
FOCUS
PRISM1
PRISM2
OTHER
±127
±127
±127
±127
±127
±127
±127
±127
±127

MENU
MENU
8
ADDRESS
001-512
PERSON
BASIC
STANDARD
EXTEND
3.3 DMX Address
•【 】Enter Up/Down select 1~512 address.
•Enter the【DMX】mode to set the DMX address.
•Enter【MENU】return.
3.4 Personality(Person)
•Enter the【PERSON】mode to select DMX mode:【 TANDRAD】,【 ASIC】,【EXTEND】.S B
3.5 Runmode
•Press【ENTER】accept,Press【MENU】return.
•【RUNMODE】menu, select required run mode,There are six modes inside:
【DMX512】DMX512 Mode,
【ARTNET】Artnet Mode,
【ARTNET To DMX】ARTNET to DMX Mode,
【sACN】sACN Mode,【AUTO】Auto run Mode,
【CUSTOM1】Customer self-editing scene mode1,
【CUSTOM2】Customer self-editing scene mode2
Press【DOWN】/【UP】select mode.
MENU
RUNMODE
DMX512
ARTNET
sACN
AUTO
CUSTOM1
CUSTOM2
ARTNET TO DMX

9
3.6 Performance(Option)
ŸChoose【OFF】and【ON】to close and open the 【BLACKOUT】mode.
ŸEnter【OPTION】 into the machine set.
Ÿ【PAN INVERT】menu, select【NORMAL】for normal direction,select【INVERT】for inverted of the PAN direction.
Ÿ【TITL INVERT】menu, select【NORMAL】for normal direction,select【INVERT】for inverted of the TITL direction.
Ÿ【DIMMER】menu for selection of【DIM1/DIM2/DIM3/DIM4/OFF】 special dimming curves.
MENU
PT ENCODER
WDMX RESET
SIGNAL
OFF/ON
NO/YES
ONLY XLR
XLR FIRST
ONLY WDMX
WDMX FIRST
WDMX TO DMX
OPTION
BACKOUT
PAN INVERT
TILT INVERT
OFF/ON
DIM4
DIM3
DIM2
DIM1
OFF
DIMMER
LED PWM
1200Hz
2400Hz
4000Hz
6000Hz
25000Hz
DMX ERROR
SAVE/BLACK
DISPLAY ON
OFF/ON
DISPLAY LOCK
OFF/ON
OFF/ON
LOAD PARA
NO/YES
SETTING RECOVERY ****
****
****
YES/NO
NET SWITCH
UNIVERS
IP MODE
CLEAN EDIT 1
CUSTOM IP
CLEAN EDIT 2
WDMX HIDE
NETWORK
XXX
DEFAUL IP/CUSTOM IP
XX.XX.XX.XX

1 0
Ÿ【LED PWM】 is PWM refresh rate bottom, press UP/DOWN to choose <1200Hz>、
<2000Hz>、<2400Hz>、<6000Hz>、<25000Hz>;
Attention: The gray level of dimming will be reduced as the refresh rate increases.
Ÿ【DMX Error】menu, select【SAVE】to maintain last command in case of DMX error or【BLACK】for blackout.
ŸChoose【OFF】and【ON】to close and open the display open & close mode in menu
【DISPLAY ON】
Ÿ【NETWORK】network setting, press【ENTER】in, Depending on the mode, you can hide unwanted features. For example
Net Switch=Off IP Mode=Defaul.
【UNIVERS】Packet group Settings，output grouping 0~255.
【IP MODE】IP mode setting,【DEFAULTIP】is default IP,【CUSTOM IP】is customer's IP.
【CUSTOM IP EDIT】is customer's IP setting.
Ÿ【WDMX RESET】wireless resetting,use for patch wireless signal,【YES】is Clear the
receiver's message,press again patch wireless signal,【No】do not clear the receiver's message.
Ÿ【SIGNAL】is signal setting, ONLY XLR is wire only, XLR FIRST is wire first, ONLY WDMX is wireless only.WDMX FIRS is
wireless first , WDMX TO DMX is wireless to wired.
Ÿ【LOAD PARA】is Parameter upload Settings, enter【NO】do not upload, enter【YES】upload.
Ÿ【SETTING】Maintain Settings, select【RECOVERY】is restore default factory Settings.
Press【ENTER】 Enter password then press【ENTER】,if your password correct there
will display【OK】.
【CLEAN EDIT1】clean Customer self-editing scene 1, press【ENTER】confirm.
【CLEAN EDIT2】clean Customer self-editing scene 2, press【ENTER】confirm.
【WDMX HIDE】hide wireless mode, WDMX RESET and SIGNAL hide and the default is
wired mode only.
Ÿ【PT ENCODER】XY Encoder switch,【OFF】is close,【ON】is open.
ŸChoose 【OFF】and【ON】to close and open the screen lock mode in menu 【DISPLAY LOCK】

1 1
EDIT
STEP(01-30)
EDIT 1-2
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~25
0~255(×0.1S)
YES/NO
PAN
TILT
PT SPEED
COLOR
ROTA.GOBO
GOBO.ROTA
PRISM1
PRISM2
FOCUS
DIMMER
STROBE
TIME
USE
MENU
3.7 EDIT
ŸNote:if user want to circulate the created steps,please set the last step’s【 】TIME
as 0.
For example,there are 3 steps,the setting should be like belowed:
Step 1 TIME =4 Use【 】 【 】=Yes
Step 2 TIME =5 Use【 】 【 】=Yes
【 】 【 】=YesStep 3 TIME =0 Use
ŸEnter the Edit mode to edit the custom programs by adjusting the value of【 】
【 】 【 】 【 】 【COLOR】 【 】 【 】 【 】 【 】PAN , TILT , PT SPEED , , ROTA.GOBO , GOBO.ROTA , PRISM 1 , PRISM 2 ,
【 】 【 】 【 】 【 】FOCUS , DIMMER , STROBE , TIME .
ŸEnter【 】and select【 】to run the steps user need.Use Yes

1 2
3.8 MANUAL
•【 】set the ：RESET reset
【 LL RESET】 .A menu, select Yes/No to carry out all reset
【PT RESET】 PAN/TILT . menu, select Yes/No to carry out reset
【COLOR GOBO RESET】color wheel、GOBO，press No do not resetting, press Yes resetting.
【PRISM FOCUS RESET】focus、prism，press No do not resetting, press Yes resetting.
•【AUTOTEST】at 【 】 Press【ENTER】into MANUAL .
• No【DEBUG HIDE】is the factory testing mode.All stepper motors are not controlled by signal,It only works again after the reset. enter out、
enter in.Yes
•COLOR color temperature ROTA.GOBO【PAN】pan set,【TILT】 tilt set,【PT SPEED】 set the pan & tilt speed,【 】 ,【 】set the rotating
gobo wheel,【 】set the autogiration of gobo wheell,【PRISM 1】 set the prism 1,【PRISM 2】 set the prism 2,【FOCUS】set GOBO.ROTA
the focusing,【DIMMER】set the dimmer,【STROBE】set the strobe, push the UP/DOWN to set the value【0~25】.
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~25
MANUAL AUTO TEST
CHANNEL
OFF/ON
PAN
TILT
PT SPEED
COLOR
ROTA.GOBO
GOBO.ROTA
PRISM1
PRISM2
FOCUS
DIMMER
STROBE
DEBUG HIDE
RESET
YES/NO
ALL RESET
PT RESET
COLORGOBO RESET
PRISMFOCUS RESET
MENU

1 3
MENU
INFO
UID
LABEL
0x388Axxxxxxxx
NEPTUNE 200 BEAM
FIXTURE HOURS
LED USE HOURS
TEMPERATURE
VERSION
NETWORK
RDM
MEMORY IC
ANGLESENSOR
PAN SENSOR
PAN ENCODER
PAN DRIVEIC
TILT SENSOR
TILTENCODER
TILTDRIVEIC
TEMPERATURE
COLOR RESET
GOBO RESET
RGOBO RESET
FOCUS RESET
PRISM1 RESET
PRISM2 RESET
SYSTEM ERROR
3.9 INFO
ŸPress【ENTER】into【INFO】check information,press up and down
【FIXTURE HOURS】is hours of fixture use;
【LED USE HOURS】is LED use time;
【TEMPERATURE】is led temperature.
【VERSION】is software versions;
【NETWORK 】check network parameter;
【RDM】check fixture's ID.
【SYSTEM ERROR】System information error：Memory IC,Angle Sensor,Pan Sensor,Pan Encoder,Pan Drive IC,Tilt
Sensor,TiltEncoder,TiltDriveIC,Temperature,Color reset,Gobo reset,RGobo reset,Focus reset,Prism 1 reset,Prism 2
reset.

1 4
MENU
****
SERVICE
PAN
TILT
COLOR
ROTA. GOBO
GOBO.ROTA
FOCUS
PRISM1
PRISM2
±127
±127
±127
±127
±127
±127
±127
±127
3.10 SERVICE
ŸPress【ENTER】into【SERVICE】Enter password to enter the options page.
【PAN】Pan position fine adjustment，Push up and down buttons adjust ±127 value.
【TILT】Tilt position fine adjustment，Push up and down buttons adjust ±127 value.
【COLOR】Color position fine adjustment，Push up and down buttons adjust ±127 value.
【ROTA. GOBO】Rotation gobo position fine adjustment，Push up and down buttons adjust±127 value.
【GOBO.ROTA】Gobo self-rotation position fine adjustment，Push up and down buttons adjust±127 value.
【FOCUS】Focus position fine adjustment，Push up and down buttons adjust ±127 value.
【PRISM 1】Prism position fine adjustment，Push up and down buttons adjust ±127 value.
【PRISM 2】Prism position fine adjustment，Push up and down buttons adjust ±127 value.

1 5
000-255
000-255
000-255
000-255
000-255
000-007
008-013
014-019
020-025
026-031
032-037
038-043
044-049
050-055
056-063
064-191
192-222
223-224
225-255
000-255
CH.1
CH.2
CH.3
CH.4
CH.5
CH.1
CH.2
CH.3
CH.4
CH.5
CH.1
-
CH.2
-
CH.3
COLOR WHELL1 9+1
ROTATING GOBO 8+1
PAN 0-540°
PAN FINE
TILT 0-270°
TILT FINE
PT Speed
WHITE
COLOR 1
COLOR 2
COLOR 3
COLOR 4
COLOR 5
COLOR 6
COLOR 7
COLOR 8
COLOR 9
COLOR WHEEL1 0-360°
STOP
COLOR WHEEL FINE
CH.4
-
CH.6
-
CH.6
CH.7
COLOR WHELL1 RAINBOW EFFECT(SPEED 100%->1)
COLOR WHELL1 RAINBOW EFFECT(SPEED 1->100%)
ROTATING WHITE
ROTATING GOBO 1
ROTATING GOBO 2
ROTATING GOBO 3
ROTATING GOBO 4
ROTATING GOBO 5
ROTATING GOBO 6
ROTATING GOBO 7
000-010
011-016
017-022
023-028
029-034
035-040
041-046
047-052
VALUE FUNCTION
4 Using a DMX512 Controller
4.1 Channel Assignment
Note: this product has three DMX512 channel configurations:【BASIC】【STANDARD】【EXTEND】.
EXTEND
(18CH)
BASIC
(12CH)
STANDARD
(15CH)

1 6
053-058
059-066
067-074
075-082
083-090
091-098
099-106
107-114
115-122
123-127
128-190
191-192
193-255
0-120
121-125
126-165
166-170
171-210
211-215
216-255
000-255
0-10
11-145
146-150
151-200
201-205
206-255
0-10
11-145
146-150
151-200
201-205
ROTATING GOBO 8
ROTATING GOBO 1 SHAKE (SPEED 1 —> 100%)
ROTATING GOBO 2 SHAKE (SPEED 1 —> 100%)
ROTATING GOBO 3 SHAKE (SPEED 1 —> 100%)
ROTATING GOBO 4 SHAKE (SPEED 1 —> 100%)
ROTATING GOBO 5 SHAKE (SPEED 1 —> 100%)
ROTATING GOBO 6 SHAKE (SPEED 1 —> 100%)
ROTATING GOBO 7 SHAKE (SPEED 1 —> 100%)
ROTATING GOBO 8 SHAKE (SPEED 1 —> 100%)
WHITE
STOP WATER EFFECT
ROTATING GOBO FLOWING WATER EFFECT (SPEED 100 —> 1%)
ROTATING GOBO FLOWING WATER EFFECT (SPEED 1 —> 100%)
CH.5 CH.7 CH.8
CH.6 CH.8 CH.9
CH.7
CH.8
CH.9
CH.10
CH.11
CH.12
- - CH.10
STOP
STOP
STOP
GOBO ROTATING FINE
ROTATING GOBO ANGLE ADJUSTMENT (0 —> 360°)
ROTATING GOBO SHAKE (SPEED 1 —> 100%)
ROTATING GOBO POSITIVE ROTATION (SPEED 100% —> 1)
ROTATING GOBO REVERSE ROTATION (SPEED 1 —> 100%)
GOBO ROTATING
PRISM 1
PRISM 2
PRISM INSERT AND ADJUST THE ANGLE (0 —> 360°)
PRISM INSERT AND POSITIVE ROTATION (SPEED 100% —> 1)
WHITE
STOP
STOP ROTATION
PRISM INSERT AND REVERSE ROTATION (SPEED 1 —> 100%)
PRISM INSERT AND ADJUST THE ANGLE (0 —> 360°)
PRISM INSERT AND POSITIVE ROTATION (SPEED 100% —> 1)
WHITE
STOP
STOP ROTATION
VALUE FUNCTION
EXTEND
(18CH)
BASIC
(12CH)
STANDARD
(15CH)

1 7
0-9
10-99
100-109
110-179
180-189
190-255
000-010
011-020
021-030
031-040
041-050
051-060
061-070
071-080
081-090
091-100
101-110
111-120
121-130
131-140
FOCUS
FOCUS FINE
DIMMER
DIMMER FINE
NO FUNCTION
STROBE（ FROM SLOW TO FAST）
NO FUNCTION
LIGHTNING STROBE
NO FUNCTION
RANDOM SROBE
NO FUNCTION
PAN/TILT BLACK ACTIVATED
PAN/TILT BLACK DEACTIVATED
PAN INVERT
TILT INVERT
PAN/TILT INVERT OFF
FAN SLOW
FAN NORMAL
FAN FAST
FAN AUTO
DIM4
DIM3
DIM2
DIM1
PRISM INSERT AND REVERSE ROTATION (SPEED 1 —> 100%)
206-255
0-255
0-255
0-255
0-255
VALUE FUNCTION
STROBE
CONTROL
CH.11
CH.12
CH.14
CH.15
CH.17
CH.18
CH.13
CH.14
CH.15
CH.16
CH.11
-
CH.12
CH.13
CH.9
-
CH.10
-
DIM0
1200Hz
2400Hz
4000Hz
6000Hz
25000Hz
ALL RESET
XY RESET
141-150
151-160
161-170
171-180
181-190
191-200
201-210
211-220
EXTEND
(18CH)
BASIC
(12CH)
STANDARD
(15CH)

1 8
VALUE
EXTEND
(18CH)
BASIC
(12CH)
STANDARD
(15CH) FUNCTION
COLOR GOBO SYSTEM RESET
PRISM FOCUS RESET
221-230
231-255