Shure R180 User manual

Model R180 Replacement Cartridge
©2005, Shure Incorporated
27C2947 (Rev. 4)
Printed in U.S.A.
SHURE MODEL R180 REPLACEMENT CARTRIDGE FOR
MODELS 588SDX, 515SDX, 515SBGX, 515SBG–18X, 515SBG–18XF, AND 515BSLX
This kit contains the following:
• One R180 replacement cartridge
• Two pieces of shrink-wrap tubing (for 515SBGX, 515SBG-8X,
515SBG-8XF, and 515BSLX only)
The following tools are needed to replace the cartridge:
• Long-nose pliers (for 588SDX and 515SDX only)
• A soldering iron of 25 to 40 watts
• Wire cutters (for 515SBGX, 515SBG-18X, 515SBG-18XF, and
515BSLX only)
• #4 (.050 in., 1.3 mm) hex wrench (supplied with 515SBGX,
515SBG-18X, 515SBG-18XF, and 515BSLX only)
MODELS 588SDX AND 515SDX
It is recommended that the following procedure be performed on a
table or other flat surface to support the cartridge and case in order
to avoid the possibility of breaking the cartridge leads.
To replace the R180 cartridge in the 588SDX and 515SDX,
proceed as follows:
1. Unscrew and remove the grille (turning counterclockwise).
2. Gently pull out the old cartridge, being careful not to break
the leads.
3. Using a Phillips screwdriver, remove the screws and lock
plate which hold the switch in place.
4. Using long-nose pliers, gently pull out the switch, being care-
ful not to break the leads.
5. Unsolder and remove the leads of the old cartridge from the
switch.
CAUTION: To prevent damage to the switch, soldering iron
between 25 and 40 watts is recommended.
6. Solder the lead closest to the RED dot on the new cartridge
(see wiring diagram above) to the terminal with the YELLOW
lead on the switch.
7. Solder the other lead from the new cartridge to the terminal
with the BLUE lead on the switch.
8. Using long-nose pliers, carefully replace the switch in the
case with the blank terminal on the switch facing towards the
cartridge (to ensure the UP position is ON), being careful not
to pinch the leads.
9. Placing your finger inside the case to support the switch,
secure the switch in place by screwing the non-lockplate
screw on the side of the switch closest to the grille.
10. Gently insert the new cartridge into the case, being careful
not to pinch the leads, and making sure the foam gasket on
the cartridge is above the aluminum ring.
11. Replace and screw on the grille.
12. Replace the lockplate on the side of the switch opposite the
grille, then secure it with the remaining screw.
CARTRIDGE
WIRING DIAGRAM
OFF
GREEN MALE PLUG
GREEN SWITCH
YELLOW RED – HI Z
WHITE – LO Z
ON
BLUE BLACK
TRANSFORMER
2
1
3
TERMINAL HOUSING
COMMON
RED DOT
CARTRIDGE LEADS
SWITCH
GRILLE

2
Models 515BSLX, 515SBGX, 515SBG–18X, and 515SBG–18XF
It is recommended that the following procedure be performed on a
table or other flat surface to support the cartridge and case in order
to avoid the possibility of breaking the cartridge leads.
To replace the R180 cartridge in the 515X Series (except the
515SDX), proceed as follows:
1. Slide the supplied shrink-wrap tubing over both leads on the
R180 replacement cartridge.
2. Using a #4 (.050 in., 1.3 mm) hex wrench, loosen the set-
screw on the base of the grille.
3. Unscrew and remove the grille (turning counterclockwise).
4. Gently pull out the old cartridge, being careful not to break
the leads.
5. Using wire cutters, cut the lead from the old cartridge marked
by the dot as close to the cartridge as possible, so the lead
sticks out from the handle. Mark the cut lead with a small
piece of tape.
6. Strip about 1/4-in. (6 mm) of insulation from the end of the
lead.
7. Take the lead marked with a red dot on the R180 replace-
ment cartridge and splice it to the taped lead, twisting the
stripped ends together.
8. Solder the spliced leads.
CAUTION: To prevent damage to the leads, a soldering iron
of 25 to 40 watts is recommended.
9. Slide the shrink-wrap tubing so it entirely covers the soldered
connection and bare wires. Gently rub the tip of the soldering
iron back and forth along the shrink-wrap tubing until it
shrinks.
10. Using wire cutters, cut the other lead of the old cartridge as
close to the cartridge as possible, so the lead sticks out from
the handle.
11. Strip about 1/4-in. (6 mm) of insulation from the end of the
lead.
12. Take the unmarked lead on the R180 replacement cartridge
and splice it to the second lead of the handle, twisting the
stripped ends together. Solder the leads.
13. Slide the shrink-wrap tubing so it entirely covers the soldered
connection and bare wires. Gently rub the tip of the soldering
iron back and forth along the shrink-wrap tubing until it
shrinks.
14. Gently insert the new cartridge into the case, being careful
not to pinch the leads, and making sure the foam gasket on
the cartridge is above the aluminum ring.
15. Replace and screw on the grille.
16. Using a #4 (.050 in., 1.3 mm) hex wrench, secure the grille by
tightening the setscrew.
CAUTION: Do not torque the setscrew too tightly.
CARTRIDGE
LEADS
SETSCREW
GRILLE
GREEN
GREEN
SHIELD
RED
YELLOW
BLACK
RELAY
BLUE
GREEN
WHITE
DIRECTION TO ACTUATE
SWITCH
CASE GROUND
CARTRIDGE
CARTRIDGE
LEADS
SETSCREW
GRILLE
CARTRIDGE
CASE
GROUND
GREEN
GREEN
WHITE
BLACK
RED
GREEN
MODELS 515SBGX, 515SBG-18X, AND 515SBG-18XF
MODEL 515BSLX
RED DOT
RED DOT
SHURE Incorporated http://www.shure.com
United States, Canada, Latin America, Caribbean:
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: [phone] U.S. Fax: [phone] Intl Fax: [phone]
Europe, Middle East, Africa:
Shure Europe GmbH, Phone: [phone] Fax: [phone]
Asia, Pacific:
Shure Asia Limited, Phone: [phone] Fax: [phone]