Siemens HCP User manual

SiemensSiemens
SiemensSiemens
Siemens IndustryIndustry
IndustryIndustry
Industry,,
,,
,Inc.Inc.
Inc.Inc.
Inc.
BuildingBuilding
BuildingBuilding
Building
TT
TT
Tecec
ecec
echnologies Dihnologies Di
hnologies Dihnologies Di
hnologies Divisionvision
visionvision
vision
P/N 315-034860-13
Intelligent Control Point
Installation Instructions
Model HCP
INTRODUCTION The Model HCP Intelligent Control Point from Siemens
Industry, Inc. provides remote, independent control of
any of the following:
1. A notification appliance circuit (NAC)
2. A telephone zone (XLS only)
3. A speaker zone (25V or 70.7V RMS) (XLS only,
FV2025/2050, FV922/924)
The HCP communicates through the DLC device loop
card of the FireFinder-XLS System, the FS-DLC device
loop card of the FS-250 System, the FC922/FV922,
FC2025/FV2025 periphery FCI2016 Board (250p)
detector circuits, and the FC2050/FV2050, FC924/FV924
FCI2017 periphery board (500p) detector circuits. Each HCP
uses one device address on the device loop.
PROGRAMMING Use the DPU Programmer/Tester to program and test the module.
The HCP may only be assigned addresses 1 to 60. It is recommended to program
the HCP devices first to ensure that enough addresses have been reserved for them.
Other devices may then be assigned to addresses in this range that were not
assigned to an HCP.
Disconnect wire at terminal 1 and 2 on TB1 before programming.
To set the HCP device address:
• Plug the programming cable of the DPU Programmer/Tester into the two-
pin programming points on the HCP. (See Figure 1 for location.)
• Set the device address for the HCP by following the instructions in the DPU
Programmer/Tester Manual, P/N 315-033260.
Each HCP can be assigned a custom message using either the Zeus Programming Tool
(XLS System), the FS-CT2 (FS-250 System), the FC2025/2050, FV2025/2050 FSX2002
Engineering Tool, or the FC922/924, FV922/924 FSX7212 Engineering Tool. Refer to
the Zeus Quick Start Manual, P/N 315-033875, or the FS-250 Programming Manual, P/
N 315-049403, as applicable.
PROGRAMMING
POINTS
DEVICE ADDRESS:
DISCONNECT WIRE AT TERMINAL "1" &"2"
SIEMENS INDUSTRY, INC.
CAUTION
ONTB1BEFOREPROGRAMMING
FLORHAM PARK, NJ, 07932
INSTALLATION INSTRUCTIONS
TB2ONBACKSIDE
P/N 315-034860
SIEMENS
MODEL: HCP
TB1ONBACKSIDE
654321
123456
Figure 1
HCP Intelligent Control Point

Siemens Industry, Inc.
Building Technologies Division
P/N 315-034860-132
COMPATIBILITY The following minimum revisions are required for proper operation of the HCP:
:METSYSSLX:METSYS052-SFMETSYS02SF
CLD0000.00.40CLD-SF05.1
OGISED
IMP0000.00.40CAN81.20502/5202CFxx.xx.14
21-CSP0000.00.70 LENAP0.50502/5202VFxx.xx.06
04-CAZ 0000.80.20 *0000.80.031
SUEZ9100.00.40
ORPSUREBREC
429/229CFxx.xx.14
429/229VFxx.xx.06
htiwelbitapmocTONera0000.42.20.veRdna0000.12.20.veR,0000.90.031/0000.
90.20.veR04-CAZ* .0000.01.031/0000.01.20.veRro0000.80.031/0000.80.20.veRottreveR.PCHeht
WIRING
Remove all system power before installation, first battery then AC. (To power up,
connect the AC first, then the battery.)
Power down the 24 VDC power supply and the input source (ZAC, etc.) before
installing the HCP.
All wiring must comply with national and local codes. All wire must be 18 AWG
minimum, 12 AWG maximum.
Device Loops The HCP communicates with the FireFinder-XLS/FS-250/Desigo FC2025/2050,
FV2025/2050/Cerberus PRO FC922/924, FV922/924 Systems through its addressable
device loops.These loops are connected to the DLC via terminal blocks on the CC-5
or CC-2 cardcage (XLS) or to the FS-DLC via TB3 on the FS-MB/FS-MB2 main board
(FS-250).They may be wired Class A (Style 6) or Class B (Style 4). Figure 2 shows
both wiring types and the connections to the DLC. See the DLC Installation Instruc-
tions, P/N 315-033090, for more information. Figure 3 shows both wiring types and
connections to the FS-DLC. See the FS-250 Installation, Operation and Maintenance
Manual, P/N 315-049353, for more information. Figure 4 shows both wiring types and
connections to the Periphery boards. See the Desigo FC2025/2050 FV2025/2050
Configuration Manual, Document ID A6V10315023, for more information. Figure 5
shows both wiring types and connections to the Periphery boards. See the Cerberus
PRO FC922/924 FV922/924 Configuration Manual, Document ID A6V10333423, for
more information.
HCP Power Supply For FireFinder-XLS Systems, compatible power supplies for the HCP are the PSC-12,
PSX-12, and PAD-4. Wiring should be connected to TB3 on the PSC-12 and PSX-12, or
the auxiliary power supply on the PAD-4.
For FS-250 Systems, the HCP is powered by the NAC circuits and PAD-4. Wiring
should be connected to the NAC circuits on the main board or the auxiliary power
supply on the PAD-4.

Siemens Industry, Inc.
Building Technologies Division
P/N 315-034860-133
HCP
TB1
1
2
HCP
TB1
1
2
HCP
TB1
1
2
12345678
910111213141516
CLASS A WIRING*
NO T-TAPPING ALLOWED
BOTH ZONES MUST BE WIRED AS CLASS A
12345678
910111213141516
CLASS B WIRING**
T-TAPPING ALLOWED
BOTH ZONES MUST BE WIRED AS CLASS B
*OPERATES IN FULL CONFORMANCE WITH STYLE 6 (ULC DCLA)
ZONE 1
DLC LOCATED IN
ONE SLOT OF CC-5 / CC-2
LINE 1
LINE 1
LINE 1 (RETURN)
LINE 1 (RETURN)
LINE 1 (OUT)
LINE 1 (OUT)
ZONE 2
LINE 2
LINE 2
LINE 2 (OUT)
LINE 2 (OUT)
LINE 2 (RETURN)
LINE 2 (RETURN)
NOT USED
NOT USED
NOT USED
NOT USED
**OPERATES IN FULL CONFORMANCE WITH STYLE 4 (ULC DCLB)
HCP
TB1
1
2
HCP
TB1
1
2
HCP
TB1
1
2
HCP
TB1
1
2
HCP
TB1
1
2
HCP
TB1
1
2
HCP
TB1
1
2
HCP
TB1
1
2
HCP
TB1
1
2
ZONE 1 ZONE 2
DLC LOCATED IN
ONE SLOT OF CC-5 / CC-2
HCP
TB1
1
2
HCP
TB1
1
2
4 3 2 1
C
LA
SS
A WIRIN
G
CLASS B WIRING
HCP
TB1
1
2
HCP
TB1
1
2
HCP
TB1
1
2
HCP
TB1
1
2
1+ 1- 2+ 2-
X1401/X1402
X1801/X1802 4 3 2 1
1+ 1- 2+ 2-
Detector circuits on periphery board
for FC922/FV922
,
FC2025/FV2025
X1401/X1402
X1801/X1802
Figure 2
FireFinder-XLS Device Loop
Connections
NOTES
1. Loop resistance 50 ohms
Max with 252 devices on
the loop. Refer to the DLC
Installation Instructions,
P/N 315-033090 if the
number of devices is less
than 252.
2. 12-18 AWG wire.
3. No EOL device required.
4. Supervised, power limited
per NEC 760.
5. All wiring must conform
to national and local
electrical codes.
Figure 3
FS20 Device Loop
Connections
NOTES
1. Loop resistance 180 ohms
max with 252 devices on
loop.
2. 12-18 AWG wire.
3. No EOL device required.
4. Supervised, power limited
per NEC 760.
5. All wiring must conform
to national and local
electrical codes.

Siemens Industry, Inc.
Building Technologies Division
P/N 315-034860-134
CLASS A* INSTALLATION
NO T-TAPPING ALLOWED
CLASS B** INSTALLATION
T-TAPPING ALLOWED
*OPERATES IN FULL CONFORMANCE WITH STYLE 6
(ULC DCLA)
**OPERATES IN FULL CONFORMANCE WITH STYLE 4 (ULC DCLB)
ZONE
1
NOT USED
Loop Circuit
FS-DLC Device
NOT USED
Loop Circuit
FS-DLC Device
HCP
TB1
1
2
HCP
TB1
1
2
HCP
TB1
1
2
LINE 1 (RETURN)
LINE 1 (OUT)
LINE 2 (OUT)
LINE 2 (RETURN)
ZONE
1
LINE 1
LINE 2
HCP
TB1
1
2
HCP
TB1
1
2
TB1
1
2
HCP
DPU Loop Test When performing a loop test with the DPU be sure to apply power to the HCP.
Without power applied to the HCP a blinking “C” will appear on the DPU, indicating
that the HCP is in trouble.
HCP As NAC Module This application uses the principle of polarity reversal to activate notification appli-
ances. Wiring is shown in Figure 4. Connect the HCP output zone wiring to the (+)
and (-) terminals of each notification appliance as shown in Figure 4. For a list of
compatible devices, refer to P/N 315-096363.
When used as a NAC module, the 24VDC provides power for the supervision circuitry
and to the notification appliances when they are activated.The power source must be
power limited. See the HCP Power Supply section (above) for compatible power sources.
The maximum output load that may be connected to an HCP is 1.5A at 24 VDC. If the 24
VDC is lost or the NAC line is broken or shorted while the HCP is in supervisory mode, a
trouble condition displays at the FireFinder-XLS, FS-250 System control panel, the Desigo
FC2025/2050, FV2025/2050 Operating Unit, and the Cerberus PRO FC922/924, FV922/
924 Operating Unit. For FS-250 Systems, the NAC circuit must be set to “always on” in
the panel or FS-CT2 configuration tool. See the Line Resistance table below for the
allowable line resistance for each HCP output circuit.
ECNATSISERENILTIUCRICTUPTUOPCHELBAWOLLAMUMIXAM ECNATSISERENILDNATNERRUCRESIRCDDEIFICEPSROF
MUMIXAM RESIR
CD TNERRUC )spmAni(
)smhOni(ECNATSISERRESIRCD
mhO1.0mhO52.0mhO5.0mhO57.0mhO1smhO5.1
437.233.276.100.133.—
308.205.200.205.
100.1—
268.276.233.200.276.100.1
139.238.276.205.233.200.2
5.69.229.238.257.276.205.2
RESIRNOPCHHCAEROFECNATSISERPOOLMUMIXAM
:
SETON .seriwhtobroferadeificepssecnatsiseR.1 eratahtseilppusCDV42yrailixualacol,A4sdeecxetnemeriuqertne
rruclatotehtfI.2 .desuebyam,4-DAPsnemeiSsahcus,esugnilangisnoitcetorperifrofdetsilLU
NOTES
1. Loop resistance 50 ohms
Max with 252 devices on
the loop. Refer to the FS-
250 Manual, P/N 315-
049353 if the number of
devices is less than 252.
2. 12-18 AWG wire.
3. No EOL device required.
4. Supervised, power limited
per NEC 760.
5. All wiring must conform
to national and local
electrical codes.
Figure 4
FS-250 Device
Loop Connections

Siemens Industry, Inc.
Building Technologies Division
P/N 315-034860-135
*REFER TO PAD-4 INSTALLATION INSTRUCTIONS
,
P/N 315-050217
,
FOR PROPER SETTING OF SWITCH 4. THE AUXILIARY POWER OUTPUT MUST BE CONFIGURED TO “ALWAYS ON”
.
A
LL WIRING MUST COMPLY WITH NATIONAL AND LOCAL CODES.
POSITIVE AND NEGATIVE
GROUND FAULT
DETECTED AT
<500 OHMS FOR
TERMINALS 3-6 ON TB1.
HCP MODULE IS USED FOR
NAC SUPERVISION AND ACTIVATION
FROM
DLC/FS-DLC
DEVICE LOOP
LINE 1
LINE 2
EARTH
HCP HCP
HCP MODULE IS USED FOR
NAC SUPERVISION AND ACTIVATION
SHIELD EARTH
24 VDC
NAC UNITS
SEE P/N 315-096363
24K, W½,5%
EOL RESISTOR
P/N 140-034677 SHIELD
STYLE Y
SUPERVISED STROBEACTIVATION “SPECIALAPPLICATION”
SUPV: 1mA
ACTIVATED: 1.5A MAX
18.8V-28.2V FILTERED FULL WAVE RECTIFIED
POLARITY SHOWN IN ACTIVE STATE
STYLE Z
24K, W, 5%½
EOL RESISTOR
P/N 140-034677
DC INPUT RATED
18.8-28.2VDC
SUPV: 30mA
ACTIVATED: 1.5A MAX
6 5 4 3 2 1
6 5 4 3 2 1
1 2 3 4 5 6
1 2 3 4 5 6
PROGRAMMING
POINTS PROGRAMMING POINTS
D
C INPUT: 18.8-28.2VDC FILTERED FULL WAVE
MODULE INPUT SUPPLY:
XLS: PSC-12 (TB3) or PSX-12 (TB3).
FS-250: FS-250 NAC Circuit.
XLS/FS-250: PAD-4* (TB16), FC2025/2050,
FV2025/2050, FC922/924, FV922/924,
FCI2016/2017-U1 PERIPHERY BOARD AUX
POWER OR UL LISTED REGULATED 24 VDC
POWER SUPPLY (POWER LIMITED).
HCP As Telephone Zone When the HCP is used as a telephone zone module (FireFinder-XLS System only) as
shown in Figure 5, the 24 VDC provides power to the supervision and call-in detection
circuitry. If the 24 VDC is lost, a trouble condition displays on the PMI/PMI-2 of the
FireFinder-XLS.
The HCP provides a dial tone when a Fireman’s Master telephone (FMT) is taken off
hook or when a Portable FireFighter’s telephone (PFT) is jacked in.
Each HCP can support a maximum of 5 phones off hook.Throughout the system, no
more than 10 phones may be off hook at any one time.
The supervised telephone common talk riser starts at the TZC-8B module in the CAB
backbox.The common talk riser connects continuously to each HCP with a 10K end
of line device at the last HCP. Tie the shield of these riser wires together using
terminal 5 of TB2 and isolate them from the system circuits and the earth ground.
Individual phones may not be connected to a riser that is wired to HCPs.TheTZC-8B
zone must be configured for Riser usage in Zeus.
Connect the supervised telephone zone wiring to the HCP with twisted pair cable.
Terminate at the last station with a 75K ohm end of line resistor. As with the com-
mon talk line described in the paragraph above, be sure that the shield is continuous
and isolated from both system circuits and earth ground and that the shields are
connected together using terminal 5 of TB-2.
Figure 5
HCP Used As An NAC Module
The input power and NAC power inputs onTB2 (1-4)
must be connected to the same source.
All HCPs connected to a given DLC/FS-DLC circuit
must reside within a single notification zone.

Siemens Industry, Inc.
Building Technologies Division
P/N 315-034860-136
POSITIVE AND NEGATIVE GROUND FAULT
DETECTED AT <500 OHMS FOR
TERMINALS 3-6 ON TB1.
75K, ¼W, +/-5%
EOL RESISTOR
P/N 140-050797
AT LAST FJ-303
FROM PREVIOUS HCP OR TZC-8B
(100 OHMS MAXIMUM
LINE RESISTANCE)
COMMON TALK RISER
(POWER LIMITED)
SEE TZC-8B INSTALLATION
INSTRUCTIONS, P/N 315-034110,
FOR RISER RATINGS
ELECTRICAL:
INPUT DC SUPPLY: 18.8 - 28.2VDC,
30mA MAX
FILTERED FULL WAVE
NOTES:
1. THE SHIELD ON THE COMMON TALK
LINE MUST BE CONTINUOUS AND
CONNECTED ONLY TO EARTH
GROUND AT CONTROL PANEL.
2. ALL WIRING MUST COMPLY WITH
NATIONAL AND LOCAL CODES.
3. 12-18 AWG OR AS REQUIRED
BY THE LOCAL AUTHORITY
HAVING JURISDICTION.
HCP DC SUPPLY
FROM PSC-12 (TB-3),
PSX-12 (TB-3),
OR PAD-4* (TB16)
75K, ¼W, +/-5%
EOL RESISTOR
P/N 140-050797
AT LAST STATION
10K, 1/2W, +/-5%
EOL RESISTOR
WARDEN’S STATIONS
(FTS SERIES)
SUPERVISED, 24 OHMS MAX
UNSHIELDED, USE TWISTED PAIR SUPERVISED
24 OHMS MAX
UNSHIELDED
USE TWISTED PAIR
FROM DLC DEVICE
LOOP IN CC-5 / CC-2
POWER LIMITED
SHIELD
* REMOVE 10K TERMINATING RESISTORS FROM THE FJ-303sALL
SHIELD
WHITE BLACK
WHITE
SHIELD
SHIELD
TO
EARTH
SHIELD
BLACK
WHITE
BLACK
WHITE
BLACK
HCP HCP
TO
EARTH
FJ-303
1 2 3 4 5 6
6 5 4 3 2 1 6 5 4 3 2 1
1 2 3 4 5 6
FJ-303
LINE 1
LINE 2
PROGRAMMING
POINTS PROGRAMMING
POINTS
++
*REFER TO PAD-4 INSTALLATION INSTRUCTIONS, P/N 315-050217, FOR PROPER SETTING OF SWITCH 4. THE AUXILIARY POWER OUTPUT MUST BE CONFIGURED TO “ALWAYS ON”.
Figure 6
HCP Used As A Telephone Zone
HCP As (70.7V/25V) Speaker Zone in an XLSV System
When the HCP is used as a speaker zone (FireFinder-XLS System only), the 24 VDC
provides power to the supervision circuitry. If the 24 volts is lost or there is an open
or shorted speaker output line, a trouble condition displays on the PMI/PMI-2 of the
FireFinder-XLS.
The 70.7V/25V RMS audio input to the HCP must be power limited, such as from the
ZAC-40.The ZAC-40 supervises the audio connection path to the HCP and provides
up to 40 watts of power.The ZAC-40 can be wired StyleY (Class B) only. Refer to the
ZAC-40 Installation Instructions, P/N 315-035400 for further information. In order to
function properly during degrade mode, the DLC to which the HCP is connected
must be located in the same enclosure as the DAC-NET and ZAC-40 that supply
audio to the HCP.
When the HCP is used as a speaker zone, the output speaker lines are only super-
vised when the zone is not active.The audio output must not be allowed to exceed
25 watts. The approximate decibel loss for the total speaker zone wire length for
various wire gauge sizes is shown in Figure 7 for the 70.7V option and in Figure 8 for
the 25V option. Connect the speaker output as Style Y (Class B) as shown in Figure 9.

Siemens Industry, Inc.
Building Technologies Division
P/N 315-034860-137
HCP As (70.7V/25V) Speaker Zone in a FV2025/FV2050 or FV922/FV924 System
The 70.7V/25V RMS audio input to the HCP must be power limited, such as from the
VCI2001-U1 Amplifier Card.The VCI2001-U1 supervises the audio connection path to
the HCP and provides up to 50 watts of power. The VCI2001-U1 can be wired Style Y
(Class B) or Style Z (Class A). Refer to the VCI2001-U1 Installation Instructions,
Document ID A6V10370410, for further information. In order to function properly
during degrade mode, the periphery FCI2016/2017-U1 to which the HCP is connected
must be located in the same enclosure as the FDNET and VCI2001-U1 that supply
audio to the HCP.
When the HCP is used as a speaker zone, the output speaker lines are only super-
vised when the zone is not active.The audio output must not be allowed to exceed
25 watts.The approximate decibel loss for the total speaker zone wire length for
various wire gauge sizes is shown in Figure 7 for the 70.7V option and in Figure 8 for
the 25V option. Connect the speaker output as Style Z (Class A) or Style Y (Class B) as
shown in Figures 10 and 11.
100
0
-0.05
-0.10
-0.15
-0.20
-0.25
200 300 400 500 600
TOTAL SPEAKER ZONE WIRE LENGTH (FEET)
dB LOSS
700 800 900 1000
SPEAKER LOAD: 25 WATTS AT 70.7V RMS
LOCATED AT END OF RUN
DOES NOT INCLUDE ANY LOSS
IN RISER RUN
APPROXIMATE SPEAKER ZONE WIRE LOSS
IN DECIBELS FOR VARIOUS GAUGE WIRES VERSUS
TOTAL SPEAKER ZONE WIRE LENGTH (FEET),
WHICH IS TWICE THE WIRE RUN LENGTH.
18 AWG
16 AWG
HCP USED FOR 70.7V RMS OPTION
100
0
-.5
-1.0
-1.5
-2.0
-2.5
200 300 400 500 600
TOTAL SPEAKER ZONE WIRE LENGTH (FEET)
dB LOSS
700 800 900 1000
SPEAKER LOAD: 25 WATTS AT 25V RMS
LOCATED AT END OF RUN
DOES NOT INCLUDE ANY LOSS
IN RISER RUN
APPROXIMATE SPEAKER ZONE WIRE LOSS
IN DECIBELS FOR VARIOUS GAUGE WIRES VERSUS
TOTAL SPEAKER ZONE WIRE LENGTH (FEET),
WHICH IS TWICE THE WIRE RUN LENGTH.
18 AWG
16 AWG
14 AWG
HCP USED FOR 25V RMS OPTION
Figure 7 Figure 8
Approximate Speaker Zone Wire Loss — 70.7V Option Approximate Speaker Zone Wire Loss — 25V Option

Siemens Industry, Inc.
Building Technologies Division
P/N 315-034860-138
Figure 9 HCP Used On An XLSV As A 70.7V/25V Speaker Zone
POSITIVE AND NEGATIVE
GROUND FAULT DETECTED
AT <500 OHMS FOR
TERMINALS 3-6 ON TB1.
POSITIVE AND NEGATIVE GROUND FAULT DETECTED
AT <500 OHMS FOR TERMINALS 3-6 ON TB1.
POSITIVE AND NEGATIVE GROUND FAULT DETECTED
AT <500 OHMS FOR TERMINALS 3-6 ON TB1.
SUPERVISED RISER EARTH
SHIELD
SHIELD
HCP
HCP DC SUPPLY FROM
PSC-12 (TB3), PSX-12 (Tb3),
OR PAD-4* (TB16)
FROM DLC
DEVICE LOOP IN CC-5 / CC-2
POWER LIMITED
70.7V/25V RMS SPEAKER UNITS:
SEE COMPATABILITY GUIDE
P/N 315-096363 FOR LIST OF
COMPATABLE SPEAKERS.
DC INPUT RATING 18.8-28.2VDC, 30mA FILTERED FULL WAVE
SUPERVISED BY HCP MODULES
NFPA STYLE Y
AUDIO RISER CONNECTIONS
SUPERVISORY: 14 VDC, 1mA
AUDIO OUTPUT: 70.7/25 VRMS,
40 WATTS MAX
POWER LIMITED
STYLE Z
SUPERVISED SPEAKER ZONE CONNECTIONS
SUPV: 14 VDC, 1mA
ACTIVATED: 70.7 V/25V RMS, 25 WATTS MAX
24K, W, +/-5%½
EOL RESISTOR
P/N 140-034677
EARTH
SHIELD
HCP
STYLE Y
SUPERVISED SPEAKER ZONE CONNECTIONS
SUPV: 14 VDC, 1mA
ACTIVATED: 70.7 V/25V RMS, 25 WATTS MAX
CAPACITOR COUPLED 70.7V/25V RMS SPEAKERS
24K, W½, +/-5%
EOL RESISTOR
P/N 140-034677 EARTH
SHIELD
HCP
24K, W½, +/-5%
EOL RESISTOR
P/N 140-034677
68K, 1/4W, +/-5% EOL RESISTOR ON LAST HCP SPEAKER ZONE DEVICE P/N 140-034728
ALL WIRING MUST COMPLY WITH NATIONAL AND LOCAL CODES.
12345678
910111213141516
ZAC-40 LOCATED IN ONE SLOT OF CC-5/CC-2
654321 654321 654321
123456 123456 123456
LINE 1
LINE 2
PROGRAMMING POINTS
PROGRAMMING POINTS
PROGRAMMING POINTS
68K, 1/4W, +/-5%
EOL RESISTOR
P/N 140-034728
*REFER TO PAD-4 INSTALLATION INSTRUCTIONS, P/N 315-050217, FOR PROPER SETTING OF
SWITCH 4. THE AUXILIARY POWER OUTPUT MUST BE CONFIGURED TO “ALWAYS ON”.

Siemens Industry, Inc.
Building Technologies Division
P/N 315-034860-139
Figure 10 HCP Used On An FV2025/2050 or FV922/924 As A 70.7V/25V Speaker Zone - Class A
POSITIVE AND NEGATIVE
GROUND FAULT DETECTED
AT <500 OHMS FOR
TERMINALS 3-6 ON TB1.
POSITIVE AND NEGATIVE GROUND FAULT DETECTED
AT <500 OHMS FOR TERMINALS 3-6 ON TB1.
POSITIVE AND NEGATIVE GROUND FAULT DETECTED
AT <500 OHMS FOR TERMINALS 3-6 ON TB1.
EARTH
SHIELD
SHIELD
HCP
HCP DC SUPPLY FROM
AUX POWER (X1001)
ON PERIBOARD
FC2016/2017-U1,
OR PAD-4* (TB16)
FROM PERIPHERY
BOARD FCI2016/2017-U1
DETECTOR CIRCUITS
POWER LIMITED
70.7V/25V RMS SPEAKER UNITS:
SEE COMPATABILITY GUIDE
P/N 315-096363 FOR LIST OF
COMPATABLE SPEAKERS.
DC INPUT RATING 18.8-28.2VDC, 30mA FILTERED FULL WAVE
SUPERVISED BY HCP MODULES
NFPA STYLE Y
AUDIO RISER CONNECTIONS
SUPERVISORY: 14 VDC, 1mA
AUDIO OUTPUT: 70.7/25 VRMS,
50 WATTS MAX
POWER LIMITED
STYLE Z
SUPERVISED SPEAKER ZONE CONNECTIONS
SUPV: 14 VDC, 1mA
ACTIVATED: 70.7 V/25V RMS, 25 WATTS MAX
24K, W, +/-5%½
EOL RESISTOR
P/N 140-034677
EARTH
SHIELD
HCP
STYLE Y
SUPERVISED SPEAKER ZONE CONNECTIONS
SUPV: 14 VDC, 1mA
ACTIVATED: 70.7 V/25V RMS, 25 WATTS MAX
CAPACITOR COUPLED 70.7V/25V RMS SPEAKERS
24K, W½, +/-5%
EOL RESISTOR
P/N 140-034677 EARTH
SHIELD
HCP
24K, W½, +/-5%
EOL RESISTOR
P/N 140-034677
ALL WIRING MUST COMPLY WITH NATIONAL AND LOCAL CODES.
VCI2001-U1 AMPLIFIER LOCATED IN ONE AMPLIFIER SLOT OF VCA2002-U1 CARD CAGE
654321 654321 654321
123456 123456 123456
LINE 1
LINE 2
PROGRAMMING POINTS
PROGRAMMING POINTS
PROGRAMMING POINTS
68K, 1/4W, +/-5%
EOL RESISTOR
P/N 140-034728
*REFER TO PAD-4 INSTALLATION INSTRUCTIONS, P/N 315-050217, FOR PROPER SETTING OF
SWITCH 4. THE AUXILIARY POWER OUTPUT MUST BE CONFIGURED TO “ALWAYS ON”. THIS
IS IN REFERENCE TO TERMINALS 2 AND 3 ON TB2.
1234
NOTE: EARTH GROUND MUST BE CONNECTED FOR PROPER GROUND FAULT DETECTION
LINE 4
LINE 3
IF CLASS A
WIRING
SUPERVISED BULK AUDIO RISER

Siemens Industry, Inc.
Building Technologies Division
P/N 315-034860-1310
Figure 11 HCP Used On An FV2025/2050 or FV922/924 As A 70.7V/25V Speaker Zone - Class B
POSITIVE AND NEGATIVE
GROUND FAULT DETECTED
AT <500 OHMS FOR
TERMINALS 3-6 ON TB1.
POSITIVE AND NEGATIVE GROUND FAULT DETECTED
AT <500 OHMS FOR TERMINALS 3-6 ON TB1.
POSITIVE AND NEGATIVE GROUND FAULT DETECTED
AT <500 OHMS FOR TERMINALS 3-6 ON TB1.
EARTH
SHIELD
SHIELD
HCP
HCP DC SUPPLY FROM
AUX POWER (X1001)
ON PERIBOARD
FC2016/2017-U1,
OR PAD-4* (TB16)
FROM PERIPHERY
BOARD FCI2016/2017-U1
DETECTOR CIRCUITS
POWER LIMITED
70.7V/25V RMS SPEAKER UNITS:
SEE COMPATABILITY GUIDE
P/N 315-096363 FOR LIST OF
COMPATABLE SPEAKERS.
DC INPUT RATING 18.8-28.2VDC, 30mA FILTERED FULL WAVE
SUPERVISED BY HCP MODULES
NFPA STYLE Y
AUDIO RISER CONNECTIONS
SUPERVISORY: 14 VDC, 1mA
AUDIO OUTPUT: 70.7/25 VRMS,
50 WATTS MAX
POWER LIMITED
STYLE Z
SUPERVISED SPEAKER ZONE CONNECTIONS
SUPV: 14 VDC, 1mA
ACTIVATED: 70.7 V/25V RMS, 25 WATTS MAX
24K, W, +/-5%½
EOL RESISTOR
P/N 140-034677
EARTH
SHIELD
HCP
STYLE Y
SUPERVISED SPEAKER ZONE CONNECTIONS
SUPV: 14 VDC, 1mA
ACTIVATED: 70.7 V/25V RMS, 25 WATTS MAX
CAPACITOR COUPLED 70.7V/25V RMS SPEAKERS
24K, W½, +/-5%
EOL RESISTOR
P/N 140-034677 EARTH
SHIELD
HCP
24K, W½, +/-5%
EOL RESISTOR
P/N 140-034677
68K, 1/4W, +/-5% EOL RESISTOR ON LAST HCP SPEAKER ZONE DEVICE P/N 140-034728
ALL WIRING MUST COMPLY WITH NATIONAL AND LOCAL CODES.
VCI2001-U1 AMPLIFIER LOCATED IN ONE AMPLIFIER SLOT OF VCA2002-U1 CARD CAGE
654321 654321 654321
123456 123456 123456
LINE 1
LINE 2
PROGRAMMING POINTS
PROGRAMMING POINTS
PROGRAMMING POINTS
68K, 1/4W, +/-5%
EOL RESISTOR
P/N 140-034728
1234
SUPERVISED BULK AUDIO RISER
IF CLASS A
WIRING
NOTE: EARTH GROUND MUST BE CONNECTED FOR PROPER GROUND FAULT DETECTION
*REFER TO PAD-4 INSTALLATION INSTRUCTIONS, P/N 315-050217, FOR PROPER SETTING OF
SWITCH 4. THE AUXILIARY POWER OUTPUT MUST BE CONFIGURED TO “ALWAYS ON”. THIS
IS IN REFERENCE TO TERMINALS 2 AND 3 ON TB2.
LINE 4
LINE 3