Siemens 7SC80 User manual

C53000-L2040-C353-3
SIPROTEC Compact
Feeder Protection
and Recloser Con-
troller 7SC80
Communication Module
DNP3 TCP
Bus Mapping/Point Lists
Preface
Contents
DNP3 TCP Device Profile 1
Point Lists 2
Flexible Mapping 3
Index

Disclaimer of Liability
This document has been subjected to rigorous technical review
before being published. It is revised at regular intervals, and any
modifications and amendments are included in the subsequent
issues. The content of this document has been compiled for
information purposes only. Although Siemens AG has made best
effortstokeepthedocumentaspreciseandup-to-dateaspossible,
Siemens AG shall not assume any liability for defects and damage
which result through use of the information contained herein.
This content does not form part of a contract or of business
relations; nor does it change these. All obligations of Siemens AG
are stated in the relevant contractual agreements.
Siemens AG reserves the right to revise this document from time to
time.
Document Release: C53000-L2040-C353-3.01
Edition: 09.2018
Product version: V1.05
Copyright
Copyright Siemens AG 2018. All rights reserved.
The disclosure, duplication, distribution and editing of this
document, or utilization and communication of the content are not
permitted, unless authorized in writing. All rights, including rights
created by patent grant or registration of a utility model or a design,
are reserved.
Registered Trademarks
SIMATICTM, SIMATIC NETTM, SIPROTECTM, DIGSITM,
SICAMTM,SIMEASTM, SINAUTTM, OSCOPTM, and DAKONTM are
registered trademarks of SIEMENS AG. An unauthorized use is
illegal.
All other designations in this document can be trademarks whose
use by third parties for their own purposes can infringe the rights of
the owner.
NOTE
For your own safety, please observe the warnings and safety instructions contained in this document.

3SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists
C53000-L2040-C353-3, Edition 09.2018
Preface
Purpose of this manual
This manual describes the bus mapping of SIPROTEC 4 Communication Module with DNP3 TCP.
Target group
Protection engineers, commissioning engineers, persons who are involved in setting, testing and service of
protection, automation, and control devices, as well as operation personnel in electrical plants and power sta-
tions.
Scope of validity of this manual
This manual is valid for SIPROTEC 4 Communication Module with DNP3 TCP.
Further support
Should further information be desired or should particular problems arise which are not covered sufficiently for
the purchaser's purpose, the matter should be referred to the local Siemens representative.
Hotline
Our Customer Support Center provides around-the-clock support.
Phone: [phone]
Fax: [phone]
Internet: http://www.siprotec.com
e-mail: [email protected]
Training courses
If you are interested in our current training program, please contact our training center:
Siemens AG
Siemens Power Academy TD
Humboldtstr. 59
D-90459 Nuremberg
Germany
Phone: [phone]
Fax: [phone]
e-mail: poweracademy[email protected]
Internet: http://www.siemens.com/poweracademy

Preface
4 SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists
C53000-L2040-C353-3, Edition 09.2018
Notes On Safety
Thismanual doesnotconstituteacomplete catalogof allsafetymeasures required for operating the equipment
(module, device) inquestion, because special operating conditionsmay require additionalmeasures.However,
it does contain notes that must be adhered to for your own personal safety and to avoid damage to property.
These notes are highlighted with a warning triangle and different keywords indicating different degrees of dan-
ger.
DANGER
DANGER means that death or severe injury will occur if the appropriate safety measures are not taken.
✧Follow all advice instructions to prevent death or severe injury.
WARNING
WARNING means that death or severe injury can occur if the appropriate safety measures are not taken.
✧Follow all advice instructions to prevent death or severe injury.
CAUTION
CAUTION means that minor or moderate injury can occur if the appropriate safety measures are not taken.
✧Follow all advice instructions to prevent minor injury.
NOTICE
NOTICE means that damage to property can occur if the appropriate safety measures are not taken.
✧Follow all advice instructions to prevent damage to property.
NOTE
It is important information about the product, the handling of the product, or the part of the documentation in
question to which special attention must be paid.

Preface
5SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists
C53000-L2040-C353-3, Edition 09.2018
Qualified Personnel
Commissioning and operation of the equipment (module, device) described in this manual must be performed
by qualified personnel only. As used in the safety notes contained in this manual, qualified personnel are those
persons who are authorized to commission, release, ground and tag devices, systems, and electrical circuits
in accordance with safety standards.
Use as Prescribed
The equipment (device, module) must not be used for any other purposes than those described in the
Catalog and the Technical Description. If it is used together with third-party devices and components, these
must be recommended or approved by Siemens.
Correct and safe operation of the product requires adequate transportation, storage, installation, and
mounting as well as appropriate use and maintenance.
During the operation of electrical equipment, it is unavoidable that certain parts of this equipment will carry dan-
gerous voltages. Severe injury or damage to property can occur if the appropriate measures are not taken:
• Before making any connections at all, ground the equipment at the PE terminal.
• Hazardous voltages can be present on all switching components connected to the power supply.
• Even after the supply voltage has been disconnected, hazardous voltages can still be present in the equip-
ment (capacitor storage).
• Equipment with current transformer circuits must not be operated while open.
• The limit values indicated in the manual or the operating instructions must not be exceeded; this also
refers to testing and commissioning

Preface
6 SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists
C53000-L2040-C353-3, Edition 09.2018

7SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists
C53000-L2040-C353-3, Edition 09.2018
Contents
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1 DNP3 TCP Device Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1 Data Objects Implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.2 DNP3 TCP Device Profile Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2 Point Lists. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.1 Binary Input Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.2 Control Relay Output Blocks/Binary Output Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2.3 Counters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2.4 Analog Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3 Flexible Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.1 Flexible Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Contents
8 SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists
C53000-L2040-C353-3, Edition 09.2018

9SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists
C53000-L2040-C353-3, Edition 09.2018
1 DNP3 TCP Device Profile
1.1 Data Objects Implementation 10
1.2 DNP3 TCP Device Profile Documents 13

DNP3 TCP Device Profile
1.1 Data Objects Implementation
10 SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists
C53000-L2040-C353-3, Edition 09.2018
1.1 Data Objects Implementation
The following table identifies which object variations, function codes and qualifiers the DNP3 TCP implemen-
tation of the Feeder Protection and Recloser Controller 7SC80 will support in both request messages and in
response messages.
For static (non-change-event) objects, requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with
qualifiers 00 or 01.
Requests sent with qualifiers 17 or 28 will be responded with qualifiers 17 or 28.
For change-event objects, qualifiers 17 or 28 are always responded.
Note
Further information see in the SIPROTEC 4 document Communication Module DNP3 TCP - Communication
Profile, order number C53000-L2040-C354 or in Internet http://siemens.siprotec.de/download_neu/
index_e.htm.
Table 1-1 DNP3 TCP implementation table
Objects Request Response
Object
No. Var. No. Description Function Codes (dec) Qualifier Codes (hex) Function Codes (dec) Qualifier Codes (hex)
1 0 Binary Input -
Any Variations 1 (read) 00, 01 (start-stop) 06 (no range)
07, 08 (limited qfy)
17, 28 (index)
1 2 Binary Input
with Status 1 (read) 00, 01 (start-stop) 06 (no range)
07, 08 (limited qfy)
17, 28 (index)
129 (response) 00, 01 (start-stop)
17, 28 (index)
2 0 Binary Input Change -
Any Variations 1 (read) 06 (no range, or all) 07, 08 (limited qfy)
2 2 Binary Input Change
with Time 1 (read) 06 (no range, or all) 07, 08 (limited qfy) 129 (response) 130 (unsol. resp) 17, 28 (index)
10 0 Binary Output -
Any Variations 1 (read) 00, 01 (start-stop) 06 (no range, or all)
07, 08 (limited qfy)
17, 28 (index)
10 2 Binary Output
with Status 1 (read) 00, 01 (start-stop) 06 (no range, or all)
07, 08 (limited qfy)
17, 28 (index)
129 (response) 00, 01 (start-stop)
17, 28 (index)
12 1 Control Relay Output
Block 3 (select) 4 (operate)
5 (direct op.)
6 (dir. op. noack)
17, 28 (index) 129 (response) echo of response